Search Documents

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By S. McTavish

Since mechanically suitable grinding mills were available in 1908, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. First and foremost they had to last long enough in an operating mill to protect the mill structure from the abrasive wear of the ore and the grinding media. In addition they had to be able to efficiently transfer the energy from the mill to the mill charge in order to facilitate the grinding process. The liners also had to be easily attached to the mill when new and removed from the mill when worn out. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. 1

Jan 1, 1989

By S. B. Patton

A comprehensive approach to the development and organization of an expert system that is designed to assist electricians in diagnosing electrical faults m mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures m the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchical structure an: formulated by creating "what-if" scenarios and performing a qualitative circuit analysis for each fault Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide' reference material and tutorials on the circuit are also described.

Jan 1, 1989

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By W. G. Kegel

The past few years have produced a rash of demands for changes in America's way of doing things. From manufacturer to consumer, the rules have been changed. Some of the demands were needed and, when legislated to requirements, did manage some good for all concerned. Other demands made by zealots and taken up by regulatory agencies have forced costly changes on our way of life. No segment of industry has been exposed to more new rules and regulations than the deep coal mining industry in the United States. There is no denying that some good has evolved, but most mining men know that the effects have done more to reduce production and increase cost than they were ever intended to do.

Jan 1, 1975

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Cyril W. Draffin

Introduction Americans have long been proud of their ability to recognize a need, define it, and then develop workable solutions. The U.S. underground coal conversion (UCC) program is a good example. In 1974, the need to utilize coal resources that could not be mined was recognized, and Congress gave the Bureau of Mines $1.7 million to gain a better understanding of the UCC technology and its potential applications. Since 1977 when the U.S. Dept. of Energy (DOE) was formed, workable technologies have been tested, the market for underground coal conversion has been recognized, and extensive industrial interest has developed. Perspective The U.S. is blessed with extensive coal resources. Coal supplies about 19% of our national energy needs, yet recently promulgated environmental standards and increasing mining costs have limited direct coal use. UCC potentially can use coal that is economically or technically infeasible to mine because the coal is too thick, deep, dirty, high-ash, and wet; has an excessive angle of dip; or has unpredictable and poor overburden characteristics that make mining unsafe. Coal can be gasified underground or perhaps liquefied below the earth’s surface. Underground coal gasification (UCG) is the prime element of the underground coal conversion program. It enables coal to be converted to gas underground. UCC Coal Resource Recent data show a total U.S. coal resource base of about 6.4 trillion tons. Of this, 1.8 trillion tons might be accessed by UCC, including some minable coal. A commercial UCC process could quadruple roughly the 450 billion tons of U.S. coal reserves, which presently are recoverable by mining. The U.S. coal resources are divided into five sectors. The two most eastern sectors contain relatively thin, swelling bituminous coals that are difficult to gasify. Of the two, the bituminous coal in the Eastern Province is the most difficult because it is deeper than , in the Interior Province and the terrain is more rugged. The sector along the Rocky Mountains contains huge amounts of thick low-rank coals that are the most promising for early development by UCC. The coal has good continuity and the terrain is suitable. Low-rank coals such as subbituminous and lignite are highly reactive and tend to shrink and disaggregate when heated. Most of the coal in the Pacific

Jan 1, 1980

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By M. E. Grimes

The Port Radium mine of Eldorado Mining and Refining Limited, located on Great Bear Lake only a few miles from the Arctic Circle in north-western Canada, is the oldest uranium producer in Canada, The first concentrates were produced in 1933 and except for a period between 1940 and 1942 the mill has operated continuously. Although it is located in a remote area, and compared to more recent mines in other areas is a small tonnage operation, nonetheless the relatively high grade of the Port Radium ore has permitted operation to date on an economical basis. The mill process at Port Radium includes the original gravity concentration mill, and since 1952 an acid leaching plant which treats tailings from the gravity mill and tailings recovered by dredging of residues from underwater dumps in Great Bear Lake. The pregnant solution from the leach plant has to date been processed through aluminum reduction to yield an intermediate grade uranous phosphate-arsenate precipitate, Because of the rising costs of the aluminum reduction process, and its sensitivity to ore composition, Eldorado became interested in possible application to Port Radium of the solvent extraction processes of which we were obtaining increasing information in the latter part of 1954 and during 1955.

