Search Documents

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

By D. Elroi

This paper addresses the sharing of 2D and 3D data between GIS and mine planning software. Two-dimensional (2D) data, and now three-dimensional (3D) data as well, can be formatted such that both types of software can use, exchange, and display the same datasets. This increases the ability to share data between such groups as environmental, exploration, and mine planning. It overcomes shortcomings of mine planning software in areas of open database connectivity, spatial analysis, and data input and output. It also helps to overcome shortcomings of GIS software in the areas of geologic modeling, three-dimensional interpolation, and visualization.

Jan 1, 1998

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By G. R. Coonan

A number of famous studies have shown that house damage relates better to peak particle velocity than to acceleration or displacement. The relationship is true but doesn't go far enough. Why, for example, can construction shots go well above 1.0 or 2.0 inches per second without reportable damage? Recent studies have shown that vie must look at frequency and duration of an event in addition to amplitude. The complexity of measuring frequency, duration, and amplitude makes the average blaster in the field shudder. An even more excruciating problem is the need to obtain such data inside the building or residence in order to accurately predict the damage potential or human response to nearby blasting. The author reviews current research programs and suggests new areas of research necessary to help maintain a balance between complicated research requirements and simple field measurements.

Jan 1, 1980

By J. R. Carr

A crucial concern when implementing computer algorithms for geostatistical analyses on microcomputers is speed of execution. Kriging, in particular, typically relies on a Gauss elimination algorithm to solve for weights. Because such an algorithm is required for each estimate, the solution for weights can result in very slow program execution speed on a microcomputer. One approach to enhancing the efficiency of Gauss elimination is demonstrated herein. The upper triangle plus diagonal of the intersample covariance matrix is used in a modified banded Gauss elimination algorithm. Results show that such an algorithm yields approximately a two-fold reduction in execution time for kriging when the number of nearest neighbors used for estimation is large.

Jan 1, 1990

By B. M. Davis

The problem of assessing uncertainty in grade estimates has been a topic of research and debate since kriging was first introduced. Use of the kriging variance was originally touted as all that was necessary in order to produce confidence limits for grade estimates. Since then the prudence of using the kriging variance for confidence interval estimation has been questioned, and techniques such as the jackknife and conditional simulation have been proposed to develop "true" interval estimates. This paper compares the differences between interval estimates produced by the three methods and makes conclusions about the performance of confidence intervals produced by the different methods.

Jan 1, 1997

By Richard J. Robbins

This paper is presented with particular reference to the findings of the OECD Advisory Conference on tunneling held last July in Washington D. C. A great deal has been said about the Conference in the past few months, but it may be appropriate to review briefly the background and objectives of the Conference to better understand how the mining community can relate its underground excavation problems to the results of the Conference. OBJECTIVES OF THE OECD CONFERENCE The world demand for tunneling (the term tunneling is used here loosely to include almost all forms of underground excavation) is expected to grow at an in- creasing rate. During the decade of the ?70's, the demand is expected to at least double by comparison with the previous decade. Much of this increase in demand will be due to the rapid growth of urbanization around the world. As urban populations grow larger and denser, the conservation of surface land and the quality of the environment become more important. This aspect of the increasing demand poses a difficult challenge to those who must plan and implement urban development.

Jan 1, 1970

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By Kenneth S. Johnson

Oklahoma is the only; state in the nation that is currently producing iodine. The iodine is extracted from iodine-rich natural brines being pumped from deep wells drilled into Pennsylvanian sandstones in the Anadarko basin of northwestern Oklahoma. Woodward Iodine Corp., started in 1977, was the first plant in the United States built for iodine recovery since the 1930s. At present, three companies are operating four iodine-producing facilities in northwestern Oklahoma. The combined production of these facilities, 1,321,000 kg in 1997, is about 26% of the U.S. annual consumption. Iodine is present in concentrations ranging from less than 100 ppm (parts per million) to as much as 1,560 ppm in brines in various Paleozoic strata in the subsurface of northwestern Oklahoma; these concentrations are exceptionally high, and are well above those of any other known brines in the world. Strata with the highest iodine content in the area (Mississippian limestones) have low permeabilities, and thus would yield only small amounts of brine. On the other hand, the lower Morrow sandstones (Lower Pennsylvanian) have a relatively high permeability and are capable of yielding large quantities of brine that average 300-350 ppm iodine. The Morrow brine reservoir was deposited in shallow-water-marine and intertidal-shelf environments and now is buried 6,000-10,000 ft below the land surface. Production is localized to Morrow channel deposits confined to an Early Pennsylvanian paleovalley that is 1-2 mi wide, is about 70 mi long, and is referred to informally as the "Woodward trench." All three companies are producing iodine-rich brines from Morrow sandstones in three different parts of the Woodward paleovalley, and one of the companies also is extracting iodine from oil-field brines coming from several petroleum reservoirs near Dover, about 80 mi east of Woodward. The basic extraction method employed by Woodward Iodine Corp. was used in Louisiana and California operations in the late 1920s. This method is commonly called the air-stripping process. Lower Morrow brine containing dissolved sodium iodide is pumped to the plant through a series of pipelines, where by-product natural gas is separated and processed. The brine is then acidified and subsequently oxidized with chlorine to convert the iodide to iodine. The iodine is air stripped and reabsorbed with sulfur dioxide and water, converting it to hydriodic acid, or process liquor. The process liquor is then processed, using chlorine once again, to crystallize the iodine as a solid. This is then melted and frozen to form a solid product, which is packaged in 110-lb (50-kg) drums and shipped to end users throughout the world.

