Search Documents

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Robert Kimutis, Heather Dougherty, Eric Watkins

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry as a predictive tool for planning and monitoring and can assist with a well breach scenario over a large mining area. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Oct 12, 2023

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

The mining and minerals extraction industries have often been demonized by the public as industries that put profits and production before people. It is true that the inherent danger of the work has led to more fatal accidents than anyone associated with the industry would care to remember. But, in stark contrast to what has often been said, the truth of the matter is safety is now the top priority of every miner, from the face of the longwall to the executive boardroom. Without safety, nothing else matters. This message was told and retold by representatives from some of the world?s top mining and petroleum companies from Oct. 11-13 during the inaugural Safety and Reliability in the Mining and Resources Industries Conference in Calgary, Canada. The meeting was hosted jointly by the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) and the Society for Mining, Metallurgy, and Exploration (SME). It was the first of a series of conferences to focus on these important topics. Next year, the conference will be held in Minneapolis, MN from Nov. 13-15.

Jan 1, 2011

By D. R. Hanson, H. Lawson

In this study, NIOSH researchers conducted a machine learning analysis to examine whether a model could be constructed to assess the probability of dynamic failure occurrence based on geochemical and petrographic data. Random forest, cluster analysis and dimension reduction were all applied. The objective of dimensionality reduction was to explore patterns and groupings in the data and search for relations between compositional parameters. Cluster analyses were performed to determine if an algorithm could find clusters with given class memberships and to what extent misclassifications of dynamic failure status occurred. A random forest analysis performed on data from the Pennsylvania Coal Sample Databank cross-referenced with accident data from the Mine Safety and Health Administration (MSHA) determined that 7 parameters of the 18 examined exerted the most influence on results. Cluster analysis on data after dimensionality reduction resulted in a hierarchal clustering algorithm finding four clusters, with one relatively distinct dynamic failure cluster, and three clusters consisting mostly of control group members but with a small number of dynamic failure members.

Feb 1, 2023

By G. A. Perry

Cyprus Sierrita is a major producer of copper and molybdnum from its Sierrita and Twin Buttes open pit mines south of Tucson, Arizona. Both pits were started in the late 60's and are in excess of 1500 feet in depth. Sierrita has utilized a Cat 992C Remote Controlled Loader since January 1993. The loader was justified to increase SAFETY and PROFITS at Sierrita. It has exceeded all expectations. As of June 1993, it had produced additional profits totaling more than $1,500,000.

Jan 1, 1994

The 1996 Arizona Conference was held in Tucson on Dec. 8 and 9. Attendance was 648, a 12% increase from the 1995 conference. The annual conference is organized by the Arizona Conference Board of Directors, representing SME sections from throughout Arizona and adjacent areas. In addition to those representing mining and processing operations in the Arizona region, the meeting was well attended by interested parties from throughout North America. These included vendors, consultants, academia, research organizations and corporate management. The technical program highlighted the meeting. It consisted of a keynote address and morning and afternoon technical sessions. In the technical sessions, 23 papers were presented by the mining, hydrometallurgical, smelting, geology and mineral-processing divisions. The conference was then capped by a banquet that included a talk by a noted economist. Keynote address The program was kicked off by a keynote address titled "Forecasting for the 105th Congress," by Rep. John Shadegg (R-AZ). He was elected to Arizona's Fourth Congressional District in 1994. Shadegg serves on the House Budget Committee, the Resources Committee and the watchdog Government Reform Committee. He stressed the familiar conservative positions of reducing government spending, balancing the budget and states rights. As a member of the House Resources Committee, Shadegg stated his support for the mining industry. Technical sessions Mining division. Two of the five presentations described developments at two Arizona mining operations. T.J. Swendseid of Phelps Dodge presented a paper titled "New developments at Morenci" and P. Garretson of BHP presented a paper titled "Startup of the Robinson Project." Morenci continues to expand its operation and recently broke records for production. Other developments at Morenci included the completion of a 600-m (2,000-ft) drainage tunnel and stockpile rehandling. In addition, Phelps Dodge moved Morenci's crusher plant. It was completely disassembled and reassembled in just eight days. Another interesting presentation was "Predictive maintenance techniques for large electric shovels at Cyprus Sierrita," presented by T. Ritzel of Cyprus Amax. The presentation described high-technology methods for predicting maintenance problems. These methods included vibration analysis, ultrasonic detection, infrared thermography, electrical measurements and tribology (the science of lubricant evaluation). The benefits of these techniques are reduced downtime of the equipment, as was demonstrated in case studies at the mine. The other presentations were "Introduction to NOSA 5-star safety program," by R. McKinnon, BHP Copper North America, and "A new design guideline for mine sealing," by K. Fuenkajorn, Rock Engineering International. Hydrometallurgical division. The hydrometallurgical session consisted of five papers. These included a presentation titled "Recovery of gold and silver using guanidine-based extractants," by M. Vining of Henkel Corp., Tucson, AZ. In this presentation, guanidine-based extractants LIX-79 and AURIX resin were introduced. LIX-79 was shown to have applications in copper-gold and high silver ores. In ammonia-cyanide leaching, AURIX was shown to be more selective in CIL vs. RIL comparisons. Other papers in the hydrometallurgical division included "Application of cobalt in the copper industry," by J. Hawke, OMG Apex Inc.; "Series parallel conversions and production gains at Cyprus Miami Mining's dump leach and solvent extraction operation," by E. Bilson of Cyprus Amax; "Lead alloy anode corrosion at the San Manuel SXEW tankhouse," by W .M. Gort of BHP Copper and "Hydrometallurgical treatment of copper refinery slimes," by B.C. Wesstrom of Phelps Dodge. Smelting division. Three papers were presented in the smelting division session. These included updates and reports on improvements at the Hayden, Hidalgo and BHP San Manuel smelters. For example, W.A. Dutton of Phelps Dodge presented "Recent improvements at the Hidalgo Smelter." These changes were aimed at reducing environmental emissions and increasing production. They included modifications to the fugitive-gas collection system to reduce particulate emissions, rubber lining the acid plant scrubbers to reduce corrosion and the installation of a cold lime softening system for water treatment. Equally interesting papers were presented by D. Norton of Asarco, Hayden, AZ, in a paper titled "Update of the Hayden smelter process," and by D. Jones of BHP Copper, San Manuel, AZ, in a paper titled "Update on first campaign of the BHP San Manuel Copper." Geology division. The session began with a paper that outlined the progress of an exploration project in South America. "The Pierina exploration project, Ancash Province, Peru" was presented by J.D. Lowell, Lowell Mineral Exploration, Rio Rico, AZ. Another paper was then presented on a copper deposit in Grant County, New Mexico. "Zonation of supergene copper minerals at Hanover Mountain, Grant