Jan 1, 1958

By Cyril W. Draffin

Introduction Americans have long been proud of their ability to recognize a need, define it, and then develop workable solutions. The U.S. underground coal conversion (UCC) program is a good example. In 1974, the need to utilize coal resources that could not be mined was recognized, and Congress gave the Bureau of Mines $1.7 million to gain a better understanding of the UCC technology and its potential applications. Since 1977 when the U.S. Dept. of Energy (DOE) was formed, workable technologies have been tested, the market for underground coal conversion has been recognized, and extensive industrial interest has developed. Perspective The U.S. is blessed with extensive coal resources. Coal supplies about 19% of our national energy needs, yet recently promulgated environmental standards and increasing mining costs have limited direct coal use. UCC potentially can use coal that is economically or technically infeasible to mine because the coal is too thick, deep, dirty, high-ash, and wet; has an excessive angle of dip; or has unpredictable and poor over-burden characteristics that make mining unsafe. Coal can be gasified underground or perhaps liquefied below the earth's surface. Underground coal gasification (UCG) is the prime element of the underground coal conversion program. It enables coal to be converted to gas underground. UCC Coal Resource Recent data show a total U.S. coal resource base of about 6.4 trillion tons. Of this, 1.8 trillion tons might be accessed by UCC, including some minable coal. A commercial UCC process could quadruple roughly the 450 billion tons of U.S. coal reserves, which presently are recoverable by mining. The U.S. coal resources are divided into five sectors. The two most eastern sectors contain relatively thin, swelling bituminous coals that are difficult to gasify. Of the two, the bituminous coal in the Eastern Province is the most difficult because it is deeper than in the Interior Province and the terrain is more rugged. The sector along the Rocky Mountains contains huge amounts of thick low-rank coals that are the most promising for early development by UCC. The coal has good continuity and the terrain is suitable. Low-rank coals such as subbituminous and lignite are highly reactive and tend to shrink and disaggregate when heated. Most of the coal in the Pacific

Jan 9, 1980

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By Anthony Edey

It is a generally accepted and widely discussed fact that the world in general, and the United States in particular, face a shortage of energy at the present time which will become worse in the future. There is, however, no sign of a similar concensus as to the actions which would prevent or overcome this expected shortage. An immense variety of solutions has, however, been put forward, ranging from the purely political to the outer fringes of sophisticated technology. One resource which surprisingly is often only cursorily included in this discussion is the immense known petroleum reserve lying within the United States. When this subject is discussed, indeed, it is usually in the context of the improvements in production or new discovery rate that could be expected to result from possible politico-economic actions that would raise the real price obtained for domestic crude. This interest in the potential for improved domestic production is undoubtedly justified, but very little attention is normally drawn to the fact that even under the most favorable policy framework the majority of the oil that has been, or will be, discovered will remain in the ground due to the inherent limitations of production through surface wells.

Jan 1, 1979

By James A. Pendleton

In response to Public Law 95-87 (SMCRA), Colorado promulgated regulations governing the mining of Coal. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence. All permitted underground coal mines within Colorado have approved subsidence programs. Preliminary monitoring results indicate the subsidence mechanical predictions have been sufficiently accurate to preclude material subsidence damage. The State of Colorado has developed a practical approach to regulating subsidence, which stresses monitoring verification of predicted subsidence phenomena. However, shortcomings exist in our ability to precisely predict the secondary consequences of subsidence, including effects to structures, the hydrologic balance and the environment. Lack of accuracy in predicting these secondary consequences results in uncertainty, necessitating conservatism in permitting. To avoid increasingly stringent permit restrictions, future research should emphasize the secondary consequences of subsidence.

Jan 1, 1986

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By Edward R. Borcherdt

When one considers the advancements made during the 25 years prior to the late fifties, and compares these advances with the progress made in the past decade, the comparison is indeed startling. It was not until 1935 that trucks began to replace rail as a major hauling facility, Initially, the haulage capacity of end dump trucks was limited to 18 or 20 tons. "Straight stick" transmissions were utilized and the available horsepower was minimal. In the early forties single planetary axle 25 ton trucks were introduced, and shortly thereafter those were followed by 35 ton tandem axle units.

Jan 1, 1967

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999