Search Documents

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By Louis W. Cope

Many Americans have seen Greenland while flying over it on their way to or from Europe. Few have visited this largest island in the world. Portions of the 20 percent of the territory that are not ice-covered are highly mineralized. Greenland could become very productive if the present interest in exploration increases. The people and Greenland’s history The population of Greenland is 57,000. Twenty percent are Europeans, mainly of Danish decent, while 80percent are native Greenlandic or mixed Greenlandic-European. The native population is the same as the Inuit of the Canadian Arctic. They speak the same language.

Jan 1, 2004

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By Charles F. Herbert

The waves of prospectors who struggled across the wide Alaskan wilderness between 1898 and 19 10 came close to but did not actually find the rich copper/zinc/silver deposits strung out along 161 km ( 100 miles) of felsic schist in the remote Brooks Range of northwestern Alaska. They had heard rumors of gold in the valley of the Kobuk River, so they skirted the Arctic ice pack in the Chukchi Sea and, in a force at least 800 men strong, ascended the Kobuk River in 1898. Twenty-eight placer mining camps were established but only a handful survived for more than a few years. One of the placers that died rapidly was Ruby Creek. A map showing the location of Alaskan mineral deposits is given in Fig. 1. The Ruby Creek miners, disappointed with the scarcity of gold in that creek, followed copper-bearing float to two places where the float was especially plentiful. Pits, a short adit, and a shallow shaft uncovered copper carbonates, bornite, and chalcopyrite in fractured limestone but the remoteness of the district blocked efforts to sell the claims or to raise capital for development. Shortly after 1906, the copper prospects were abandoned and, except for an account published in 1913 by the US Geological Survey, they were forgotten, as were the names of the prospectors.

Jan 1, 1991

By S. R. LaBrooy, M. C. Costello, A. C. Bax

Nickel is present in a number of gold ores in Australia, Africa and the United States. The effects and behaviour of the nickel during the cyanidation and adsorption processes, and also during the elution and electrowinning processes have been examined by a number of researchers, usually as a part of a larger investigation. This paper examines the available data on the behaviour and effect of nickel during cyanidation and its associated unit processes. The presence of nickel is often not considered to be particu­larly important as it does not cause the same degree of problems across the circuit as those experienced in the presence of copper. It can however lead to increased cyanide consumption during leaching, and reduced adsorption of gold onto carbon. A proportion of nickel cyanide may be removed from carbon prior to elution by carrying out a hot (90° C) acid wash. The nickel which remains on the carbon will be partially eluted during the main elution step, and, dependent on its concentration in the pregnant solution, part of it may be deposited during electrowinning. There is always a risk that any nickel remaining on the carbon after the elution step will be reduced to metallic nickel during the regeneration step. This may ultimately result in an increasing base level of nickel on the carbon, as metallic nickel is insoluble in both cyanide and hydrochloric acid.

Jan 1, 1995

By John B. Spencer

Earlier this year, Simplot Phosphates achieved a safety milestone at its Vernal, UT phosphate operations. In March, the entire operation reached achieved seven years without a lost time accident. And the mine operations at Vernal reached the 1 million hours benchmark without a lost time accident. This million hour achievement has been 19 years in the making. This achievement reflects the mine’s strong attitude towards safety, the company said. Safety is an integral part of its culture and requires diligence and considerable work. Attention to even the smallest of details cannot be allowed to slip. This is a record Simplot Phosphates said it hopes to improve on every day.

Jan 1, 2004

By Bruce Gellar

In March, the Prospectors and Developers Association of Canada (PDAC) held its annual conference in Toronto, Ontario. This is the third PDAC meeting the author has attended. The following are some impressions of the meeting. And the author looks forward to the joint meeting of the PDAC and the Canadian Institute of Mining, Metallurgy and Petroleum to be held March 5-10, 2000, entitled Mining Millennium 2000. One of the features of next year’s gathering is a proposed forum of world mining ministers, the first ever to be held anywhere.

Jan 1, 1999

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By K. A. Brunk

This paper describes Newmont's research, operations, history and experience with pre-treatment of preg robbing carbonaceous ores. The chemistry, physics and kinetics of chlorine treatment are described. Present operations, control strategy and projected changes are discussed. Included is a summary of the adsorption of chlorine into pulps and off-gas scrubbing.

