Search Documents

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

By R. D. Rein

The Henderson mine is a large continuous panel caving operation in central Colorado. The orebody is roughly 760 m by 910 m and will be extracted from two production levels. Each level is divided into three north - south panels 244 m to 317 m wide. The general arrangement of a production level and its associated undercut drifts is shown in Figure 1. The production drifts (3.6 m by 3.7 m) are spaced 24 m apart center to center and have undercut drifts (3.4 m by 3.8 m) 17 m directly above them. The production drifts are interconnected with drawpoint crosscuts (4 m by 4.3 m) driven on 12 m centers. Drawpoint crosscuts receive substantial brow steel and concrete support prior to undercutting. The brow steel is a 15 cm by 46 cm wide flange beam with a 2.5 cm wear plate to box in the 'cave' side of the beam. The concrete is a minimum of 0.3 m thick and the batch design results in 27 500 kPa strength. The finished drawpoint opening is 3.7 m by 3.2 m with a choke area of 3.7 m by 2.4 m. (Figure la) Undercutting and bell formation is accomplished by blasting rings of 7.6 cm holes drilled from the undercut drifts. The rings have a burden of 2.0 m and six rings develop one complete bell.

Jan 1, 1985

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine, or for the expansion of an existing mine, can range between 9 months to 24 months, or more. The time frame will vary depending on whether an Environmental Assessment (EA) or an Environmental Impact Statement (EIS) will be completed. Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. The two year natural resource baseline study completed by Homestake Mining Company for the Ruby Hill Mine, located in Eureka County, Nevada will be used as the case study to describe how properly designed and executed natural resource baseline studies streamlined the NEPA process.

Jan 1, 2001

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By Niles E. Grosvenor

Several methods have been proposed for determining the tensile strength of rock. These have been tried out over the past several years, but the results have been erratic and of doubtful value. The tensile strength of rock is its weakest property, and this property apparently enters into all failure phenomena whether underground or on the slope of an open pit. Therefore, it is essential that detailed quantitative information is known about the tensile strength of rock if the design engineer is going to select the proper pit' slope, pit orientation, or orientation of underground workings so as to give the most economical and safest mining condition. This quantitative information may be used to orient the pit in such a manner as to allow steep slopes along two sides. This information may possibly be used to orient the direction of either underground workings or open pits so as to decrease powder consumption and to increase blasting efficiency. Hence it is of prime importance that a method of determining accurately the tensile strength of rocks be developed.

Jan 1, 1960

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By J. T. Ryan, Griffin. Wayne H.

This paper shows that if a drift has a brattice which is sufficiently leaky, changes in the operating point of the fan depend solely on the volumetric efficiency within the drift. Under this high leakage condition, an increase in the length of the drift causes very little shift in the fan operating point. For less leaky brattices, the operating point depends on both the fan characteristic curve and the volumetric efficiency. It is shown that for the fan curve and drift parameters used in this paper the fan operating point in a drift with a volumetric efficiency of 50% is essentially the same as a drift which has a zero efficiency. In this region of efficiency, an increase of 300% in the length of the drift causes only a 3% increase in fan operating pressure.

Jan 1, 1993

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

By Carl C. Martin

The treatment of ores in preparation for fatty acid flotation is characterized by a wide divergence in methods, and attempts to define "common practice", even for the same type of mineral, are usually of little value because of the numerous exceptions. Such factors as desliming, pulp density, pulp temperatures, and reagents for conditioning are successfully employed under conditions representing almost extreme opposites. More precise control of variables is necessary than with sulphydric flotation processes It appears likely that variations result from independent development of a process from the multitude of variables that characterize fatty acid flotation and the ores of non-metallic minerals. Consequently, a symposium is a suitable way of presenting a summary of pretreatment methods for fatty acid flotation processes, together with froth control practices, as they exist today.

Jan 1, 1959

By H. L. Hinds

Economic pressures to increase production to profitable levels reduced the Homestake's gravity recovery and overall recovery to un-acceptable levels. The operation of the Home-stake gravity gold circuit has increased gravity gold recovery to over 50%, improved overall recovery and increased mill availability for increased tonnage. The gravity circuit consists of three gravity gold recovery stages. The Circuit has four (4) duplex jigs, four (4) belt concentrating strakes and four (4) concentrating tables.

Jan 1, 1989

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981