Jan 1, 1999

By W. Haupt, M. Thormé, H. J. Ertle, K. Reim

Though Germany has a very old mining history, her experience in uranium mining only started in the late sixties. Today in the Federal Republic of Germany (FRG) there are only 5 small mines in the exploration stage, namely Menzenschwand and Müllenbach in the Black Forest and Mähring, Popenreuth and GroBschloppen in northern Bavaria. In all these exploration mines much development is required to define shape and size of ore bodies. Mining engineers, government authorities and environmentalists alike are very much concerned about environmental safeguards and protection of mine workers against radon and its daughter products. Miners are affected by internal and external radioactive exposure. In general the external [f3]- and [µ] -exposures can be considered as small in comparison to the internal exposure and are therefore not discussed in this paper. The internal exposure is caused by the inhalation of radon and its daughter products and is relevant to the lung as the critical organ. The nobelgas radon is inert and does not from compounds with other elements easily. Contrary to the physical half-life of 3,8 days the biological half-life of radon is only 10 to 20 minutes. During the rentention time in the body only approximately 1 % of the long-lived decay products are retained in the system (SCHOGER, 1976). In this connection is it important that the radon resorption as well as the radon secretion varies individually and depends to a large extent on the age of the person (SCHOGER, 1960). RENOUX et al. (1978) have determined that the greatest part of the a(-activity in the air is attached to aerosoles with a diameter of 0,4/14. The radiation exposure of the lung by radon is negligible if compared with the exposure by short-lived decay products. For this reason one has introduced the concept of the potential [o](-energy (P) of the short-lived radon decay products, which means the total [ct]-energy, which is produced when an atom decays in the decay-series down to the long-lived lead-210. [ ] The unity of the potential [o]-energy concentration in the SI-system is 1 j/m3 air. In radiation protection however a specific unit is used namely the working level (WL): [ ] The WL-unit, though internationally recognised has not been introduced officially in Germany. Because of the large amount of tunneling still to be done in the FRG, the various mines departments responsible for safety and health in mining ask searching questions such as: - What are the laws governing radon emanation in tunneling? - Can workers be adeguately protected against radiation hazards? - How should one drive through high grade uranium ore? - What happens if the ventilation system breaks down?

Jan 1, 1981

By J. Hart, P. W. Conrad, S. Rosenthal, R. A. Hogan

The Mining Engineering Department at Montana Technological University (Montana Tech) has a new Mine Safety and Health Administration (MSHA) approved program for Part 46 and Part 48 mine health and safety training. The training program will utilize the facilities and faculty from Montana Tech’s Mining Engineering and Safety, Health, and Industrial Hygiene departments to provide superior mine health and safety training to the mining industry. The faculty of each department includes professionals with experience in safety training and the mining industry. The training program incorporates adult learning techniques and extensive hands-on activities in all training modules. The instruction will exceed MSHA requirements. The resources available on Montana Tech’s campus will be utilized to strengthen the training program providing the mining industry with a world class mine health and safety training program.

Feb 1, 2023

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By J. S. Ross

The significance and role of industrial minerals in Canada differ from those in the United States, The smaller Canadian industry has recently become well diversified and self-sufficient in most commodities, However, it depends on exports, principally to the United States, for much of its market, Imports are small, but imports of several basic products manufactured from industrial minerals are large. This nation is a leading world producer of asbestos, gypsum, sulphur, nepheline syenite, titania slag, potash and barite. It has reserves in asbestos for at least 30 years enough potash to supply the current world's needs for 2,000 years and sulphur reserves for 40 years of current world demand, One of the ilmenite deposits contains enough titania to supply the current world demand for at least, 25 years.

Jan 1, 1964

By P. Hornby, S. Henley

INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo • Medsystem

Jan 1, 1996

The purpose of the 3DOPT Program is to determine, starting from drill hole data, the optimum economic mining limits for an open pit. The economic limits are defined as those which maximize total profit, i. e. total mineral value mined less the total mining and milling costs, subject to the restriction imposed by the pit slopes. To accomplish this, the program employs the following: (1) A three dimensional matrix of equal sized blocks in order to file the engineering data and the cost/value data required to develop the profit figure for each block of ore/waste. (2) A graph algorithm developed specifically for optimizing these profits.1

Jan 1, 1966