Search Documents

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By S. Bentley

"Everyone has a general idea what mixing means, but describing the mixing process is not so simple. The objective of any mixing process is to distribute and blend the materials with different characteristics, different quantities as evenly as possible resulting in a homogenous mixture. Introducing proportional movement with the optimal intensity into the materials achieves effective homogeneous mixing results. A simple one directional movement with inadequate acceleration of the materials would obviously not achieve the same mixing results. This would be more like stirring than mixing. The amount of relative movement that is introduced is a decisive factor. Circumstances for successful mixing involve distribution of all materials, and achieving the highest probability that all recipe particles located in a specific position at the beginning can be found at any random location in the mixing chamber at the end of the process. This is the only way to ensure that a consistent result is achieved every time mixing is repeated.THREE-PART CYCLE The mixing cycle occurs in three phases; charging the mixer, the mixing process, and discharging. The sequence in which the individual materials to be mixed are filled into the mixer can have a huge impact on the efficiency of the mixing cycle. The mixing cycle overlaps the charging process and the discharge cycle follows the mixing cycle. To achieve optimum results, effective discharging methods should be taken into consideration to avoid risks of segregation. Costs for energy and wear should be as low as possible and finally, it is very important that the mixing cycle takes place as quickly as possible. In concrete or paste backfill production, selecting the best mixing technology is crucial for both the quality of the final product to be blended and the efficiency of the production process. The optimum mixing system is one that rapidly disperses all ingredients evenly throughout the mixing trough and completely surrounds all the course or fine aggregate particles with the slurry cement particles. Specific for paste production it’s the mixers job to also break-down unconditioned tailings to achieve consistent paste viscosity or measured spread. Many paste and concrete formulas also involve small quantities of chemical additives which also must be evenly distributed effectively. The time required per mixing cycle as well as the costs of energy, wear and maintenance will determine the economy of the concrete production."

Jan 1, 2015

By R. C. Woodhead

During past years the most difficult problem presented to the coal preparation engineer has been the cleaning of fine coal, The problem of handling fine coals is more involved than the coarser sizes, because the higher surface moisture contents complicate screening, and the larger percentages of fine near size material complicate separating problems. Low gravity high capacity specific gravity separations were not possible with equipment available at that time. Coal preparation engineers did develop machines that would effect a separation of the fines, however, to maintain a high efficiency, the point of separation had to be a relatively easy one. The more difficult separations were made in the coarse coal sections of the washeries, and the fines were generally cleaned at higher specific gravities in equipment such as tables, feldspar jigs, rheolaveurs, etc. Clean products from both processes were mixed, resulting in overall lower ash contents, During the last several years, however, we have been confronted with increasing demands ZGP more precise separations of finer coals to still further reduce ash contents. A study was begun and a program instigated to improve the cleaning of fine coal, The result of this endeavor was the development of the new cycloidal heavy medium cyclone.

