Search Documents

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By H. P. Hatch

Ash is a material that many people leave to nature to handle. Others sometimes sweep it under the rug to be disposed of by someone else. In our business we cannot do either. In fact the American Electric Power System spends many millions of dollars in plant investment costs to collect the material, and then many more millions to dispose it. In 1965 alone the coal fired steam generating plants in., the AEP System produced approximately 2,400,000 tons of ash, enough to fill 40,000 coal cars which would extend as a single train across the entire states of Ohio and Indiana. Even though our present ash production is large, this is only the beginning when we forecast the future growth of our system. By 1980 it is estimated that our generating capacity will expand to about three times its present size, and with coal as our primary source of fuel our ash production will increase proportionately to about 7 million tons a year.

Jan 1, 1966

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By C. B. Manula

The application of computers to materials handling problems has recently been investigated by various mining groups. This approach has been found, especially useful where a large amount of alternatives must be investigated prior to arriving at a final decision. These alternatives may be expressed in terms of man hours, units and types of equipment such as trucks or conveyors, or the allocation and operation of proposed or existing haulage facilities. The decision problem becomes especially evident when we consider the mechanical revolution which has flooded the mining industry in recent years. The industry has become highly competitive, with the need to keep low profit materials away from high cost production faces ever increasing. The capital investment required for the highly sophisticated equipment that is necessary to perform this function is generally great, and management is faced with decisions which must all too often be made without sufficient data.

Jan 1, 1967

By S. Veeramasuneni

The sign of the surface charge for alkali halides in their saturated brines has been established from non equilibrium electrophoresis measurements and on this basis the flotation response of alkali halides was explained based on the adsorption of oppositely charged collector colloids by heterocoagulation. These surface charge results for alkali halides are generally as expected from simplified lattice ion hydration theory with some exceptions, specifically LiF, KCI, NaCl, KBr, RbBr, KI, and Rbl .The presence of natural oxygen defect states in the crystal lattice and the inaccuracies involved in the gaseous ion hydration free energy values used appear, in past, to be responsible for these deviations. The presence of natural oxygen defect states in KCI, KBr, RbBr, and Rbl as characterized by UV Nis absorption, was found to account for their anomalous surface charge. Further, other positively charged alkali halides, LiF, NaCl and KI, were found to be free of oxygen defect states. Nevertheless, oxygen defects can be created in these alkali halides to make them negatively charged and has been demonstrated for NaCl. Such negatively charged NaCl can be readily floated with positively charged amine collector colloids thus confirming the surface charge/collector colloid adsorption theory.

Jan 1, 1996

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Atta Ur Rehman, Kwame Awuah-Offei

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis in community engagement programs to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This article proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies.The mineral industry provides raw material for industrial activity to support society (Martens and Rattmann, 2001). Mines have changed from conventional mining practices to sustainable ones because of the negative impacts of mining in the past and increased public awareness (Wang et al., 2016). The concept of sustainable mining is getting mature, as stakeholders (e.g., governments, investors and host communities) are getting more involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in the failure to acquire a social license to operate (SLO) (Thomson and Boutilier, 2011). The SLO, if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomson and Boutilier, 2011).Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 4, 2018

By Elizabeth Anne Semon

The marketability of a large volume bulk material is significantly effected by transportation costs. Hence, it is essential for anyone that deals with minerals or mineral wastes to be able to reliably estimate bulk transport costs. The three types of bulk overland transportation modes that will be discussed are truck, railroad, and pipeline. Contract and private carriage are the two types of truck transport generally suitable for movement of bulk commodities. Contract carriers are those transportation firms that service a limited number of shippers and geographic points, and carry a restricted number of commodities. Private carriage consists of control over drivers and equipment by the shipper, ownership or lease of the transport equipment, and shipment of commodities related to the primary business of the shipper.1 A combination of private and contract carriage may also be used. Depending on the size and regularity of the shipment, rail offers single car, multiple car, or unit train service to move bulk minerals. Both long and short distance pipeline transportation has been shown economically and technically feasible for many different solids such as, mine and quarry products, coal, chemicals, copper concentrates, phosphate rock, and sewage sludge. 2

Jan 1, 1973

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

Evver since it first displayed an autonomous mining truck at the 1996 MinExpo show in Las Vegas, NV, Caterpillar has been building the blocks to a fully autonomous mine. In May, the company unveiled another block in that progression, the new Cat MineStar System that it says is ?the industry?s broadest, most comprehensively integrated miner operations and mobile equipment management system.? The full system is comprised of five capability sets ? Fleet, Terrain, Detect, Health and Command ? to help operators define the size and scope of their management system based on the needs of their mining operations. Michael Murphy, technology and autonomy manager for Cat Global Mining, explained that the customers were not ready for an autonomous mining truck in 1996, but that many customers wanted the building blocks to eventually get to autonomous mining. After 15 years of work, Murphy said the building blocks have come together in the form of the Cat MineStar System.

Jan 1, 2011

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By Edward K. Davison

The so-called "construction aggregates," sand and gravel, crushed stone, and several kinds of metallurgical slags, are used principally in the construction and maintenance of all kinds of roads, engineering structures, buildings, homes, airports, etc. Production of these aggregates is approaching two billion tons annually. In terms of tonnage produced, sand and gravel has been the leading mineral since 1954, with crushed stone gradually approaching an equal tonnage. Sand and gravel is of widespread occurrence and of wide variation in suitable gradation and quality. It is a low-value, heavy-loading, short-haul commodity. These characteristics account for the historic concentration of production tonnage in and near urban areas where construction activities are concentrated. The combination of improved urban and near-urban highway systems and the steadily rising rail rates for short-haul traffic has fostered a consistent change since World War II from rail to truck transport, with trucks now accounting for more than 807 of the tonnage moving away from the production sites. While there are increasing numbers of exceptions, truck transport of sand and gravel is generally limited to about 30 miles. The expansion of the urban and near-urban areas of even moderate density, which became so pronounced after World War II, has been the source of most of the sand and gravel industry&apos;s environmental difficulties. Dust, noise and truck traffic associated with the operations -- particularly truck traffic -- have, of course, generated public complaint. This has been particularly true in those many cases where housing developments have approached and even surrounded sand and gravel operations which were in operation before the development started.

Jan 1, 1974

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017