Search Documents

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000'] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By G. H. Friedrich

The distribution of mercury in soils, rocks, and ore was studied in three areas of the Pachuca-Real del Monte District: (1) An area north of the town of Pachuca where ore veins have been found at or near the surface. The mercury content of soil samples taken near the vein zones is far above the background value. The highest value was 1900 ppb (parts per billion) mercury in a soil sample above Veta Vizcaina; the background is about 50 ppb Hg. (2) In the area north of the town of Real del Monte where only a few of the veins are known to crop-out. Regardless of exposure, soils collected over veins show anomalous mercury values ranging from 250 ppb to 1900 ppb. (3) In an area south of the town of Real del Monte. Here, although vein outcrops are lacking, mineralization is known at a depth of about 120 m. All soil samples taken at 50 m. intervals along an east-west traverse contain anomalous amounts of mercury, with peaks corresponding with the known location of the veins.

Jan 1, 1965

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By Barbara B. Newlin, Emily Rosenberg, Marianne Snedeker

Whose longwalls perform best in Eastern underground mines? What is the latest legislation affecting slurry pipelines? What are the trace element constraints on magma genesis? How can process set points be controlled more economically without affecting product quality? Where can I get a paper presented at the Australian Coal Preparation Conference? If answers to questions like these can help with your management decisions, exploration plans, or market positioning, your firm should know about Information on Demand. Information on Demand, Inc. (IOD) is a research service available to SME members to help them get the facts needed to develop business plans. IOD can function as a research staff and data bank specialist for geologists, planning specialists, production managers, and engineers in all levels of the mining industry. Just dial 415-549-3259 and ask IOD for a copy of an obscure article, a comprehensive literature search, or a background report on a company, a process, or a product. Within a short time, IOD will have the information you need delivered to your office or worksite. Information on Demand has a bank of dial-up terminals that provide access to more than 200 business and technical data bases, including Lockheed's Dialog, CompuServe, InfoLine, The New York Times Information Bank, and other systems. These data banks contain more than 95% of the world's technical literature published in the last 10 years. There is no input required from individuals or companies. The data bases are maintained by publishers and are constantly updated with abstracts of articles, reports and reviews, and other text appearing in more than 5,000 engineering publications, as well as thousands of other trade and technical publications. The data bases are organized by subject and offer a speedy comprehensive survey of world literature. One data base, called Compendex, provides worldwide coverage of engineering publications, meetings, and reports. The Metadex data base abstracts literature on the science and practice of metallurgy, and can be accessed by commercial, compositional, and numerical alloy designations. PatSearch and Claims data bases enable IOD to determine what patents have been filed by a given entity, what international patents are equivalent to a US patent, and other vital patent information. In the non-technical arena, the Commerce Business Daily has daily updates of federal procurement information. The Federal Register is abstracted on-line in a data base, and ABI/Inform is a data base full of marketing and management information for all industries. IOD offers a free pamphlet listing these and other data bases. A typical literature search from IOD will produce 60-200 references with abstracts, and can be printed out off-line and mailed or transmitted directly to an electronic mailbox. Abstracts will often give all the information needed by the reader. At times, when the complete article or technical report is needed for further study, IOD will send a photocopy of the full text for a small additional fee. Patents, books, securities exchange filings, standards, and specifications can also be supplied by means of IOD's network in major libraries, such as Harvard, MIT, and The Library of Congress. A technical translation service is available for foreign

Jan 12, 1983

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Andrew K. Simpson

What will this deal do to the company’s stock price? This question arises when a publicly traded mining company is presented with a new mine project, or business combination. The standard tool for addressing this question is to use discounted cash flow analysis, or net asset value(NAV), which is discounted cash flow net of liabilities. Cash flow-based analysis is invaluable for assessing project costs and other impacts on debt service capacity and internal rates of return. But cash flow analysis and NAV do not work very well for stock price analysis.

Jan 1, 2000

By Terry R. Guilinger

A minitest of the new potassium chloride-potassium carbonate two-stage in situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing carion-exchange reactions. The test a1 so indicates permeability anisotropy and the existence of disturbed flow fields. The research was partially funded by the U.S. Bureau of Mines.