Jan 1, 1964

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Keith A. Yarborough

INTRODUCTION The National Park Service (NPS) conducted a research program from mid-1975 to early 1978 to measure alpha radiation levels in natural caves which it administers. Subsequently, a long-term management program was developed which has conducted routine monitoring of radiation levels and has computed employee exposure accumulations in certain NPS caves. The overall program: research and management; was undertaken to evaluate the possible health hazard to cave visitors, interpreters, researchers, maintenance personnel, concessions employees and other workers and to protect their health. The results of this work have been reported extensively elsewhere (see References 1 through 3, 5, 6, 9 through 13, and 14 through 26). This paper deals with the relation of radon gas and daughter produced radiation levels to the cave air flows which mobilize them. These flows are a function of interior cave and exterior ambient air temperatures and pressures and of the cave's geophysical configuration. The low-level, ionizing radiation is produced by minute concentrations of radon and thoron gases which emanate from within caves. Because of confinement, the radiation levels are often appreciably higher than in surface atmospheres. Subsequent radioactive disintegration of the gases into their ionized "daughter" products, which are particulates, permits distribution of the alpha radiation throughout a cave system. The extent and character of this distribution depends upon the particular cave and the air flows which it produces. Thus, the alpha radiation serves as a "tracer" to describe the flows. The flow analysis is divided into two parts: 1) A qualitative description with respect to the two basic geophysical cave types over both long-term (annual) and short-term (diurnal to weekly) periods. 2) A quantitative description of the unsteady, uniform and non-uniform, one-dimensional, incompressible motions for both influent and effluent air flow situations in both basic geophysical cave types. A part of the qualitative description presents "Special Measurement" data: Tsivoglou [vs.] Kusnetz working levels, Tsivoglou individual daughter levels and free ion concentrations, radon gas concentrations, and equilibrium ratios. A great deal of important work has been carried out by Mr. Bobby C. Carson, Cave Radiation Technician at Mammoth Cave National Park, Kentucky. He reports these findings later in this conference (Ref. 6). Some of his results have been used here to establish the cave air flow analysis. Other National Park Service personnel have made measurements at others of the caves for which data are reported here. All of this work and cooperation has been vital to the success of this research program. It is very much appreciated. THEORETICAL FLOW DESCRIPTION Previously reported research (See Ref's. 20, 21, 23 and 25) has established the qualitative relationship between the alpha radiation in caves and their natural air flows. The radiation serves as a representation of these air flows. Changes in radiation with time represent changes in the main forces which produce the air flows. The quantitative data have substantiated that [all caves in which the primary cause of air flow is due to temperature produced gravity (density) gradients and also having minimal man-made disturbances, experience seasonal variations in airborne alpha radiation. The radiation levels increase in summer but decrease in winter], based upon seasonal air movements through each cave system which occur naturally. Two general types of physical cave configurations which control the air flows have been identified as: 1. Those which go up into a hillside or mountainside: Type I ("Upside-down" = USD). 2. Those which go down into the earth; Type II ("Right-side-up" = RSU). These act to control the air flows seasonally. The summer increase in Type I caves is due to increased air flows, whereas in Type II caves it results from stagnation or reduced air flows. This seeming paradox is explained by the physics of the air flow regime in each cave type and has been detailed elsewhere [Ref's. (20), (22) through (25)]. It[ i] true, in general, that air flow decreases airborne radiation in the [immediate vicinity] in which it occurs. Any paradox results from subsequent distribution throughout the case as to [ how] the air moves through a cave [system] with respect to time and space. Exceptions to the cave air flow "rule" are: 1. Caves in which pressure gradients and pressure fluctuations [predominate] in producing the air flows. 2. Caves in which man-made effects and management practices are superimposed on the natural air flow regime. Man-made disturbances which can alter the natural cave air flows are tunnels, elevator shafts, bore holes, sealed and closed portals, etc. If these are not properly sealed, the natural air flows which they change will totally alter the distribution and seasonal variations of the alpha radiation levels. These exceptions may act separately or in combination.

Jan 1, 1981

By Nicola Della Valle

The Singapore Land Transport Authority (LTA) is currently expanding capacity by extending their Metro system from South of the city to the North East end of the island. The scope of Contract 704 involved excavating a long reach of tunnel which had a complex rock/soil interface comprised of fresh granite overlaid by clayey sand. Two 6.5 m diameter Earth Pressure Balance (EPB) TBM’s were used to bore the tunnels. These machines were designed so that both hard and soft rock could be excavated. The cutter head was equipped with a combination of both rippers and disk cutters. Soil conditioning was achieved by delivering foam through a multiple port injection system. This very irregular profile of the interfaces posed many challenges to the equipment and the people.

Jan 1, 2001

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By John Drew Ridge

Tables showing world trade in metallic mineral raw materials during the years 1953 through 1957 have been prepared for the following twenty-one commodities: alumina, aluminum, bauxite, chromite, copper concentrates, partly refined and fully refined copper metal, iron ore, pig iron, iron and steel (simple shapes), lead concentrates, lead metal, manganese ore, mercury metal, nickel ore, concentrates, and matte, nickel metal, raw pyrites, sintered pyrites, tin concentrates, tin metal, zinc concentrates, and zinc metal. In each instance, the amounts given by the importing country were used except when statistics from the importing nation were lacking, incomplete, or misleading. To show the considerable divergence between importing and exporting country totals for the same years, the complete mercury table is given and, in parallel columns, shows the comparable tonnages of importers and exporters. Tables for the other twenty commodities are presented in summary form. The data of the concentrate tables are used with those of the corresponding metals as a basis for a discussion of trade in concentrates versus trade in metals. The data of all twenty-one tables provide the basis for testing the thirteen rules governing international trade in metal raw materials which I first published in Mining Engineering for July 1955. Because the 1953 through 1957 data are far more complete and considerably more extensive than those on which the 1955 rules were based, it was found possible to deduce five additional rules and to modify three of the original thirteen appreciably. The full text of the eighteen rules is given.