Jan 1, 1987

By Faruk Oksuz

The owners of large infrastructure projects are challenged on how to implement sound engineering and construction contracting strategies that address their prime expectations: a quality job, on time and within budget. With the increasing number of large engineering and construction projects worldwide, owners continue to search for alternative contracting strategies to address their risk, quality, sustainability (operability and performance), schedule, and budget concerns. Coupled with the shortage of resources, delays, political pressures, and other obstacles in procurement and negotiation processes, engineers and contractors are also looking for creative ways to optimize contract packaging strategies for efficient and successful project delivery. This paper compiles an array of decision making criteria and suggests a balanced evaluation, ranking and selection strategy in procurement of both engineering and construction services for large tunneling and other infrastructure projects. A number of owners? general preferences and viewpoints are discussed on large tunnel programs encompassing water and wastewater conveyance systems, pump stations and treatment facility upgrades. Contract packaging strategies and project phasing and segmenting alternatives for preliminary engineering, final design, construction management, and actual construction of facilities are featured for several large water and wastewater infrastructure projects. While the selection (and the relevant selection process and criteria) and performance of service providers, whether for engineering or construction, have profound effects on the outcome of any given project, this paper only examines strategies for con-tract packaging. More specifically, the authors evaluated case studies and developed a range of recommendations for packaging of large water and wastewater infrastructure projects with multiple components.

Jan 1, 2008

By K. P. Black, G. W. Sevick, D. E. Hockley, K. S. Sexsmith, J. T. Chapman

Mineralogical analyses of carbonates in depyritized tailings and pyrite concentrate (from depyritization of the tailings) were completed as part of the tailings characterization for the Crandon Project, a massive sulfide deposit in northeastern Wisconsin. The mineralogical study was designed to determine the proportion of calcium and magnesium carbonates, and therefore the effective buffering capacity of carbonates in the tailings. The depyritized tailings are net acid consuming and will be stored in a surface tailings management area. The pyrite concentrate is net acid generating and will be used as backfill in the underground mine workings. The majority of carbonates in the depyritized tailings were ferroan dolomite containing 10 to 15% iron (by weight) and lesser amounts of siderite and magnesian siderite. The proportion of calcium and magnesium-rich carbonates corresponds to several independent tests of carbonate neutralization potential (CO3-NP) availability. The pyrite concentrate had less CO3-NP, indicating segregation of the carbonates during pyrite flotation. These carbonates reported higher iron contents, consistent with the relatively lower availability of CO3-NP in the pyrite concentrate.

Jan 1, 2002

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

By Van E. Housman, Stephan Hoffman

Introduction Based upon the 1980 Bevill Amendment to the Resource Conservation and Recovery Act (RCRA), a 1986 Regulatory Determination decision, and subsequent rulemakings, the Environmental Protection Agency (EPA) exempted all extraction and beneficiation wastes and twenty mineral processing wastes from regulation under RCRA Subtitle C (hazardous waste) regulations. These twenty mineral processing waste streams were studied in a 1990 Mineral Processing Report to Congress. For purposes of regulatory classification, EPA made special distinctions between extraction/beneficiation and mineral processing. Wastes determined by EPA to be from the extraction/beneficiation of ores and minerals retain the exemption, while wastes found to be mineral processing, except for the “special" twenty mineral processing wastes, fall within RCRA Subtitle C jurisdiction. For those wastes that are subject to RCRA Subtitle C, § 3004(m) of RCRA requires EPA to set levels or methods of treatment, of any, which would substantially diminish the toxicity of the waste or substantially reduce the likelihood of migration of hazardous constituents from the waste so that short- term and long-term threats to human health and the environment are minimized. These treatment standards are developed by EPA under the Land Disposal Restrictions (LDR) program. Under § 3004(g) (4) of RCRA, EPA is required to promulgate treatment standards for any waste that is newly identified or listed as hazardous. As part of the settlement agreement in Environmental Defense Fund (EDF) v. Reilly and Chemical Waste Management, Inc. v. EPA (1992), EPA has agreed to propose a rule by June 30, 1995 and promulgate a final rule by June 30, 1996. This rule is commonly referred to as the "Phase IV" LDR rule and will address newly identified mineral processing wastes. Other wastes that will be addressed in this rule include newly listed dyes and pigments and wood preserving wastes. Therefore, in the Phase IV rule EPA will develop treatment standards for all mineral processing wastes that have lost their Bevill exclusion. EPA is currently collecting information on the waste characterization, treatment alternatives, and disposal capacity data currently available on these wastes. EPA is also soliciting data and information on opportunities for

Jan 1, 1995

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012