Search Documents

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By Steve Kral

For an industry that provides more than half of the nation’s energy needs, the U.S. coal industry still attracts negative publicity. However, the nation’s energy appetite continues to increase. And political leaders and the public are beginning to understand that alternative fuels will not be enough to keep up with that appetite. Does that mean the nation will now embrace the coal industry? No, according to speakers at the Rocky Mountain Coal Mining Institute (RMCMI) meeting. The industry still needs to sell the public on coal’s advantages over other fuels. And the industry must continue to develop technology that will allow coal to meet and exceed strict clean air and clean water regulations.

Jan 1, 2002

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Mark E. Smith, Gerald J. Gierszewski

Introduction The purpose of this paper is to present a procedure used by the authors for evaluating and designing soil liner systems. This method is particularly valuable in evaluating various treatment schemes for chemically amended soil liners. A tabulation of laboratory test results on various soil types are presented to quantify the effectiveness of certain treatments. A typical liner design program includes developing and proving soil borrow sources, designing the cross-section of the liner system, developing construction specifications, and providing construction services to ensure the intended product is achieved. Material Source Development The first step in designing a soil liner is to identify and evaluate suitable borrow sources within an economical haulage range. This is best done in a two step approach: a reconnaissance level investigation to identify target areas and a detailed evaluation of those targets. Reconnaissance: The goal of the preliminary investigation is to locate potential borrow sources for liner quality soils. This includes all natural materials which can be compacted, chemically treated, or otherwise amended to yield an installed permeability at or below some target value. This requires utilization of all available data sources: Soil Conservation Service, BLM, aerial photos, USGS geologic maps, and project geologist records. The goal at this stage is to locate shallow deposits of favorable soil types. The Unified Soil Classification System provides an excellent first pass grouping. Clays, clayey sands and silts are the most favorable soil types, although silty sands and occasionally clayey gravels can make excellent liners, and are often amenable to chemical modification. The lowest permeabilities are generally achieved with CH, CL and MH soils. Once preliminary targets have been identified using visual examination, laboratory classification tests should be performed to further refine the selection. Testing at this stage should include gradation, plasticity and hydrometer analyses. Additionally, "preg-rob" testing should be done as early as practical. Preg-rob is a phenomenon where gold or silver ions in solution associate with the clay, or other, minerals. When this occurs, a portion of the gold or silver leached from the ore is actually tied-up by the clay and thus a reduces recovery. Testing for this consists of agitating a small sample of the soil in a solution containing dissolved gold or silver, preferably of similar chemical make-up as the solution which will contact the actual liner. The solution and soil are assayed before and after agitation to determine loss to the clay. A reliable estimate of the hydraulic conductivity, commonly referred to as permeability, can be developed from the D10 value by the use of Hezen's formula: K = 100 (D1012 This relationship is limited to soils where the finer particles do not move due to the force of flowing water (i.e.: "hydrodynamic stabilitym)(1). Additionally, the effect of platty particles on permeability is not as predictable as the effect of equidimensional particles. D10 is the sieve opening size at which 10% of the material is finer. Plasticity is also important from several standpoints. Constructability is directly related to plasticity. Very plastic clays and non-plastic silts both tend to be difficult soils, while medium plastic clays and clayey sands are generally very desirable. Post construction performance is also related to plasticity (e.g. swelling, shrinkage cracking, frost heave, etc.). Additionally, low plasticity silts and silty sands generally do not respond well to chemical amendment. Source Development: The result of the reconnaissance evaluation should be an estimate of the relative probability of developing a suitable borrow source within an economical haul distance. Of course, "economical distance" depends on the degree of handling and treatment the borrow material requires, as well as the cost of synthetic alternatives. The purpose of the detailed investigation is to prove out quantity and quality of material sources, and determine design parameters such as degree of compaction, mixing, treatment and thickness of liner. The emphasis of the testing program should be permeability and strength. Strength becomes increasingly important as the slope of the liner and the height of the heap increase. Permeability testing should evaluate the effects of compaction, water content, mixing and chemical treatment where appropriate. The effects compaction and water content during compaction have on

