Search Documents

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Vladislav Kecojevic

Both Canada and the United States are endowed with significant reserves of mineral resources. Mining industries in these two countries have a strong safety and health culture; skilled, dedicated and well-paid workforce; applications of state-of-the art technologies and high productivity, strict environmental requirements and social responsibility. Both countries are global leaders in safe, economic, productive, environmentally responsible and sustainable mining practices. Mining schools/ departments in Canada and the United States provide a strong and comprehensive education and training, hands-on learning experience, with support for internships and co-op opportunities to prepare graduates for careers not only nationally but also in the global mining industry. While there are many similarities in their industries and mining schools, there are also some differences. This article examines the contribution of mining to the economy, the political climate, the regulatory framework, the investment climate, environmental regulations, the language, the perception of mining, news and press coverage, and the academic landscape in both countries. Opinions, observations and perspectives shared in this article are of the author, and do not necessarily reflect the views, policies or positions of any organization, employer or affiliated group.

Nov 1, 2025

By Manuel S. Rivera

Abstract. Instrumentation in concentrators has evolved from a few isolated indicators to compu- terized control within twenty years. This evo- lution has caused a drastic change in the phil- osophy, personnel and equipment used in a pro- gram of servicing and utilization of present day automation.

Jan 1, 1980

By W. N. Hamilton

British Columbia is geologically favourable for a rich variety of industrial mineral occurrences. Some have been produced for years, others overlooked until recently. Major production occurs for asbestos, gypsum, limestone, magnesite, silica and sulfur; lesser production for a dozen others. For several of the minerals, potential is much greater than existing production. New production opportunities exist also for diamonds, niobium and REE minerals, fluorspar, kyanite, nepheline syenite, talc, and several others. Alberta, though geologically less diverse, also has many industrial minerals. Limestone, salt and sulfur have the major production; clay and shale, silica, sodium sulfate and a few others lesser production. Opportunities exist for expanded production, and for new production in heavy (Ti -Zr) minerals, formation brines (Ca-Mg-I-Li), and gypsum.

Jan 1, 1987

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By R. Reddy Kallu

Prior to July 2007, the only accepted method by MSHA for evaluating the mine seal design and performance is the full-scale explosion tests conducted in the NIOSH?s Lake Lynn Experimental Mine (LLEM) for deeming a seal design suitable for use in U.S. coal mines. Since the new regulations came into effect use of these conventional full-scale explosion tests for evaluating mine seals for the new elevated design standards may not be practicable. Generation of such high explosion pressures in experimental mines is dangerous and may cause permanent damage to the testing facilities. Further, they require significant amount of time, labor and money. Considering these factors, there is a need to develop scientific methods for evaluation of new seal designs and for understanding the dynamic seal response. This paper tries to address the reinforced concrete (RC) seal design using the three dimensional finite element based explicit software ABAQUS. Full-scale explosion test data available from NIOSH?s LLEM on 20 psi reinforced concrete seal is used for validating the numerical models. Further in this paper, based on the results from the validation models, a reinforced concrete seal is designed for 120 psi design standard for typical entry dimensions.

Jan 1, 2009

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By J. C. Edwards, C. C. Hwang

A computational fluid dynamics (CFD) program was applied to fire spread along combustibles in a ventilated mine entry. The rate of flame spread was evaluated for the ribs and roof of a coal mine entry; timber sets; and a conveyor belt. The CFD program models char forming materials with temperature dependent thermal properties. The program solves three dimensional time dependent flow equations with a mixture fraction model for the gas phase reactions. Radiant heat exchange is evaluated for non-scattering gas. The CFD program predicted a flame spread rate of 0.0145 m / s for an actual coal mine fire in which the estimated flame spread rate was 0.0086 m / s. This overestimated flame spread rate was a possible consequence of the presence of inert materials in the mine entry’s roof and ribs. CFD fire spread rate predictions of 0.043 m / s and 0.73 m / s bounded the measured value of 0.27 m / s for fire spread along Douglas Fir timber sets in a tunnel.

Jan 1, 2006

By Hitch M.

Many mining wastes, especially those from the metal mining industry, have traditionally been treated as a matter of little or no value and in practice a cost burden. Some wastes, due to their reactivity characteristics, have emergent values that go beyond purely economic and into the environmentally beneficial realm. This paper discusses the changing paradigm of mine waste management. Such fundamental parameters such as cut off grade, and strip ratio, are positively impacted by the revaluation of waste rock material. Mine rock waste can now be seen as a commodity of value, similar to the underlying ore being mined and influences the economic performance of suitable projects. This valuable material can be used for industrial purposes including acid neutralization as well as the capture and long-term disposal of anthropogenic carbon dioxide. The Turnagain Nickel project, located in northern British Columbia serves as an example of how waste rock material can become an important matrix for carbon capture and sequestration and can benefit economically from it. By producing material that has emergent economic value as well as carbon capture and sequestration capabilities, the sequestration matrix producer is a beneficiary of new carbon credits that have a market value and is looked upon favourably by regulatory authorities and affected stakeholders.

Jan 1, 2010

By Jon Pocock, Ashma Singh

The traditional approach for the beneficiation of South African siliceous sedimentary phosphate ores has been reverse cationic flotation. The robustness of this approach, however, has been a concern due to its sensitivity to parameters such as slimes content, headgrade ( P2O5 and SiO2 content), reagent dosages and conditioning times. The phosphate mineralisation for the ore body under investigation is predominantly carbonate fluorapatite composed of mainly quartz and apatite and minor amounts of chlorite, ilmenite and carbonates. Beneficiation of low grade sedimentary ores containing calcareous impurities, such as calcite and/or dolomite in addition to siliceous gangue, is required to meet the increasing demand; therefore, much research has been carried out to find an alternative technique to beneficiate this material. This paper investigates traditional flotation approaches versus the currently adopted ‘Crago Process’. Comparative results are presented in terms of upgrade potential for the production of concentrate rock for downstream applications. The novelty of the ‘Crago Process’ lies in its double stage approach, i.e. direct fatty acid flotation followed by reverse cationic amine flotation. The Crago process was able to achieve higher upgrades reporting at 32.1% P2O5 compared to conventional cationic flotation only achieving grades of 18.5% P2O5. Furthermore, the recovery gain was 3%.

May 13, 2023

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By D. M. Range

Exxon is reclaiming an 80 hectare (200 acre) Wyoming uranium tailings basin (10 Mt) in accordance with U.S. Nuclear Regulatory Commission requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long term reclamation maintenance was eliminated. The resulting design is similar to erosionally stable regions created by nature. The concepts used in the design and implantation have wider reclamation application.

Jan 1, 1989

By Joseph M. Chelini

The report shows the sensitivity that nine different cash-flow factors have on the discounted rate of return calculated from feasibiliity- studies on potenital open-pit orebodies of silver, copper, and uranium. Cash-flow factors of "grade", "market value", and "recovery" are. the most sensitive. This verifies the need of reliable estimates for these factors. The cost of evaluation of "preproduction cost" is the least sensitive. This gives credence to the fact that more consideration should be given to compiling sufficient data, as the largest financial losses are not in the cost of evaluation but rather in the abandonment of an unprofitable mining operation after a commitment of capital is made on the basis of an incomplete evaluation. Sensitivity analysis of cash-flow factors enhances evaluation programs by disciplining the collection of data and allowing more realistic distribution of evaluation monies.

Jan 1, 1971

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984