Search Documents

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By R. M. Williams

Introduction Ring roller mills are efficient size reduction machines embodying the following machine functions: 1) Size Reduction: from a feed size of 2 in. to various size products as fine as 400 mesh, or granulation from 2 in. to 6 mesh containing a minimum of fines. 2) Drying: fluid bed drying of wet feed materials. 3) Conveying: negative pressure air system results in dust-free conveying. 4) Beneficiation: liberation and removal of foreign materials from the auxiliary bottom discharge simultaneously while grinding. Operation Operation of the roller mill system, Figs. 78 and 79, is completely automatic. A feeder introduces raw material into the grinding chamber in the base of the roller mill at a rate determined by pressure variations within the roller mill as material is ground and air conveyed away. The feeder will be activated by the reduced static pressure and introduce unground material into the system, thereby maintaining a constant differential pressure. Plows located ahead of each grinding roll direct the material upward and between the grinding rolls and the bull ring where it is ground to size. The grinding rolls are free to swing out centrifugally, which forces them to bear upon and grind the raw material. Being free to pivot axially, the rolls automatically assume the proper position for grinding and need no adjustment to compensate for wear. Rotation of the rolls is by rolling contact. Once ground to size, material is swept out of the mill by the controlled air flow from the centrifugal main mill fan. Air suspended, the ground material passing through the adjustable spinner separator. In the separator, an accurate size classification is made which allows product-size material to be conveyed away from the roller mill while oversize material is returned internally for additional grinding. By varying the speed of the separator drive, more or less cyclonic action is achieved at this location, effectively controlling product size. Product sized material is removed from the airstream by the cyclone collector. Typically, a conveyor or product storage bin will be located to accept the product as it exits from the bottom of the cyclone collector.

Jan 1, 1985

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013

By Ravi Sahu

"In the global mining industry, there are those who seem resigned to the fact that the mining industry has always operated according to certain time-tested principles that don’t involve jumping on every new technological trend. Others expect that mines will soon have autonomous electric vehicles running around the clock. The truth lies somewhere in the middle. In business, as in life, that is usually the best path to follow.The instant access to people and information provided by 21st-century technology continues to push businesses in all industries toward greater efficiency and unheard-of levels of modernization. And in the world of mining, the embrace of advanced technology is all about managing risk.However, even in this age of digital information overload, some mine sites still require employees to physically download data from individual trucks to monitor payload data and inspect road conditions using a clipboard. What’s more baffling is that other mine sites still have no way of tracking tons moved at all.This isn’t due to a lack of innovation in the industry. Quite to the contrary, there is an abundance of new technology available that provides real-time monitoring of vehicle movements and tracks road conditions without the intervention of people. So why are owners reluctant to embrace advances in mining tech?Gauging the value of changeSurvey data has traditionally been captured by ground laser scans and LIDAR systems. A mine site surveyor would drive around the pit with a truck-mounted scanner to generate a point cloud. This process would be completed every few days and would take an entire day.The many cons of this method far outweigh the pros. First, it provides no visual data. If an operation has moved beyond the roller wheel and tape measure, visual pit models and LIDAR scans are typically completed once every six to 12 months by an aerial flyover, but such sporadic information gathering isn’t likely to result in the most actionable data. Moreover, given the high cost (in terms of both money and time), the numerous safety and liability issues, and the lack of flexibility in scheduling, manual processes are more trouble than they are worth.Overall, while miners are excellent operators who value innovation, their employers often try to outsource it or acquire innovators instead of investing in existing technology that can improve current operations. It is a never-ending dilemma:"

Jan 5, 2018

By J. H. Canterford

To date, large-scale solution mining has received little attention in Australia, although the potential of this technique has not gone unnoticed. The possibility of long-term damage to the local environment has also been recognized. Because no two orebodies are the same, it is clear that the application of solution mining techniques and the assessment of environ- mental damage will be somewhat different for different orebodies, even though the general principles will be the same. At present the most significant copper solution mining operation in Australia is at the Mammoth (Gun- powder) Mine in northern Queensland. This mine currently produces more than 3 000 t of cement copper a year.1

Jan 1, 1981

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007

By C. H. Bucknam, S. A. Wilson, G. E. McClelland

The Meteoric Water Mobility Procedure (MWMP) was developed in the State of Nevada during the 1980’s as part of their mine waste characterization programs. During the 1990’s the Waste Subcommittee of the Nevada Mining Association (NvMA) contacted ASTM Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials to undertake a standardization program for the method. A cooperative program was developed in conjunction with the Acid Drainage Technology Metal Mining Sector (ADTI-MMS)Prediction Committee, which involved eight of the NvMA labs performing duplicate leaching tests on two test materials: a coarse fraction of the USGS Hard Rock Mine Waste standard and a typical spoils sample from a heap leach operation undergoing closure in Nevada. Solutions for metals analysis were preserved and sent to the USGS Laboratories in Denver to determine the reproducibility and repeatability of the leaching. The history of the method and reference material and the results of the interlaboratory testing and statistical analyses will be presented.

Jan 1, 2003

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By Adrian Smith, Debra W. Struhsacker

There is now overwhelming evidence that, despite concerns to the contrary, natural degradation of cyanide and cyanide attenuation by hydrogeochemical processes are capable of minimizing or eliminating potential water qua1ity impacts from heap leach systems. A1 though there was some recognition of these data by the regulatory authorities, for example the initial USEPA modification of cyanide standards to an advisory level, many states have codified standards inappropriate to the clearly site specific nature of heap leach operations. As an overview to this problem, this paper will integrate the theoretical chemical data on cyanide with the observed geochemical behavior of cyanide in the decommissioned heap leach environment. The cyanide species that are likely to exist within an abandoned heap leach system will be identified, and the relative toxicity and potential environment effect of these cyanide species will be discussed. These data will then be used to evaluate cyanide detoxification regulations for decommissioned heap leach projects in 14 states.

Jan 1, 1987