Jan 1, 1984

By I. Chatterjee

The application of microwaves has a demonstrated potential for the ultimate removal of water from fine coal. The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems drilling microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper the dielectric properties of various ranks of coal are presented as a function of frequency and moisture content. The measured dielectric data are incorporated into electromagnetic and thermal models of coal which predict the energy absorption and temperature distribution during microwave heating.

Jan 1, 1990

By J. A. Herbst

It is widely recognized that Semiautogenous Grinding (SAG) circuits require the use of effective process control techniques to achieve their full processing potential and to protect them from the harmful effects of overloads and grind-outs. This requirement is even more essential as the variability of the ore being processed increases. The new Chino Mines Company concentrator located near Santa Rita, New Mexico started operation in June of 1982. At least eight major rock types are mined and milled. Ore hardness, feed size, and specific gravity are quite variable. Typical feed rates per grinding line are 850-900 tph but extremes of 260-1200 tph have been encountered. Normal feed rate variations of between 400 and 1100 tph are encountered on a weekly and sometimes daily basis. Feed size varies with rock type from a maximum of eight inches for the harder ores to two inches for the softer ores. One somewhat unique characteristic of the Santa Rita ore body among major copper mines is the wide variation in ore specific gravity. Specific gravities of the major rock types range between 2.7 and 3.6. The specific gravity variations are due to large changes in magnetite concentration throughout the pit. The result of this is large variations in SAG mill throughput which can have a harmful effect on downstream ball milling and flotation performance. Due to these wide fluctuations in ore characteristics, it was recognized soon after startup that successful operation of the grinding circuit and the plant at large was dependent upon the development of an effective automatic grinding control strategy. Research at the University of Utah has suggested that control based upon critical but difficult or costly to measure variables would improve automatic control performance. A project team made up of the Chino process control staff, Kennecott's Process Control department and the University of Utah Metallurgy Department was established to assess these concepts at Chino. This paper describes the development and on-line plant implementation of an Extended Kalman Filter that uses simple models of the SAG milling process, to predict the volumetric loading, the rock mass, the water mass, and the ball mass within the SAG mills at Chino. The on-line estimation of these parameters is the first step in the development of an integrated SAG mill/ball mill control strategy which is hoped to L eventually maintain the grinding circuit at its maximum capacity, while balancing the grinding load between the SAG and ball mills. Examples of long term estimation with the models and filter are shown for typical operating conditions as well as a SAG mill overload and grind-out.