Jan 1, 1987

By G. T. Lineberry, W. J. Wiehagen

A paradigm shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results can invoke questions such as how much was produced, at what cost, and was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as pre-eminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured and formed new coalitions. Investments in new technology and a concentration on productivity have been an essential part of these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. This situation presents an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now night offer some interesting opportunities for the Future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work Force. The Work Crew Performance Model (WCPM) is one approach to defining, capturing and transferring this expertise. The WCPM suggests a paradigm shift, moving from a focus on products (quantity) to a focus on the process (quality). It also involves a slight change in the process -- a different way to think and work. Of great importance, it entails a belief and a commitment to people within the organization; a commitment to collect simple (but interesting) data; exploration for insightful ways to plot and integrate that data; and finally the search for creative methods to reinvest that knowledge back into the organization, that is, back into the work force. As a way of thinking, the WCPM subordinates information about how much is produced daily or how many were injured over a year's time to concern and detail for how the individual's and the work crew's performance contribute toward meeting organizational goals. Drawing upon the expertise within members of that work crew to address and solve operational problems is one approach for meeting organizational goals. This everyday focus on how we work is hypothesized by the WCPM to make the difference between a good section supervisor and the average one; an exemplar continuous-miner operator and the run-of-the-mill one; a mining crew that produces consistently high quantities, but, inadvertently, degrades the production of other units. The WCPM permits objective and reliable performance data to be collected. This data then can be used to define variability within tasks of work crew members; to relate observed variability to a cost consequence; and to more meaningfully analyze performance through the integration of traditional analytical tools, such as the production simulator, CONSIM, with a recommended behavioral approach, the WCPM. Basis for engineering test Most equipment selections and purchases involve a field trial test of the system. Technology is routinely bench tested at the manufacturer's facility, government agencies and the mine site. The WCPM suggests a similar, but more practical, method for testing the performance of a work system -a test for how technology is used (by people) at the work site. It implies learning from veteran mining personnel that have gone well "beyond the book." This approach to learning and to integrating training with everyday work life can help answer questions such as: What constitutes desirable perfor¬mance as, for examples, a shuttle-car operator, a miner operator or a bulldozer operator; what characterizes exem¬plary performance within the context of the work system, the technology and the work crew; how can investments in the worker he linked to measurable results within the organiza¬tion? This paper explores these questions and makes recom¬mendations for enhancing the cost-linkages between invest¬ments in people and the mine's monthly cost sheets.

Jan 1, 1996

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986

By R. Benito

This paper describes the development of a life of mine schedule (LOM) for one of the world?s largest known sedimentary Copper-Cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity constrained process facility. This paper discusses the main scheduling objectives and constraints, data pre-processing as a scheduling aid, the mine scheduling approach, and results and conclusions.