Jan 1, 1997

By E. Watkins, R. Kimutis, H. Dougherty

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry and can assist with a well breach scenario. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Mar 2, 2022

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, in spite of the low-grade nature of the ore, has become one of the largest production-scale and most profitable non-ferrous metal mines in China. The successful application of hydrometallurgy as well as proper engineering design are the key factors for large-scale development of the Zijinshan gold-copper mine. In this contribution, the practical experience acquired in the development of the Zijinshan gold and copper mines is summarized. This covers most aspects of the production process including mining, beneficiation, ore stacking, heap (bio)leaching, carbon-in-leach, solvent extraction, electrowinning, wastewater and tailing treatments. The authors believe that this practical experience will not only help to promote the development of hydrometallurgy, but can also serve as a model for other gold and/or copper plants around the world.

Jun 3, 2020

By Arthur Miller

Most of the production of copper in the United States comes from a few large companies. Often overlooked, however, are the more numerous small mining operations, which collectively produce a significant portion of the nation's copper. The objective of this paper is to describe the operations of a small mining company - Ranchers Exploration and Development Corporation - how it views its place in this industry of giants, how it exploits the advantages offered by its relatively small size, and how it protects itself from the hazards being small introduces. Environment is, of course, a critical factor for such a company because it does not have the resources which help large companies weather periods of financial stress. Ideally, this environment is characterized by a heal thy economy, strong product demand, relatively stable prices , adequate grades and tonnages of ore commensurate with depth and over-burden, ready access to utilities, a dependable labor pool, and suitable technical "know how". When the environment is right, properties which were previously uneconomical to operate attract the attention of companies whose primary interest is a return on investment commensurate with risk over a reasonable period of time. Naturally, the amount of the investment and the duration of operation determines the size of the company which would be interested in such a venture. Such is the case with Ranchers Bluebird Mine at Miami, Arizona - a small property operated by a small company in a favorable economic environment.

Jan 1, 1967

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By S. Perla

Two of Peabody Western Coal Company's mine operations are the focus of this paper ... Black Mesa Mine and Kayenta Mine, both located in Northern Arizona. These two locations are unique for a variety of reasons. ? The two mines have only two customers, both power plants, one the Southern California Edison's Mohave Generating Station near Laughlin, NY, the other the Navajo Generating Station near Page, AZ. Close in proximity, these two locations ships nearly 12 million tons of coal per year. ? Material is shipped to these customers two ways: via a 273 mile underground slurry pipeline, which by the way is longest in the world, and by a 17 mile long conveyor to four storage silos. Product is then shipped via train from the storage silos to the plant sites.

Jan 1, 1995

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By Diogo Peixoto Cordova, Italo Gomes Gonçalves, Andre Cezar Zingano

The top-down extraction sequence in the sublevel open stope method relies on rib pillars to support excavations, making pillar and stope stability crucial for controlling dilution. This study introduces an integrated methodology using a genetic algorithm to optimize the layout of open stopes and rib pillars while considering both economic and geomechanical performance. The methodology incorporates user-defined parameters such as the minimum size of stopes and pillars, maximum accepted dilution and acceptable percentage of pillar failure. A profit function that attributes economic value to the geometric configurations, including geomechanical performance, is employed. The geomechanical performance, assessed using numerical models in FLAC3D, includes the average percentage of pillar failure and potential dilution. The study was tested on a mining panel from an underground gold mine using a top-down mining sequence. The optimization achieved an 8 percent increase in net profit compared to the traditional engineer’s design when 70 percent hangingwall support efficiency was assumed, and a threefold reduction in pillar failure percentage. When no hangingwall support was considered, the net profit increase reached 22 percent. These results demonstrate that the proposed methodology enables integrated optimization, balancing mining costs with geomechanical performance and reducing the need for secondary support compared to traditional methods

Nov 1, 2024

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By Paul L. Bearden

The accumulation, handling, and utilization of sludges formed from wet process phosphoric acid is one of the major problems in the industry. The purpose of this paper is to explain some of the considerations and techniques that can be employed to provide some measure of control over the problem. An acid made from a Central Florida phosphate rock is used to illustrate the effects of one process design approach used to provide one type of control. Other approaches or techniques are discussed on a general basis. In every case, the discussion is purposely limited to conventional dihydrate processing in which phosphoric acid is produced from the filter at a strength of approximately 30% P205 and is subsequently concentrated to higher strengths such as 44 and 54% P205.

Jan 1, 1966