Search Documents

By Kathleen Kreiss, A. James Ruttenber

INTRODUCTION Early in the morning of July 16, 1979, there was a breach in the earthen retaining dam of a tailings pond at the United Nuclear Corporation's (UNC's) Church Rock uranium mill. The acidified liquid and tailings slurry spilled through the damaged portion of the retaining wall into an arroyo that is a tributary to the Rio Puerco river system. The Rio Puerco runs through Gallup, New Mexico, and eventually crosses the New Mexico-Arizona border (Fig. 1). On its way to Gallup, the Rio Puerco and its tributaries pass through land with a checkerboard pattern of ownership, with portions owned or leased by the Navajos, individuals, the Bureau of Land Management, and the State. In terms of tailings liquid volume (3.6 x 108L; 94 million gal), the UNC spill ranks as one of the largest. The mass of solids released in the slurry (10.0 x 105 kg; 1 100 tons) appears to be close to the median for accidents of this kind, however [U.S. Nuclear Regulatory Commission (NRC), 1979]. The UNC first opened its Church Rock uranium mill in 1977 on land adjacent to acreage belonging to the Navajo tribe. The mill, which is next to the UNC Church Rock mine, is located approximately 16 km (10 miles) northeast of Gallup, New Mexico (Fig. 1). Gallup, a town of 18 000 people, is the closest population center. The region surrounding the plant site is sparsely populated by Navajos, at a density of approximately 5.8 persons/km2 (15 persons/sq mile). The UNC mill and mines employ approximately 650 persons, and the adjacent Kerr-McGee uranium mine employs about 300. The UNC mill normally processes 3.2 x 106kg/day (3 500 tons/day) of uranium ore, depositing the acidified tailings slurry in a series of three earthen holding ponds. The tailings ponds are located east of the pipeline arroyo that feeds into the Rio Puerco approximately 2.4 km (1.5 miles) from the southernmost tailings dam. The liquid portion of the tailings slurry evaporates in the ponds; hence, under normal conditions, there is no surface flow from the holding ponds to the arroyo. Both runoff from the plant site after heavy rains and possible seepage from the tailings ponds may deliver radionuclides to the arroyo-river system, however. The dam across the southernmost tailings pond was considered to be in keeping with the state of the art. However, the New Mexico Environmental Improvement Division (NMEID) had warned UNC about dangers of locating the pond over a heterogeneous geological formation. The state Engineer's Office approved of the site only after UNC agreed to strict design criteria. Others have pointed to dangers of constructing earthen dams for impoundment of uranium mill tailings (Carter, 1978). Causes of the dam break were multiple: the UNC mill filled the tailings pond to a level that exceeded permit criteria; the tailings pond was lined improperly; the dam was constructed using clay that was compacted excessively, resulting in cracking and subsequent seepage; and the unstable substrate beneath the dam permitted differential settling. The UNC Church Rock mine has continuously released dewatering effluent into the pipeline arroyo at a rate of 88.3 L/sec (1 400 gal/min) since 1968. Before 1975 this effluent was not treated; after 1975 it received precipitation treatment for removal of Ra-226. Radionuclides are also released into the river system through the dewatering of the Kerr-McGee uranium mine 1.6 km (1.0 mile) north of the UNC mill. During usual mining operations, approximately 227 L/sec (3 600 gal/min) are released into the pipeline arroyo and subsequently into the Rio Puerco. The Kerr-McGee mine began continuous release of dewatering effluent in January 1972. In 1974 Kerr-McGee began Ra-226 precipitation treatment of its dewatering releases, but NMEID data indicate that treatment has often been incomplete. The effluent from both mines has been responsible for transforming the downstream portion of the Rio Puerco from a sporadically dry riverbed into a continuously flowing stream and has contributed to the current levels of background radiation along the river system (Table 1). This paper will summarize the postspill monitoring efforts and relate the assessment of this spill to the general question of evaluating the health effects of nuclear fuel-cycle wastes. The data pertaining to the measurement of radionuclides in the Church Rock environment and the radionuclide concentrations in animals will appear in forthcoming reports. CHURCH ROCK HEALTH EFFECTS ASSESSMENT APPROACH The initial health effects evaluation involved identifying the radionuclides that were released into the river system from the tailings pond. Table 1 lists the State of New Mexico maximum permissible radionuclide concentrations for liquids released to unrestricted areas, the typical tailings liquid concentrations, and postspill river water concentrations. The tailings liquid contained comparatively high levels of Th-230, Ra-226, Pb-210, and Po-210--all of which, according to postspill river water samples, had exceeded the state maximum permissible concentrations (MPC) at one time or another. After the radionuclides in the tailings were identified, pathways through which humans could be exposed were clarified. Environmental monitoring data were then used to quantify the important pathways of human exposure. Water samples were collected from the river, from test wells dug near

Jan 1, 1981

By L. Sandbak

A geomechanical rock mass classification or RMR is currently being used for the evaluation of an LHD mechanized mining system versus the conventional block caving method. The successes and failures of a Panel lS-19 LHD test block on the 2315 level can be attributed to the geologic and geomechanical zonation present. Trench blasting, caving procedures, and sequencing are other factors that were also considered. Lessons learned from the P.lS-19 test block have been used to alter the design for future LHD production blocks on the 2615 level. These modifications are designed to maximize the pillar and insure an adequate draw connection.

