Search Documents

A panel discussion on carbon-in-pulp processing of gold and silver ores was one of the highlights of the 1981 AIME Annual Meeting in Chicago. The session generated considerable interest and discussion among panelists and the audience. For those unable to attend the panel, the program was recorded and the discussion appears in this two-part report. The panel was co-chaired by Robert S. Shoemaker, vice president of San Francisco Mining Associates, and Laurence D. Hartzog, principal engineer with Bechtel Civil and Minerals Inc., San Francisco, CA. Panel members included: George Potter, consultant, Tucson, AZ; Kenneth B. Hall, metallurgical superintendent, Homestake Mining Co., Lead, SD; and Donald M. Duncan, resident manager, Pinson Mining Co., Winnemucca, NV. There have been several types of carbon-in-pulp adsorption vessels in use, such as the Dorr-type agitator, the simple propeller agitated tank, the Pachuca tank, and, lately, the draft tube-type of agitated tank. Which one of these is best and why? Potter: On the selection of the most appropriate adsorption vessel, there is a considerable difference of opinion that stems largely from the fact that every ore is different. The mesh of grind, the pulp solids, and the apparent viscosity of the pulp as caused by its clay content and chemical conditions all differ. The traditional Dorr agitator with the slow speed center sweep and either peripheral or center column air lifts has worked quite well on the finer grinds of all minus 65 and probably 70-80% minus 200 mesh. Pachuca tanks have also been successful and they may be capable of handling a coarser feed than the traditional Dorr tank. One uranium mill, for example, handles minus 28 mesh sandstone ore in a Pachuca. The most recent development and one that commands consideration is the draft tube agitator in which there is a turbine which closely fits inside a draft tube. Velocity in the tube is carefully calculated to avoid undue shear and thus abrasion of the carbon. The objective in all cases, of course, is to mix the granular carbon, which is typically 6 x 16 mesh, very gently but thoroughly in a slurry with minimum carbon abrasion. I do not know that there is one outstanding choice just yet and I have been unable so far to get information on C-I-P service for ore grinds as coarse as 35 mesh. Duncan: The major advantage of draft tube-type is the ease of startup. At the Pinson plant we installed draft tube-type agitators but it is too early to quote experience with them. We also haven't operated long enough to determine just what our carbon loss is. The advantage, of course, in the draft tube design is that it requires only about one-third the horsepower input of a conventional agitator. If it has no other advantages, it has that. Hall: The type of vessel most suitable for C-I-P adsorption depends on the type of ore treated and the prevailing operating conditions. In most cases, a deep tank with turbine-type mechanical agitator and low speed tip velocities would be satisfactory. Turbine-type impellers give a positive type of agitation which assures optimum ion contact and reduces short circuiting. Thorough aeration is possible with an air sparge properly located. A mechanical agitator can easily be started up after an outage, but it is usually necessary to drain and wash out a Dorr rake-type or Pachuca before restarting. The turbine-type impeller requires more power, but maintenance costs are negligible if rubber covered impellers are used. Carbon losses are minimal. In smaller plants, Pachuca type agitators provide adequate aeration and agitation. Bob Polak, Occidental Minerals (from the floor): Mr. Hall, you favor the mechanical-type agitator with the preface that the proper design is critical. Could you elaborate on this for us? Hall: The most important thing is low tip speed to prevent carbon attrition. I think the impeller should be sized so that you get a good sweeping action toward the bottom of the tank, across its bottom, up the sides, and back to the center. The advantage of the draft tube is that you get a more positive agitation and you probably get improved aeration too. Polak: Do you know of anyone using an upflow mechanical agitator rather than a downflow unit? Hall: I think that Bob Wilson at Custom Equipment has designed one where he has located the sparge directly beneath the impeller. The air bubbles are broken up by the impeller as the slurry passes through it. The slurry flows upward, outward, down the sides, and, again, back to the center of the tank. I don't know that any tanks of this design are in commercial use. Hans Von Michaelis, Randol International (from the floor): A question to any of the panelists on flat bottom versus conical bottom Pachucas. Hall: I would say the conical bottom would be most suitable in most cases. Some plants have experienced problems with flat bottom Pachucas in that they have a tendency to sand in on the sides of the tank so only the center of the tank is active. Duncan: With our draft tube tank we placed an inverted cone in the center of the tank bottom and blanked off the bottom comer around the circumference of the tank to facilitate movement of the pulp. Other than that, as far as conical bottom tanks are concerned, I'm generally opposed to them because of the cost and height differential. Larry Kramer, Kennecott Minerals Co. (from the floor): Mr. Duncan, you mentioned that the draft tube-type could be agitated with about one-third the horse-power applied to a conventional propellor agitated tank. I have trouble trying to pin down that kind of number. Could you give a bit of rationale as to why that mechanism has a lower horsepower requirement? Duncan: I think it has to do with the fact that below the propeller you have straightening vanes. The pulp, which is flowing vertically downward, is turned and flows upward again without any recirculation. You have an inherently less horse-power requirement in that type of tank. The one-third horsepower requirement is a number I obtained from Lightnin, which supplied us with details of the draft tube. There is probably much more recirculation with a conventional impeller type that is wasted motion. Potter: Last week I saw some agitators in South Africa with short draft tubes and actual turbine-type impellers. This plant was handling 200 kt of ore per month. The tanks were flat bottomed, and the agitation appeared to be quite satisfactory.

Jan 8, 1981

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Todd Loudin

A majority of the chemical process industry uses lime in either a powder or liquid form. Engineering and maintenance personnel often face a long and potentially expensive trial-and-error period in order to find the best process equipment to handle lime. Limestone is mined from a quarry in the form of calcium carbonate (CaCO3). Then, it is crushed and fed into a kiln at approximately 1,093° C (2,000° F), where the carbon dioxide is burned off (calcining) to make calcium oxide (CaO).

Jan 1, 2010

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By Carla L. Zenti

In recent years, considerable advances have taken place worldwide in the design and construction of first tunnel linings. With these advances, there is a tendency to move away from traditional support that includes heavy open profiles of rolled steel arches, to a lighter solution with the use of an optimized tubular steel cross section rib, and shotcrete reinforced with steel mesh and/or steel fibers, providing a continuous support (Lunardi, 1982). The development of tubular ribs has provided greater design options, increasing flexibility to engineers and contractors while providing a efficient and cost effective construction method. In this article, the authors describe numerical and experimental investigation on this problem, suggesting as a new first lining steel arch design approach by using tubular ribs cross section as new technical solution for first lining underground support.

Jan 1, 2012

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By Saul J. Esdalera

The flotation response to amine collector and its adsorption on the mineral surface was studied as a function of pH and collector concentration. The flotation response increased in the order anorthite + intermediate plagih clases + albite, while adsorption of amine obeyed the Freundlich equation r = A.Cn. This adsorption is proposg to be due to a covalent bonding between the AlOH surface pups of the plagioclase altered outer layer and the amino group of the collector. Finally, the study showed thatmtial dissolution of the solid phase provides the necessary conditions for amine attachment on the mineral particles and consequent flotation.

Jan 1, 1980

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step-function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step-function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another is-sue is how they compare to peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines' program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau's continuous residue processing plant, College Park Metallurgy Research center.' The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016