Search Documents

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By J. David Lowell

The discovery of the Kalamazoo (Arizona) ore body was a comedy of errors and coincidences and luck -as most discoveries probably are. The story began in early 1965 when Quintana Petroleum decided to diversify from petroleum into minerals and decided to do this by the route of minerals exploration. Quintana Petroleum is owned by the Cullen family of Houston and has Geen successful over the years in discovering oilfields. In 1965, the president and general manager was Corbin J. Robertson, son-in-law of Harry Cullen, founder of the company and a famous Texas wildcatter. But, in 1965, Quintana's financial advisors suggested that the company go into several mineral commodities, including copper, with Tucson, AZ, as the jumping-off point for copper exploration, and with a geological consultant (me) as the point man. The stage was now set! (See Fig. 1, location map of the San Manuel District, Arizona.)

Jan 1, 1991

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By H. Do

In flotation, hydrophobic particles are selectively collected by air bubbles, and the bubble-particle aggregates enter the froth phase. However, less hydrophobic particles drop off from the froth phase, while more hydrophobic particles are recovered. Thus, the froth phase provides an important cleaning mechanism. In the present communication, the froth-phase recovery process has been modeled by considering particle retention times and the carrying capacities of bubbles. The model predictions are compared with the experimental data reported by Seaman et al. (2006). The results show that the froth-phase recovery varies with particle size, particle hydrophobicity, and bubble coarsening.

Jan 1, 2008

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By A. F. Agnew

Discussion by A.E Agnew Strachan's paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan's use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan's important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

By M. Gunter, M. Buzon, B. McNamee

"A Google search on talc asbestos will yield over 500,000 hits – the reason being the growing number of civil lawsuits in this area. Historically the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos. Ultramafic hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc; they can occur in the surrounding black-wall, also the serpentinite host rock is in direct contact with the talc. Thus allegations can be made non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. INTRODUCTION Gunter (1994) wrote the following in regard to the question “What is asbestos? “The question yields different answers depending upon the audience. To a mineralogist, asbestos is a mineral form. To an engineer, it is an industrial material with several useful properties. To a medical doctor, it is an agent that might cause certain diseases. The third answer invokes several more issues: to a lawyer, a possible lawsuit; to a news reporter, a story; to an asbestos abatement worker, a job; and to a public school administrator or a parent, a nightmare.” The main function of that article was to try and provide background information to be taught at the college level to help students understand some of the issues associated with the use of asbestos in our modern society, and especially its use as a fireproofing agent in schools and public buildings. At that point in time one of the main issues was asbestos abatement as the mining and use of asbestos was waning as its health risks became more clearly known in the occupational setting. Now over 20 years later the current issue we are dealing with herein is “asbestos” occurring naturally in talc. This is a well know concern for those in the talc industry and they have been working on methods to ascertain if their products contained “asbestos” since last century. As such our articles will focus more on issues emerging from recent litigation, and the confusion that occurs, especially in the “asbestos” nomenclature as the mineralogist, engineers, doctors, and lawyers previously mentioned try to communicate. And lastly we need to remain cognizant of the fact that people are still dying of mesothelioma in the US. As a last resort to recoup expenses as they are dying they often respond to the TV advertisements we’ve all no doubt seen."

Jan 1, 2016