Jan 1, 1988

By Andrew J. Regis

Resource figures for bentonite clays are generally based on stratigraphic, sedimentary geologic data and drilling and sampling. Estimates of bentonite resources and/or reserves commonly found in the literature report on bentonite occurrences in specific localities or areas but none on any documented comprehensive estimates of bentonite resources. From 1974 thru 1977 the Bureau of Land Management conducted extensive studies of the resources of commercial grade bentonite in the three state region. These investigations consisted of: 1. Stratigraphic and geologic sampling with supplemental drilling data, followed by geostatistical analysis. 2. Data compiled from a systematic search of county and state records on mining locations, leases and acreage filed for bentonite. Estimates of resources of commercial grade bentonite using industry parameters were calculated from these data sources. It is concluded that there exists from 1.5 to 2.4 billion tons of in-place bentonite in Wyoming, Montana and South Dakota. Assuming a 5 percent annual growth rate for the industry, this would indicate a life of 62 to 73 years.

Jan 1, 1979

By James F. Holzbach

Although Disputes Review Boards have been used for some time, they had not received wide publicity at the time Monroe County first used one. Public owners frequently resist adopting new contracting practices. This paper discusses an owner's experience with Dispute Review Boards, from learning about them to their use on two (2) projects. The experiences of potential and actual contractor claims are compared to a claim on an earlier contract and the ensuing litigation. Suggestions for possible use for Owner-Engineer disputes and recommendations for use are provided.

Jan 1, 1995

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By Alistair James, Mo Shahsavari, Leon Botham

Recent catastrophic failures of heap leach facilities have revealed fundamental weaknesses in prevailing design paradigms, modeling toolkits, and oversight practices that continue to treat heaps as static, free-draining earthworks despite compelling evidence to the contrary. The core proposition advanced in this paper is that heap materials are intrinsically dynamic: their structure, permeability, and shear strength evolve under the sustained influence of irrigation, climate, and geochemical reactions, and these timedependent changes can precipitate abrupt transitions from granular stability to flow-like failure. Drawing on investigations of recent failures at Çöpler Mine in Turkey and Eagle Gold Mine in the Yukon, alongside earlier incidents in Peru, Arizona, Nevada, and Chile, the analysis identifies a recurrent sequence driving catastrophic behavior: progressive weathering elevates fines and suppresses permeability; drainage systems designed for initial conditions become overwhelmed; pore pressures rise heterogeneously within the heap; and static liquefaction initiates rapid mass movement with long runout. Current guidance, including ICOLD and ANCOLD frameworks and ASTM testing standards, provides a necessary foundation but is tailored to tailings and conventional soil mechanics. These documents offer insufficient direction for characterizing timedependent material degradation, quantifying rheology of weathered ore, and modeling post-failure mobility. To address this deficit, the paper proposes an integrated framework combining enhanced characterization, multi-physics numerical modeling that couples hydro-geochemical processes with large-deformation mechanics, and comprehensive monitoring with Trigger Action Response Plans. The conclusion argues for a heap-specific standard that embeds these elements from concept to closure, aiming to materially improve safety performance and reduce the likelihood and consequences of future failures.

Feb 22, 2026

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By P. J. Tarkoy

To successfully bid a tunneling contract by machine, a contractor must have a reliable estimate of expected penetration rates and cutter costs. Preferably, these predictions should be independent of those supplied by machine and cutter manufacturers. Therefore, a series of rock index tests have been developed and incorporated in routine Rock Mechanics testing for the purpose of predicting rock boreability. Index properties were evaluated empirically by using rock samples and pertinent construction records from recently machined tunnels. Samples were taken from the completed tunnel walls, tested parallel to machine penetration, and results were compared to localized rates of penetration. Indices are based on two measures of rebound hardness and two measures of abrasive properties. The Shore (C-2 type) Scleroscope and Schmidt (L-type) Hammer were utilized to measure rebound hardness and a Taber Abraser was modified to measure rock abrasiveness and abradeability. Results indicate that rock hardness index properties investigated in this study can be used successfully to predict TBM penetration rates.

