Search Documents

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

By Ian McFeat-Smith, Robert J. Fowell

Roadheader machines have a specific place in modern tunnelling, not simply as a compromise between drill and blast techniques and full face machines, but as an economic and versatile form of mechanised tunnelling where the method of excavation is easily integrated with tunnelling operations. In the past, roadheaders have been subjected to misuses by engineers who failed to realise that, as in all mechanised tunnelling, a planned and systematic approach is essential if the full potential of these machines is to be gained. An increasing awareness of this, together with the introduction of the more powerful roadheader carrying their cutting potential into the hard range of rock is changing this situation and now makes the prospect of using roadheaders particularly attractive (1). The advantages gained by employing these machines can be considerable and Table 1 lists some of them. This table illustrates that from both cost, and installation points of view, the roadheader has considerable benefits over the full face machine. However, the principal advantage gained is in broken ground where heavy supports can be installed immediately at the tunnel face. In addition, access for planned maintenance and repairs to most working parts of the machine is at a premium and average machine utilisations of 40 - 60% can be expected. In comparison to drill and blast methods, up to 40% better progress can be regularly achieved, and the subsequent savings in overbreak costs alone would more than pay for the cost of a roadheader used to drive a 3km long tunnel. As with full face machines, ground disturbance is minimal and for short tunnels in urban areas a road-

Jan 1, 1979

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels - from mining and processing to the manufacturing of finished products. In 2010, the estimated real GDP of the United States increased by 2.8 percent compared with 2009 and the estimated nominal GDP was about $14.6 trillion (Table 1).Trends in various sectors of the domestic economy are often rejected in mineral production and consumption rates. For instance, continued declines in the construction industry during 2010 were rejected in further reductions in the production and consumption of cement, construction sand and gravel, crushed stone and gypsum, which are used almost exclusively in construction. Performances in other sectors were mixed and less easily characterized. Recovery from the economic decline of 2008-2009 became apparent in 2010, as prices for many mineral commodities continued to rise with increasing demand for those materials or the products in which they are found.

Jan 1, 2011

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By R. E. Greuer

The design of mine fire emergency plans requires that the contamination of mines by fumes, and the mutual interaction of fires and ventilation systems be pre-calculated. Several computer models were developed by the Bureau of Mines for this purpose during the last decade. The models advanced in sophistication from the transient-state simulation of fume concentrations for the early stages of a fire to the steady-state simulation of airflow rates, concentrations, and temperatures for fully developed fires, and finally to the complete transient-state simulation of fires and ventilation systems. The principal features of these models are described.

Jan 1, 1989

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and 'weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

By T. Yukimasa

Hachinohe smelter, a zinc-lead blast furnace complex with the annual capacity of zinc plus lead of 100,000 tons, had originally treated normal zinc and lead sulfide concentrates. However, it is currently handling a great variety of raw feeds ranging from complex sulfides to oxidic recycled materials in view of resource economy, most of which are unsuitable for zinc electrolysis. This paper reports on some significant efforts recently carried out on improving sintering operation, i.e., the increasing use of secondaries against harmful ingredients like halogens, and the substantial reduction in energy use as the results of various modifications and improvements.

Jan 1, 1982

By Charles H. Grant

Communications in whatever we do, is one of the major problems we encounter. In an effort to provide a better understanding of the use of explosives, I am going to take a little different view of what explosives are, and how you might look at them as tools to fragment rock, and some of the problems encountered in doing so. First, let's take the explosive, and although there are many factors involved, I want you to consider these as being reduced to only two--shock strain imparted to the rock by the high early development of energy; and the other, the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc..

Jan 1, 1968

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By Brenda B. Mehnert

Long-term monitoring is necessary to successfully develop predictive subsidence models. Thus, the Illinois Mine Subsidence Research Program (IMSRP) has documented subsidence over a longwall mine in south-central Illinois throughout a 3-year period. No monitoring results of this duration have been previously published for longwall mining in Illinois. To study the effects of surface subsidence and the rate of subsidence, precise level surveying was conducted at the site two or three times a year. Level surveys were conducted at approximately the same time of year using a WILD NA-2 level with a micrometer. Second-Order, Class-I, closure errors were obtained in each survey. Survey monuments were designed to minimize frost-induced movements. At this particular site in southern Illinois, subsidence over chain pillars and the panel centerline continued 3 years after mining. Since mining in 1988, 6.67 feet of subsidence or 70% of the extracted height has been documented over the panel centerline, with almost 0.30 feet in the last two years. The area over the chain pillars has subsided a total of 1.44 feet, with 0.44 feet occurring within the last 2 years. Monitoring over the chain pillars and at the centerline shows the residual subsidence to be fairly uniform. Monitoring is continuing over both of these areas. Long-term monitoring data can be used to improve evaluation of subsidence effects on land and structures. However, coal companies will time mitigation activities depending on other factors including the threshold of structural damage, type of repair needed, and maintenance of landowner and company relations.

Jan 1, 1986

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011