Search Documents

The Coal Utilization review arrived too late to appear in the May issue. Coal utilization technology is improving due to the urgency with the 1990 Clean Air Act and the incentives provided by the Clean Coal Technology (CCT) program. Advances in the CCT are the subject of this report because of their broad industry application, support and involvement. Clean coal demonstration program Projects in the $5 billion Clean Coal Technology program are jointly funded cooperative agreements - not contracts - between government and industry. The industry participant in each project contributes at least 50% of the total cost. The participant takes primary responsibility for the project and is awarded any patent rights for inventions that may occur during the demonstration. The government, on the other hand, ensures that schedules are met, costs are controlled and project objectives are met.

Jan 1, 1991

By Fathi Habashi

ION FLOTATION was introduced by F. Sebba in 1959. This technique permits the recovery of metal ions from solution through the introduction of an appropriate cationic or anionic surface-active agent into the solution. The surface-active agent, called a collector, is added in stoichiometric amounts in relation to the metal content of the solution. It reacts with the metal ion to form an insoluble soap, and is levitated to the surface by gentle bubbling of air to form a foam which collapses into an insoluble scum. The optimum conditions for the ion flotation with soaps of C10-16, fatty acids are shown in Table 15-1. Baarson and Ray (1965) found that once the metal was completely precipitated as the hydroxide, as little as one hundredth the stoichiometric amount of the collector was required to cause complete flotation of the [ ]

Jan 1, 1970

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By Enrique Farjeat P.

Mexico City's growth has encourage development of underworks to meet drainage and transport requirements. Deep Drainage System has been constructed through a complex tunnel network, 108 km in total, varying from 30 to 12 m in depth and 6.24 or 4.00 m in diameter. Wide range of stability conditions presented in soils has forced the use of several tunnelling methods, going from the manual procedure by the use of pneumatic tools, to slurry shields, or open face shields, with the aid of or without compressed air. For transport, subway tunnels have been excavated in very compact silty sands, 9.15 and 9.51 m in diameter, with the use of open shields one of which was designed by Mexican engineers as a prototype machine. This paper tries to describe evolution of tunnelling methods used in Mexico City during last 20 years.

Jan 1, 1991

By M. G. Rylatt

BHP Diamonds is developing Canada's first diamond mine, Ekati, located in the Northwest Territories (NWT). The mine is a joint venture between manager and operator BHP (51%), Dia Met Minerals (29%), Charles Fipke (10%) and Stuart Blusson (10%). BHP Diamonds is part of BHP Minerals: Production at Ekati began Oct. 14,1998. The mine is situated on a 3,450-km2 (853,000-acre) claim block located in the Lac de Gras region of the NWT (Fig. 1). It is about 300 km (185 miles) northeast of Yellowknife and 100 km (60 miles) south of the Arctic Circle. The seasonal winter ice road to Echo Bay's Lupin Mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.

Jan 1, 1999

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By Morley H. Mathewson

The unprecedented demand for capital investment in the mining industry today has intensified management's interest in every known technique which will help to reduce operating costs and increase production. One proven approach leading to the accomplishment of this objective is well known in the mining industry and is gaining added prestige, particularly where keen competitive conditions exist. This approach is in the area of incentives applied to mining productivity. An investigation of many incentive plans now in use throughout the mining industry revealed a predominant number of conventional type plans, Most of these plans are designed to reward the hourly-paid employee on the basis of percent over and above a standard hourly or daily ton rate, By contrast, this search failed to divulge any incentive plan solely and independently developed for production management employees. This does not mean that such plans in the mining industry are nonexistnet, but it does indicate that production management incentive systems are scarce or are being kept under wraps.

Jan 1, 1960

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By Chao Zhang, Wenhao Xia, Jianxin Fu, Ling Yu, Weidong Song, Yang Li

Sanshandao Gold Mine is the only undersea metal mine in China. To deal with the collapse and pumping of stopes and roadways caused by complex ore-rock occurrence conditions, the mine conducts filling and sealing of some areas, and the remaining ore reserves will be mined after treatment. Therefore, it is urgent to evaluate the stability of rock masses, fault fracture zones, and aquicludes during the secondary mining process. In this study, displacement and microseismic methods are employed to monitor rock deformation and fractures. Additionally, FLAC3D was used to simulate the process of secondary mining, reproducing the evolution of stress fields, displacement fields, seepage fields, and plastic zones at different mining stages. The combination of numerical simulation and on-site monitoring verification demonstrates that the deformation of surrounding rock presents a rapid growth at the initial stage of mining, followed by a gradual decrease in the growth rate, and finally tends to stabilize; the fracture zone area at the 151–159 exploration line on the − 320 m level (near the 7# and 8# stopes) exhibits poor stability, and monitoring measures should be strengthened; the deformation value of the aquiclude is less than the deformation value of I protection level in the Code for Design, the impact of secondary mining on the aquiclude is limited; fault and fracture zone deteriorate rock mass stability, and their impact is related to their spatial locations. Hanging wall fault has a more significant impact on the settlement of the aquiclude, while the footwall fracture zone has a greater impact on the development of the plastic zone.