Jan 1, 1983

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

By Clayton J. Parr

Introduction This chapter contains brief discussions of various environmental protection requirements that relate to underground mining operations. Environmental disturbances at an underground mining operation can result from subsidence; water discharges; waste dumps; construction and operation of access roads and utility lines; construction and operation of surface facilities such as maintenance shops, bathhouses, and storage yards; and emanation of dust and noise from surface crushers. Construction and operation of a concentrator or washing plant may result in the emission of air pollutants, the discharge of water pollutants, the creation of noise, and disturbance of the surface. Tailings ponds can be the source of fugitive dust.1 This chapter is not intended to provide a detailed discussion and analysis of laws and regulations dealing with environmental protection. Rather, its purpose is to provide the engineer with a basic awareness of the existence and nature of such laws and regulations, as well as the procedural requirements that must be followed in complying with them. The body of law relating to environmental protection has grow" very rapidly and should continue to do to for some time. Because many of the laws have been enacted recently, numerous court decisions are being rendered to resolve disputes over their interpretation. Hence, the reader is cautioned to be alert for subsequent modifications of statutes and regulations, and new case law. Rules and regulations pertaining to environmental protection are implemented at all governmental levels. The most widely known laws are those enacted by the federal government that have nationwide applicability. However, separate requirements exist in each state, county, and municipality. Because of their general applicability, federal laws are discussed most extensively in this chapter. Ownership of the property is the most significant factor considered in ascertaining what rules govern the conduct of an operation thereon. If the land is held under lease, reference to the lease terms must be made in the first instance to determine what obligations must be met in order to prevent default and possible loss of the property. If the land is held under a lease from the federal government, the operator is subject not only to compliance with the lease terms, but also to a large body of laws and administrative regulations that pertain generally to the conduct of mining operations on land held under federal leases. Although operations on unpatented mining claims, the legal title to which remains in the federal government, are not subject to the same rules and regulations that are applicable to operations conducted pursuant to federal leases or permits, they soon will be governed by a special set of regulations that provide for protection of surface resource.2 Operations conducted on lands leased from a state usually are subject to numerous environmental protection requirements specified in the lease terms, in addition to rules and regulations promulgated by the state agency having jurisdiction over mining on state lands. Operations conducted on privately held lands are subject to fewer such requirements. Leases from private parties sometimes have environmental protection and reclamation requirements written into them, but generally to a far lesser extent than governmental leases. Operations conducted on properties owned by the operator are subject only to those laws and regulations that have general applicability without regard to land ownership. COAL SURFACE MINING CONTROL AND RECLAMATION ACT OF 1977 Introduction On Aug. 3, 1977, the Federal Surface Mining Control and Reclamation Act of 1977 was signed into law.3 It governs coal-mine operations on private lands, as well as on public lands. The Act is pervasive in its scope and is extremely long and complex. The basic purpose of the Act is to control and minimize the environmental effects of surface coal mining. Surface coal-mining operations are defined as activities conducted on the surface of lands in connection with a surface coal mine and surface impacts incident to an underground coal mine.4 The Act is administered by the Secretary of the Interior through a new agency named the Office of Surface Mining Reclamation and Enforcement.5 The Act contains detailed environmental protection standards and reclamation requirements, and it establishes a permit system for all surface coal-mining operations. Mining in certain areas and under ceri-in conditions is restricted or prohibited, and a mechanism for enforcement by the states is provided. Stiff penalties are provided in the event of noncompliance. Implementation Schedule Nonfederal Lands: As required by Section 501 of the Act, interim regulations setting mining and reclamation performance standards based on and incorporating standards set out in Section 502(c) were adopted effective Dec. 13, 1977.6 They will. be incorporated as amendments to Chapter VII of Title 30, Code of Federal Regulations. Permanent regulatory procedures for surface coal-mining and reclamation operations performance standards, which were directed to be promulgated by Aug. 3, 1978, were published in proposed form on Sept. 10, 1978. 7 They govern surface coal-mining operations in any state until a permanent state or federal program is adopted. As of Feb. 3, 1978, all new operations, and as of May 3, 1978, all existing surface coal-mining operations, on lands on which such operations are regulated by a

Jan 1, 1982

By J. C. Bradbury

The Illinois State Geological Survey's program in industrial minerals is twofold-the gathering of information on mineral raw materials and the generation of data on the use of these materials. The first function is carried out by the Industrial Minerals Section and the Clay Resources and Clay Mineral Technology Section of the Geological Group, and the second is the responsibility of the Chemical Engineering Section of the Chemical Group. Gathering in formation on raw materials includes both mapping of resources and fundamental geological research. Recent and current research projects include studies relating lithologies of limestones to their physical properties, investigation of sulfur dioxide reactivity of various types of limestone, lithostratigraphic studies of limestones of Mississippian age, investigations of heavy minerals in Cretaceous, Tertiary, and Pleistocene sands, studies of the environments of clay deposition, electron microscope studies of clays and limestones, and investigation of long-term expansion in ceramic products. A relatively recent development that relates more to dissemination of information than to research is environmental geology. This affects the Survey's industrial minerals program chiefly by stimulating the study of rock and mineral resources in metropolitan areas and reporting the results for the land- use planner as well as the engineer or mineral producer. The Survey's program of research on the use of industrial minerals was expanded and diversified in 1966. Incorporating a minerals beneficiation lab, the program is designed to develop new uses for existing mineral resources and to assist producers in implementing these ideas: Projects of the minerals engineering program have included the separation of a feldspar concentrate from certain glacial outwash and river sands, recovery of kaolinite from the waste from silica sand operations, development of the use of an Illinois clay as a binder for pellets, and investigations into the use of fly ash and fluorspar mine tailings.

Jan 1, 1970

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By D. Tao

Reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In this process, quartz is often floated with ether amines (R?(OCH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of quartz does not work well if a certain amount of slime is present in the ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the efficiency of iron ore flotation by the use of a new type of depressant for clay and iron minerals, Georgia Pacific (GP) clay binder. The GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It also helps depress hematite flotation due to its unique chelating action on iron ions. The results from this study show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing iron recovery to 78.15%, while the concentrate grade remained stable at 67.08%. Keywords: Georgia Pacific clay binder, Iron ore flotation, Flotation efficiency

Jan 1, 2010