Jan 1, 2011

By Fred Leighton

Miners have long known that rock noise, or the popping and cracking of the rock commonly heard during mining, can indicate instability of the mine structure. For many years, miners have "listened" to the rock talk and many times have interpreted changes in rock noise activity to be a warning of failure and have retreated from the potential failure area. Microseismics, or the study of rock noises, was begun in the early 1940s partly because of this historical fact. Microseismics is based on using geophysical equipment to detect and analyze rock noises on audible and subaudible levels. Thus, these systems are much more sensitive than the human ear and "hear" even more of the rock "talk" than do miners. Research has shown that micro-seismics can be used to precisely locate portions of a working area that are generating rock noise, and that rock noise release rate information from each area can be used to analyze its stability. On the basis of research results, microseismic systems are now commercially available and have been purchased and installed in many mines around the world. Introduction When a rock mass is subjected to changing stress conditions, such as those caused by mining, small-scale adjustments occur within the rock that release seismic energy. When this energy is in the audible range it is called rock noise. Those areas where stress changes occur are also the areas of the structure most likely to fail. Individual rock noises can be detected and analyzed to determine their precise location relative to the mine structure. Over a period of time plots of this data provide a pictorial representation of where stress changes are occurring. This is because rock noise activity tends to concentrate in those structure areas most actively adjusting to the changing stresses. Since these areas are the most likely to fail, they can be pinpointed and mapped relative to the structure. Rock noise rates, or the number of rock noises occurring per unit of time, also tend to vary dramatically before failure. Thus, the ability to locate the source of individual rock noises provides a means of determining where failure may occur, and rate counting within each area offers a means of assessing when failure may occur. This information, properly treated, can be used to avoid, control, or warn of impending failure. Successful applications of this technique have provided recent impetus to the effort of developing microseismics into a practical, reliable, and economically feasible tool. The phenomenon of naturally occurring rock noise was discovered in 1938 by Obert and Duvall (1939) who were measuring seismic velocities in mine pillars. Seismic energy other than what they were generating continually registered on their recording equipment. Further study by these researchers showed that the extraneous seismic energy being recorded was from rock noises that were being generated within the rock in highly stressed areas. Pursuing this interesting phenomena both in the laboratory and in the field, Obert and Duvall documented the dramatic change in rock noise rate before failure (Obert, 1941). They also established the fact that, in many instances, rock burst failures could be predicted by monitoring and listening to the rock noise activity in rock-burst-prone areas (Obert and Duvall, 1945). These early efforts clearly showed that microseismics had great potential as a tool for measuring or estimating mine structure stability. Extended testing, however, showed that sometimes rock bursts occurred with no apparent microseismic warning, and that at other times sharp increases in microseismic data were not accompanied by failure. Also, because precise location of individual rock noises was not possible at that time, one never knew where the failure was going to occur, only that failure near the observation point was likely. Thus, while the technique clearly offered promise, it was not considered practical then. In the mid-1960s, the Bureau of Mines undertook a new research effort to improve the microseismic technique. Major improvements were judged possible mainly because new and vastly improved electronic and system components had become available as an offshoot of space program instrument development. Thus, in 1967, development of a multichannel, broad band, microseismic system began (Blake and Leighton, 1970). Application of this system in rock-burst-prone mines showed it worked well and provided the incentive to develop methods whereby the source location of individual rock noises could be easily and directly calculated (Leighton and Blake, 1970; Leighton and Duvall, 1972; Redfern and Munson, 1982). The improved system and the ability to locate rock noises quickly showed that the microseismic technique offered new and increased poten-

Jan 8, 1983

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By Henry S. Brown

At least two dozen massive sulfide deposits in the southern Appalachians have supported significant mining operations. Literally hundreds more deposits are known to exist, but are too small to be of commercial interest. Essentially all that are being, or have been, mined are those deposits that were exposed at the surface when first discovered. It is reasonable to assume that many more massive sulfide deposits, large and small, exist hidden not far beneath the surface. The ideas I am sharing with you here today are based both on my personal studies of some of the deposits and on descriptions of deposits in the literature. An attempt will be made to account for the genetic interpretation problems raised by many of these deposits posessing both "syngenetic" and "epigenetic" features. In addition, an examination will be made of the possible relationships between the massive and the not-so-massive sulfide deposits in this region. Hopefully, these observations added to those of others will eventually lead to the synthesis of a better model on which we can base exploration programs in the southern Appalachians.

Jan 1, 1976

By David Van Horsen

Operation and maintenance of California?s water tunnels is an important factor and vital link in California?s infrastructure. These tunnels are owned and operated by a variety of large and small private and public water and power utility companies, municipal agencies, and irrigation districts. Visionary pioneers such as Michael O?Shaughnessy (San Francisco Hetch Hetchy Water Supply System), William Mulholland (Los Angeles Department of Water and Power and Metropolitan Water District of Southern California?s Colorado River Aqueduct), and John Eastwood (Southern California Edison Big Creek Hydroelectric Project) built large and small water supply, irrigation and hydroelectric tunnels, which have supplied environmentally friendly-water supply, renewable electricity, and uninterrupted service to a burgeoning population and economy. This paper introduces these pioneers and describes several case histories and lessons learned during condition assessment and rehabilitation of tunnels providing enlightenment of California?s vital water projects.