Jan 1, 1974

By P. Anciaux, T. Simpson

The competitiveness of the EU manufacturing industry has come to the forefront of EU politics. The systematic monitoring of developments and the review of the state of the competitiveness of economies and enterprises was identified as an essential component in this process. Work is currently being carried out within Enterprise and Industry Directorate-General in order to analyse the different factors that influence the competitiveness of the non-energy extractive industry. Such an assessment should help to identify policies and actions which could contribute to and enhance the competitiveness of the industry. Assessing the competitiveness and sustainability of the industry implies the need for reliable, consistent data. One important example of how this need is being addressed, is the development of sustainable development indicators (SDI) for the EU non-energy extractive industry. These seek to monitor the industry’s performance and provide a platform for openness and discussion. Work was started on the development of SDIs in 2000, and the first report was published in February 2004.

Jan 1, 2005

By V. V. Ershov

Mining geometrical graphic documentation is employed on a large scale in designing and planning of mining operations at all the stages of exploitation. Mining geometrical modelling of mineral grade distribution presents an independent type of mathematical (graphic) modelling. The idea of functional relationship between geological indices being observed, and spicier coordinates is the basis of traditional mining geometrical modelling. Graphic presentation of three independent variables P =f (x,y,z) is confined to obtaining the series of two independent variables functions. Independent variables are presented as topographic surfaces corresponding to plane cross-sections of a deposit. During exploitation of certain parts of a deposit the most reliable geological information is obtained, characterizing regularities of ore distribution in the entrails. This information is, though, not taken into account in goemetrization of the new areas. In this connection dynamic modelling of deposits in the process of exploitation is necessary, i.e. geometrization of the deposits should be dynamic.

Jan 1, 1986

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979

By P. Ritsopoulos, A. J. Dentsoras

The objective of this paper is the development of a reliable simulation model for the operation and production capacity of an aggregates quarry. Based on this model, a computer program is introduced that provides the final production outputs according to the defined material gradation and machinery characteristics. The program takes into consideration all operational parameters that may be introduced by the user through the whole machinery network. As a result, all production parameters are properly updated. The structured simulation program can help detect production inefficiencies that result from design ineffectiveness. Additionally, the program can be used for the generation of alternative scenarios for future modifications of a plant's configuration. Finally, a designer can use it as a tool for obtaining optimum solutions concerning newly designed quarries. As a case study, a quarry operating at Heraklion, Crete, was examined. The application of the program to the plant produced a complete image of the quarry's input/output characteristics, along with some suggestions for improvements on certain production processes.

Jan 1, 1998

By Mark J. Schultz, William J. Francart, Gary J. Wirth

Atmospheric Monitoring Systems (AMS) utilizing carbon monoxide sensors have demonstrated their superiority over thermal type fire sensors for early fire detection in underground coal mines. After proving their capability and dependability throughout the 1980's, systems are now evolving and applying new technologies to enhance their effectiveness and reliability. The use of AMS in coal mines which utilize diesel equipment presents unique obstacles. Exhaust gases from diesel equipment not only raise mine ambient CO readings, but also cause numerous nuisance alarms. Both of these conditions reduce the effectiveness of the AMS. New technologies, such as discriminating devices, smoke detectors, and time delays, as well as administrative controls, have been developed and are being utilized to help reduce nuisance alarms produced by the diesel exhaust. This paper will discuss these technologies and administrative controls which are being utilized in coal mines to enhance the effectiveness of the Atmospheric Monitoring Systems. Reference to specific products does not imply endorsement by the Mine Safety and Health Administration.

Jan 1, 1995

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By Murali M. Gadde, Syd S. Peng, C. T. Holland

Cutter roof failure is one of the most common ground control problems affecting the safety and economy of an underground coal mine operation. Several attempts were made in the past to understand the processes responsible for cutter development and to devise mitigating measures. Yet, many cutter failures still happen and their advance prediction remains as elusive as before. One of the reasons for the impasse in predicting cutters lies in the limitations of the current numerical modeling technologies. The development and propagation of cutters is a progressive phenomenon and continuum models can only approximate this process. Since the discontinuum modeling is severely restricted by the lack of reliable input data, alternatives must be sought to better understand cutter failures using the continuum models. This paper proposes one approach using strain-softening material model to simulate the cutter initiation and propagation process. An attempt has also been made to provide some insights into the reasons for the change in cutter location at different parts of a development layout.

Jan 1, 2005

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By Charles D. Litton, Margaret R. Egan

In order to reduce the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Welding and cutting with arc or flame can also produce combustion products capable of triggering nuisance alarms. In this report, the response of the DDD to the emissions from diesel exhaust, arc welding, and flame cutting are compared to the response of conventional smoke and carbon monoxide (CO) detectors. The data show that when the DDD is set at an alarm threshold of 0.05 v, it will reliably detect a developing conveyor belt fire while remaining insensitive to other sources of nuisance combustion products. The alarm times of the three types of detectors were also compared. The DDD alarmed first in response to a smoldering conveyor belt in two of four experiments.

Jan 1, 1992