Feb 21, 2024

By P. B. Altringer

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions1from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentration meets discharge standards.

Jan 1, 1992

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. Froth flotation is also widely recognized to be a very complex system having highly interactive and often self-compensating factors at work. Several summary articles have been recently published which discuss at length some of the important practical aspects of optimizing the use of existing commercial flotation reagents. Klimpel (1987). Klimpel and Hansen (1987a), Klimpel and Hansen (1987b), and Klimpel (1988). It is apparent from monitoring the industrial practice of sulfide mineral flotation over the last decade that considerable progress has been made in optimizing the operating aspects of flotation. For example, the availability of improved instrumentation and related computer devices, modified mechanical flotation cell designs, better reagent dosage control leading to less reagent usage per ton of ore, blending of feed ores, more attention to coarse and fine particle flotations, etc., are all examples of this progress.

Jan 1, 1988

By Steve Kral

The Prospectors and Developers Association of Canada (PDAC) was established in 1932 in response to proposed regulations that would have threatened prospectors in Ontario. From there, the association grew to represent the interests of Canada?s mineral exploration and development industry. The PDAC?s mission statement reads: ?The PDAC exists to protect and promote the interests of the Canadian mineral exploration sector and to ensure a robust mining industry in Canada. The PDAC will encourage the highest standards of technical, environment, safety and social practices in Canada and internationally. ?Today, the PDAC?s 6,000 individual members include prospectors, developers, geoscientists, consultants, mining executives and students. In addition, the association?s membership includes 950 corporate members, representing senior, mid-sized and junior mining companies in addition to organizations that provide services and equipment to the mining industry. In 2010, the PDAC adopted its e3 Plus principles, a framework to guide its membership in responsible exploration.

Jan 1, 2011

By B. E. Penrod

The main constituents of flat glass are the eight commonest elements of the earth's crust. Five of these, silicon, sodium, calcium, magnesium and oxygen are essential. Two more, Aluminum and potassium have beneficial properties. For colorless glasses iron is undesirable, in standard clear glasses a small amount of iron is tolerable, while for most tinted glasses iron is essential. These elements are present in glass as oxides and because they are so common there is no foreseeable resource shortage. The availability of supplies of materials at particular sites at prices which enable a glass manufacturer to be competitive may be another matter. In this paper it is intended to provide a historical perspective to the current situation, to contrast some of the traditional North American and European practices, and to progressively review some of the driving forces for future change and to attempt to assess their effects upon both raw material supplier and consumer.

Jan 1, 1994

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By R. Mattos, E. Calcina, G. Quispe, S. S. Kanchibotla

During blasting, rock breaks and moves but standard grade control practices do not adjust ore waste boundaries to cater for blast movement. Rock movement resulting from blasts can result in mischaracterization of grade boundaries resulting in ore loss and dilution. Ore loss takes place when ore is mischaracterized as waste and sent to waste dumps, and dilution occurs when waste is mischaracterized as ore and sent for processing. Las Bambas operations of MMG Peru, realized the economic impact of blast movement on ore loss and dilution and adjust ore boundaries using limited blast movement measurements. This is a step in the right direction but has limitations for everyday application. This paper discusses the advantages of disadvantages of current blast monitoring techniques and introduces an operational tool to estimate polygon movements for different blast designs and confinement conditions. Blast movement estimates from this new tool have been compared against the estimates from the current tools for several production blasts and the results were quite promising.

Mar 2, 2022

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By Milton E. Wadsworth, Jeffrey S. Thompson

The effect of an activator on gold dissolution in clear solution is examined using a rotating disk gold electrode. Steady state polarization curves for anodic dissolution of gold and cathodic reduction of oxygen indicate that the dissolution rate increases in the presence of the activator. The activator enhances gold disso­lution under standard cyanidation conditions; however, optimum activator concentration at the maximum dissolution rate is a function of the cyanide level. In the presence of an activator, the gold dissolution mechanism is controlled by surface kinetics and may be explained by a metal dissolution over-potential model. The dissolution rate with activator is higher than the dissolution rate at a higher cyanide concentration but without activator. The dissolution rate measurements indicate that 3 PPM of activator in a 500 PPM NaCN solution provides a higher dissolution rate than 1000 PPM NaCN alone. Activator technology may be a cost-effective means to reduce cyanide concentration.

Jan 1, 1998