Jan 1, 2008

By K. Avarmaa, P. Taskinen

"The solubilities of rhodium (Rh) in a molten silver alloy in doré-smelting conditions for treating copper refinery slime at temperatures of 1,000 to 1,300 °C were measured using a high-temperature equilibration-quenching technique and direct phase analysis by electron probe X-ray microanalysis. The results obtained indicate that the solubility of rhodium in molten silver is very limited: only 0.04 to 0.26 weight percent at 1,000 and 1,300 °C, respectively. The thermodynamic properties of rhodium in molten silver were estimated from the solubility data. The compositions of the solid rhodium alloys in equilibrium with molten silver-rich doré metal were also measured in this study. The excess rhodium in the doré alloy will precipitate during the refining as solid, greater than 99 weight percent Rh.IntroductionSilver refining is a core step of the processes of anode slime treatment and precious metals recovery in copper refineries (Hait, Jana and Sanyal, 2009; Ludvigsson and Larsson, 2003). It separates the oxidic materials, such as nickel oxide (NiO) and barium sulfate (BaSO4), from metallics after the de-coppering and de-selenation steps of the anode slime, and refines the silver bullion from the undesired elements present (Cooper, 1990; Hyvärinen, Lindroos and Yllö, 1989). Doré metal is a silver-rich alloy which after the smelting step will be refined electrolytically, and the remaining constituents of gold as well as the platinum group metals (PGM) will be subsequently recovered in their own processing stages.Because of low concentrations of PGMs in copper, they are typically soluble in the doré metal in anode slime treatment. This can be concluded from their binary phase diagram data with silver (Massalski et al., 2007). One exception is sometimes encountered in the anode slime smelting operations if the smelter feedstock is rich in rhodium, as may be the case if the raw materials contain secondary raw materials such as e-scrap. The solubility of rhodium in solid silver is less than 0.04 weight percent (Królas and Sternik, 1995), and its solubility in molten silver is highly uncertain. The only experimental information in the literature (Królas et al., 1993; Elliott, 1985) suggests that the silver-rhodium alloy system at 960 °C forms a eutectic, which locates less than 2 °C below the melting point of pure silver (Arblaster, 2015). Early observations (Rössler, 1900) propose that rhodium is insoluble in molten silver even if solid silver-rhodium solutions have been recently produced on a nanoscale (Kusada et al., 2010).The aim of this study is to measure experimentally the solubility of rhodium in molten silver at doré metal smelting and refining temperatures. The silver alloy used to mimic the doré alloy contained silver and about 1 weight percent of the alloying elements copper, gold, palladium, rhodium and tellurium. The experiments were carried out in metal-slag equilibria with nitrogen-oxygen mixtures as the atmosphere, employing an equilibration-quenching technique and using direct phase composition analysis by electron probe X-ray microanalysis (EPMA) (Jak, Hayes and Lee, 1995)."

Jan 1, 2017

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By John M. Smith

Kaolin is an important industrial mineral because of its unique properties and low cost. Strictly defined, kaolin is the name given to a group of hydrous aluminum silicates of which kaolinite is the most common mineral (1). Through common usage the mineral, kaolinite, is called "kaolin" or "china clay". In 1972 over 4, 000, 000 tons of kaolin will be beneficiated and shipped by domestic producers. By far the largest user of kaolin is the paper industry which utilizes approximately 65 to 70 per cent of the total production. Kaolin is used in paper as a filler in the interstices of the sheet and as a coating to impart smoothness, gloss, brightness, and printability to the paper. The rubber industry is also a large user of kaolin where it is used as a filler because it adds strength, abrasion resistance, and rigidity to both natural and synthetic rubber goods. Kaolin is used as an extender in paints because it is chemically inert, has a high covering power, gives desirable flow properties, and is low in cost. In ceramics, kaolin is used in whitewares, tile, insulators, refractories, and in some face brick where a white color is desired. Kaolin is also used extensively in plastics as a filler in thermosetting and thermoplastic mixes to give smoother surfaces, a more attractive finish, good dimensional stability, and resistance to chemical attack. Many other process industries use kaolin as a filler, suspending medium, or for color improvement.

Jan 1, 1972

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By J. C. Yingling, R. J. Sweigard, S. T. Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty inherent in the factor-of-safety (FS) predictions for soil slopes in which there is an incomplete knowledge of the spatial distribution of soil properties. A case study that considers a natural clay slope in Canada is presented. The sequential-indicator simulation technique was used as a means of generating a series of spatial maps of the soil properties at the site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. FS determinations were made for each simulated map using the simplified-Janbu approach. In using this approach, computations are performed using a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the FS distribution conditional to the type, position and value of existing site-characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1996