Jan 1, 1960

By Russell H. W. Chadwick

Reviewing events in the minerals industry, in economic geology, and in my own exploration work, I find that the most compelling subject for comment is the increasing ferment in ore deposits theory. New discoveries and continued investigations of bedded deposits of lead and zinc, copper, iron, uranium, etc., coupled with the availability of much new and significant data from sedimentary and metamorphic petrology, geochemistry, and oceanography, has led many economic geologists like myself to become disenchanted with former simplistic notions. Now disenchantment among serious people should presuppose both valid objections to the old, and valid new substitutes. I can sum up my own position and, I believe, what most of the recent writers on ore deposits theory are trying to tell us, by saying that a physico-chemical (bench science) approach to a natural science is neither correct nor useful, and that the obvious cure is a return to the study of the geology of ore deposits. More specifically, ore should be viewed merely as an unusual concentration produced, in stages, by the natural processes inherent in the geochemical cycle. In criticizing the conceptual basis of a science, one is involved simultaneously in the inherent character of the science, its subject matter, and the old and new concepts. I have found it impossible to make a clean separation along those lines. As a result, and as the title suggests, these are not-quite-random reflections on genesis, a matter near and dear to all true treasure hunters since Agricola.

Jan 1, 1967

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By George S. Austin

Perlite is rhyolitic glass with 2 to 5 percent by weight (wt.%) bound water held within the silicic-glass structure. It is often distinguished by vitreous, pearly luster and concentric perlitic fractures ("onionskin"). Occurrences worldwide are associated with Tertiary to middle Quaternary volcanic rocks. Perlite is in silicic domes, plugs, laccoliths, flows, vitric tephra, chill margins of dikes and sills, and welded ash-flow tuffs. It is a hydrated volcanic glass formed through secondary alteration of obsidian by the incorporation of water into the glass/silica structure. Post-emplacement hydration (weathering) of cooled glasses by meteoric water is the principal alteration process, but some hydration by magmatic or meteoric water during or shortly after emplacement, or hydration by water exsolved during cooling may occur. Commercial "perlite" is any volcanic glass that expands or "pops" when heated quickly to plasticity while evolving steam and thus forming a lightweight, frothy material. The expansion temperature typically ranges from 1,100 to 1,500°F. An expanded volume increase of 10 to 40 times the original volume yields expanded densities of 1.5 to 11 pounds per cubic foot (lbs/ft3). Perlite is mined by eight companies at 10 operations in six western states. New Mexico accounts for more than 80% of the total tonnage mined. The rest comes from Arizona, California, Colorado, Idaho, and Nevada. In 1992, domestic production was 571,000 short tons (st), domestic apparent consumption was 591,000 st, and the value of crude perlite was $15.3 million. In 1991, with about the same production and price of crude perlite, the gross value for expanded perlite was $101.7 million. Perlite exports in 1992, primarily to Canada, are estimated an 30,000 st; and imports, from Greece, are an estimated 50,000 st. In 1992, 70 plants in 33 states expanded crude perlite. Construction uses of expanded perlite accounted for 66% of total domestic sales. Expanded perlite used as filter aid accounted for 15%. All other markets, including use as a filler and in agriculture, accounted for 19%. Leading states for expanding perlite, ranked by order of sales, were Mississippi, Pennsylvania, California, Illinois, and Georgia. Domestic perlite encounters transportation disadvantages in some areas of the eastern United States compared to perlite imported from Greece. However, western U.S. perlite exports to Canada offset this in large part, and net import reliance for perlite is about 3% of domestic consumption. Perlite grab samples were tested at the New Mexico Bureau of Mines and Minerals Resources (NMBMMR) for their basic suitability in horticulture, construction, filter aids, and fillers/extenders using Perlite Institute techniques modified by the NMBMMR. Most commercial perlite ranged from 2.5 to 3.0 wt.% bound water for all major types (classical, granular, and pumiceous). Expanded density varied widely, but the lowest density of 1.9 lbs/ft3 was for granular. Average brightness of expanded perlite was 47.6 to 69.3%. Nonexpansibles, commonly obsidian or "dead" perlite, ranged from 18 wt.% to less than 1 wt.%, with granular perlte generally the lowest. Compacted density was not related to either perlite type or nonexpansibles present. Sieve analyses of the -50+100 mesh product showed that, in general, pumiceous perlite produces more fines and classical and granular perlite average 60 to 80% -30+100 mesh after expansion. Samples were tested for crystalline silica that ranged from below the detection limit of 0.5 wt.% to nearly 0.2 wt.%, but most tested below 0.5 wt.%. Although quartz content can be lowered in the expanded product by the expansion process, producers can further lower crystalline silica in the product by mixing low-quartz crude with high-quartz perlite before expansion. Chemical analysis by x-ray fluorescence confirms the rhyolitic composition of perlite, but indicates that surface weathering may increase the concentration of some elements, such as potassium and calcium, by infilling cracks or fissures developed during or after perlite emplacement.

Jan 1, 1995

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005