Search Documents

By K. Galos

The paper presents increasing importance of mineral secondary and waste raw materials in the minerals management in Poland. Definition of mineral secondary and waste raw materials is proposed, according to current Polish law. On this basis, sources of various types of mineral waste raw materials are analysed. The special attention is paid to the wastes from mining and processing, wastes from power plants, and wastes from steelworks and other smelters. Other types of waste and secondary materials, such as metallic containers, glass containers, batteries, metallic wastes and scraps, are also taken into account. Analysis of sources of such materials is shown together with the main directions of their economic use. Available sources of information on manufacture and use of the mentioned secondary and waste raw materials are also analysed. Finally, for a wide range of waste materials, their current and expected significance as substitutes for some industrial and construction minerals in Poland is given.

Jan 1, 2011

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

By J. F. Brune

This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Although direct examinations of the gob atmosphere are difficult due to the inaccessibility of these gobs, evidence from methane drainage practices and investigations of numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners. Most recently, this was demonstrated in the explosion of the Upper Big Branch Mine in West Virginia, where 29 miners lost their lives.The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions, along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Jan 1, 2013

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By R. H. Derammelaere

With renewed interest in coal slurry pipelines in China, Indonesia, Australia and Canada for electric generation, it appears worthwhile to update the relative economics of transporting coal by slurry pipeline. Three slurry pipeline technologies are evaluated for the commercial transportation of 3.0, 6.0, and 9.0 million tonnes per year (MMT A) example cases, over distances of 250 km, 500 km and 1000 km.

Jan 1, 1998

By Paul R. Smith

The theoretical requirements for the flotation d large particles are discussed. A flotation machine is described which has components which meet many of the theoretical requirements for the flotation of large particles. The machine's salient features include multiple fine-bubble attachment, froth level feeding, quiescence, shallow depth, and short flotation time. Test conditions and results are presented for the laboratory flotation of 10 mesh phosphate, 4 mesh potash, and 1/2 inch coal. In addition, test conditions and results of pilot plant flotation of minus 14 plus 35 mesh phosphate and minus 14 plus 150 mesh phosphate are also presented.

Jan 1, 1969

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By W. Ellison

Worldwide development of commercial markets for FGD (flue gas desulfurization) gypsum is described and used as a basis for assessing potential overall market growth and regional demand foreseen in the U.S. during the 1990s. Diverse strategies are outlined for cost-effective substitution of this major supply from acid rain control retrofits (power plant scrubbers) for natural gypsum in the principal, existing markets: gypsum board and portland cement. Another focus of utilization forecasting is a key group of related. new-product advancements including floor screeds, mining mortars and various types of innovative construction products.

Jan 1, 1993

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

By J. M. Keane

SMEThis loaner is concerned with important criteria relative to the design of small flota¬tion concentrators. For the purpose of this discussion a small flotation concentrator is defined as a facility having a designed ore feed rate of 1,000 metric tons per day (MTPD), or less. The decision to design and construct a small flotation concentrator is the culmination of a series of logical steps relative to the ex¬ploitation of a potential ore body. The information required for a rational and timely decision regarding plant design and construction is usually contained in a feasibility report. The information required in a thorough feasibility report has been summarized (1) (2) as follows: Type of mine or plant and proposed daily, monthly, and yearly production of all intermediate and final products. Quantity of indicated ore reserves. Location of project illustrated by a map showing surroundings, trans-portation facilities, and existing utilities.

Jan 1, 1980

By Warren D. Stanford Stanford

Introduction The Sleeper mine is a near-surface gold mine located in a remote area 56 km (35 air miles) northwest of Winnemucca, NV (Fig. 1). The deposit was discovered in 1984 by an Amax exploration geologist. Favorable drilling results led to feasibility studies and metallurgical testwork. Final evaluation of the mine potential proceeded very quickly. The project received Amax board approval in July 1985. Eight months later, the process plant was fully operational. The first gold ($1 million) was shipped one month later, in March 1986. Total plant capital was $27 million. Payback was achieved in six months. The Sleeper mine was expected to produce 1.6 t (53,000 oz) of gold and 1.3 t (41,000 oz) of silver annually. However, the ore body exceeded all expectations. Production for the first 10 months of operation amounted to 4 t (128,000 oz) of gold and 2.9 t (94,000 oz) of silver. Direct cash operating costs are in the $1.77/g ($55 per oz) range. Amax is actively conducting exploration nearby for additional reserves to extend the mine's life. (See update on page 242.) Geology The Sleeper gold deposit is located on the northwestern flank of the Slumbering Hills and in the Awakening Mining District. Rocks exposed in the vicinity of the deposit are interbedded siltstones, sandstones, and limestones of Triassic age. They are overlain by latite lava flows and tuffs of Tertiary age. Dikes and sills of latite and andesite intrude the sedimentary rocks. Quaternary deposits of mostly sand with minor gravel and clay cover a pediment containing the gold deposit. The sedimentary and volcanic rock units have been transsected and offset by extensive north- northeast trending faults and less abundant northwest trending faults. Both fault systems fractured and prepared the ground for subsequent invasions of mineral-bearing hot spring geothermal waters. The hot spring systems produced widespread hydrothermal alteration and gold mineralization at silicified centers near feeder fault structures. The deposit is hosted by siltstone and latite that have been hydrothermally brecciated. The main breccia is elongated north-northeasterly. The hydrothermal breccia zones appear to dip steeply to the west. Gold mineralization consists of native gold and electrum deposited in two or more high-grade quartz-breccia veins. Lower grade gold mineralization occurs

Jan 4, 1987

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By R. J. Sandberg

The Copper Creek area, part of the Bunker Hill District, Pinal County, Arizona, lies within the southwest porphyry copper province of North America at the intersection of a northwest trend and an east-northeast trend of Laramide porphyry copper deposits. The Copper Creek area has been mined and explored for copper and molybdenum since the early 1900?s. The majority of this work focused on the more than 400 surface exposed breccia bodies. In the 1960 to 1970?s deeper drilling discovered a deep porphyry copper-like setting. Redhawk Copper currently has NI 43-101 compliant resources of about 0.652 billion pounds of measured and indicated and 2.745 billion pounds of inferred copper equivalent in breccia hosted and porphyry style deposits. See Figure 1.

Jan 1, 2010

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986