Search Documents

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By Franklin H. Sharp

During the last few years the New Lead Belt of South- eastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper, and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, Missouri for about thirty-five miles. The area is part of the Ozark uplift and consists of steep-sided, heavily wooded hills with narrow valleys. Surface streams are very erratic, normally having low flows but becoming rushing torrents during the violent thunderstorms that occasionally occur. Because of the pristine nature of the country and the newness of the mining developments, the environmental impact of all phases has been closely watched.

Jan 1, 1973

By John B. Draper

The 1980 Mine Dewatering Act was enacted to protect water rights and to allow mine dewatering to proceed where impairment of a water right might have otherwise created a bar to mine development. In New Mexico, new appropriations for beneficial use are subject to the State Engineer's jurisdiction and are granted only upon a showing of non-impairment. Before 1980, mine dewatering was not considered a beneficial use, nor was it considered waste. The Act brings mine dewatering under the jurisdiction of the State Engineer, makes it subject to the same requirements as an application for appropriation for beneficial use, grants the right to replace the water of users whose rights would be impaired by mine dewatering without a plan of replacement, and extends the right of replacement to non-mining appropriations of water for beneficial use, Application of the Act requires determination of the definition of impairment (the threshold of significant impact on existing water rights), hydrologic evaluations to determine the impact of the proposed dewatering, and preparation and execution of a plan of replacement to avoid impairment of existing rights.

Jan 1, 1983

By Stanley C. Suboleski

1977 was the modern day low point for productivity in the coal industry. At that time, no one could have predicted that the industry was about to enter a productivity rise that would continue unabated through the 1980s. Thirteen years later, the cause of this phenomenon is still not well understood. While many government studies focused on the fall in productivity from 1969 to 1977, none have been undertaken to explain the rise. Some of the likely causes of the gain in productivity during this period will be discussed here. An attempt will also be made to quantify the value of some of the technical innovations that have taken place. The remainder of the gain is assumed to come from non-technical sources. The nature of these sources, although largely non-quantifiable, is also discussed. Since the number of mines that have adopted the technical innovations noted here is largely unknown, the actual contribu¬tion of technological changes to the overall productivity gain can only be estimated.

Jan 1, 1990

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Norman Miskelly

Role of CRIRSCO CRIRSCO has an advisory and hopefully influential role in International Mineral Resource/Reserve Reporting Standards CRIRSCO also has a broad educational role CRIRSCO does NOT have a negotiating role CRIRSCO does NOT have a regulatory role

Jan 1, 2003

By J. W. Francis

The paper about to be presented deals with the relatively straightforward problem of mining two seams of coal separated by an interval. This may seem to be a simple problem but within a twenty-mile radius of Consolidation Coal Company's Burning Star # 4 Mine at least seven (7) different techniques of two-seam mining have either been tried or are now in use. This great variety of techniques should point out that there is no single simple solution; a conclusion often reached when dealing with mining problems. As a background for the techniques presently in use at the Burning Star # 4 Mine, we will briefly outline the other five (5) stripping techniques used in the area: 1. Captain Hine 6360 Range Diagram (Figure 1) 2. Leahy Mine Range Diagram (Figure 2) 3. Burning Star # 3 Mine 5860 Range Diagram (Figure 3) 4. Burning Star # 3 and # 4 Mines Dragline in Pit Range Diagram (Figure 4) 5. Captain Hine 2570/5561 Range Diagram (Figure 5) Each of these techniques was chosen because it provided the best and least expensive alternative for mining the coal under the particular restraints encountered. The Mine Engineers at our Burning Star # 4 Mine, Mr. Dennis Mahan and Mr. William Weaver, will now detail two additional mining techniques, out-lining our experience to date.

Jan 1, 1977

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By Donald J. Worth

When Eugene Bailey asked me to contribute to this session on "Canadian exploration - 1976", it took a little coaxing before he got me to agree. My immediate reaction was, what could i say about Canadian exploration that already had not been said a hundred times in the past few years; secondly, why include a banking person in such a discussion? Everyone knows banks only come into the picture after the discovery has been made and feasibility well established and validated. Rather than wrestle with these misgivings, I decided to take the easy way out and go on blind faith in Eugene - that is, he asked me so he must think that I could come up with some useful thoughts and at least touch upon some of the pros and cons of exploration in Canada. The object of the whole exploration exercise is to Find economic deposits, once they are found, one cannot really move them elsewhere to mine them. It follows, therefore, that we should really be speaking about the pros and cons of mining In Canada and my treatise will eventually lean in this direction. In any event and before getting down to the pros and cons, let us take a quick look at the history of mineral resource development in our country since the end of world war II. At that time, we were producing well under one billion dollars worth of mineral products including hydrocarbons.

Jan 1, 1976

By Denys B. Smith

Electric logs and cuttings records from Zechstein 3 and 4 strata in boreholes in the British Sector of have been interpreted in the light of numerous cored boreholes through this sequence in north-east England. This interpretation shows that potash salts in the two cycles are thickest and most consistent in a belt 20 to 40 km wide parallel with and a few kilometres from the present basin margin, and are here generally similar in grade to those known onshore. The potash ores in both cycles are mainly of sylvinite in onshore areas, the layered Upper the Southern North Sea Potash of the fourth cycle being rather less variable but generally of appreciably lower average grade than the Boulby Potash of the third cycle. Potash salts in both cycles are highly variable in thickness and grade in basin centre areas where they have been grossly affected by diapirism of the thick second cycle salts.

Jan 1, 1978

By G. Yang, M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya

In the last 20 years, studies on controlled flow recirculation in various countries have been carried out in both coal and metal mines. These studies have shown that in addition to economic gains, partial flow recirculation can be used to provide mine workings distant from surface access points with the required volumes of air. These studies have also shown that the operation of fans and regulators, used in a recirculation system, will induce transients in gas flow and gas concentration. Various models have been developed to explain the problem. However, most have failed to incorporate important factors such as diffusion and dispersion in the modeling process. This study examines the theoretical background of gas emission transients from caved areas in coal mines, represents the problem by a "tank-airway" network model, and provides a possible solution. The study also presents the results gained from a laboratory model constructed to evaluate the major factors affecting the shape and duration of gas flow and gas concentration transients in an airflow recirculation system. In this model, the gas injection system was rearranged to simulate the variations in gas emission rates due to changes in air pressure. Within this model, a set of booster fans and regulators were used to generate the changes in air pressure within the model. Finally, the study presents an algorithm and a computer program GASTRAN, developed to analyze the gas concentration transients and calculate the pollutant transport levels in a complex ventilation network. The application of the program is illustrated by means of an example problem.

Jan 1, 1991

The Awareness and Preparedness for Emergencies at the Local Level (APELL) program is a process that helps people prevent, prepare for and respond appropriately to accidents and emergencies. APELL was developed by the United Nations Environment Program, in cooperation with industry groups, governments and local communities. Since its beginnings in1988, the program has been implemented in more than30 countries. APELL is a tool for bringing people together to allow effective communication about risks and emergency response. The program provides a common-sense approach to accident prevention and response.

Jan 1, 2003

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007