Search Documents

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Stuart Lister

"When MacLean Engineering chairman and founder Don MacLean got the first question from a minesite about the possibility of addressing ventilation limits through incremental fleet electrification, he was intrigued. It was back in 2015, and the MacLean scissor bolter was already diesel-electric (jumbo trailing cable), so it made sense to him that if they could engineer a battery drive system for the unit’s tramming cycle, they would have the inaugural electric vehicle (EV) MacLean unit.At that time, there were not any entirely diesel-free hard rock mines in existence on the planet, and that remains the case to this day — although the Borden project in northern Ontario is progressing toward that goal (see page 33). This meant there was essentially zero market demand for battery electric vehicles as well as a complete lack of battery technology to address the battery electrification of heavy haulage. Heavy haulage is the part of a typical mine’s mobile fleet with the largest footprint when it comes to diesel particulate emissions, greenhouse gases and wasted energy in the form of heat.Three years later — the wave of battery electrification that is currently picking up speed across the mining industry promises to hit full swing by the early 2020s when a slew of new build, diesel-free mines will start construction. But this movement toward emissions-free mobile fleets is not a completely new phenomenon. Instead, it is an updating of mining technology from a previous generation. What is going on now is the re-electrification of mining. Up until the 1960s, early generations of battery technology (lead acid) and electric locomotive systems were the norm for material and ore haulage in Canada and elsewhere.The thought of a coming paradigm change in mining was particularly pertinent to Don MacLean back in 2015, as he had been part of the era that ushered in the first generation of rubber-tire diesel equipment, when he was a divisional foreman with Inco in Sudbury in the 1970s. He was part of the operating team that was tasked to build a rail loop on one extraction level of the mine. At that time, events on the ground overtook the project, as diesel-powered mobile equipment became a viable option. Once the first diesel scoop was introduced at Creighton #3 shaft, it was clear what the power, haulage capacity and mobility could do for operations and that era of electric rail haulage underground was effectively over."

Jan 10, 2018

By Jacob Carr, Rebecca Knuth, Emily J. Haas, Marvin Cheng, Bob Bissonette

Many industries, including mining, are experiencing an increase in the use of robotic and other artificial intelligence (AI) systems to improve efficiency, productivity and precision. For example, a 2023 survey showed that mining industry executives wanted to integrate more autonomous equipment to improve productivity and alleviate workforce shortages (Haas, 2024). This feedback was coupled with an increased appetite to advance the types and uses of automation and AI in the workplace. However, there is also an increasing concern about the ways that robotic applications may unintentionally affect worker safety. Humanmachine interaction poses potential risks, especially when industrial robots operate near workers in specific environments (such as drilling, handling and transporting materials, equipment inspection and lifting heavy loads). Research has explored the unintended consequences of introducing new technologies or processes in the workplace to include incidents such as being struck by equipment and challenges around data privacy (Lööw et al., 2019; Khurram et al., 2025; Haas and DuCarme, 2015; Almeaibed et al., 2021; Zio and Miqueles, 2024). More recently, the use of digital twin technologies and simulations (hereafter referred to as digital twin systems) has been boasted as a tool that can help prevent unintended consequences around worker safety by identifying and mitigating risks before a worker completes a task in tandem with a robot or other new technology. Digital twin systems produce a virtual replica of a physical environment or process (Almeaibed et al., 2021; Zio and Miqueles, 2024; Saes, 2024). To this end, this article explores the potential role of digital twin systems in enhancing safety within mining and other similar environments. It will primarily focus on environments where robots and human workers may interact, although digital twin systems can be useful with other technology applications. First, we define digital twins and digital simulation as components of a system. Then, we highlight possible applications of digital twin systems in mining to replicate real-world processes, followed by potential benefits of their use and where more research may be needed.

Oct 1, 2025

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By A. Johnson

When are SMART transmitters the smartest choice? To answer this question requires a closer look at SMART transmitter technology. It is necessary to understand this technology in order to recognize how it can best be utilized to give the greatest value for the application. And, once the decision to buy transmitters has been made, it becomes a question of whose SMART transmitter to buy. For, although the under-lying technology is similar, the differences that exist in how the technology has been implemented can make a dramatic difference in the end result. What prudent users of SMART technology do is to analyze their needs by application before making their buying decision.

Jan 1, 1988

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Mary Nelima Ondiaka, Kayode Henry Talabi, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau

Iron ore is essential in steel making; however, high-grade ores have diminished, making low-grade ores inevitable. These lowgrade iron ores need further beneficiation to upgrade the iron content. Currently, traditional physical and chemical methods are utilized and are not environmentally friendly. Bio-beneficiation techniques have emerged as a sustainable alternative for mineral recovery. This review delves into recent bio-beneficiation advancements for enhanced low-grade iron ore recovery using microbes. Research has revealed that bio-beneficiation methods such as bio-leaching, bio-flotation, and bio-flocculation have proven successful in iron recovery from ores. The bio-beneficiation process occurs in mild conditions using bio-reagents derived from microbes and offers a reduction of chemicals used in processing. Bio-beneficiation of iron ore potentially offers a relatively energy-efficient, cost-effective, and environmentally friendly method of maximum iron ore recovery. However, this review has identified a scaling-up difficulty in which a future approach for industrial-use applications is offered following a thorough sustainability assessment. Bio-beneficiation, using microbial processes, provides a viable avenue for maximizing iron ore recovery while tackling the constraints of dwindling high-grade iron ore resources and environmental sustainability.

Mar 16, 2024

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By P. Crouse, J. Obermeyer

"INTRODUCTION Site location and history The Holden Mine is a former underground copper mine that was developed and operated by the Howe Sound Mining Company (Howe Sound) from 1938 to 1957. The mine is located in north-central Washington State, U.S., near Lake Chelan in the area shown as Holden Village in Figure 1. Although Rio Tinto never owned or operated the mine, they are managing and funding a several hundred million dollar clean-up to prevent future water and soil contamination and to reclaim the former mine site under the United States Environmental Protection Agency (USEPA) Superfund process. The former mine included an onsite mill and a nearby housing complex for the miners. Howe Sound developed the mine as a series of near-horizontal drifts and tunnels, interspersed with stopes and shafts that connect different mine levels underground. The tunnels that were excavated to develop the mine total nearly 100 km in length.During development of the underground workings, Howe Sound removed more than 230,000 cubic meters (m3) of waste rock from the tunnels and deposited this material in two waste rock piles. Ore was processed from the mine in the onsite mill to produce a copper concentrate that was shipped off site for smelting. Roughly 10 million tonnes of tailings were produced as a by-product of the milling operation, most of which were deposited in three large impoundments (Tailings Piles 1, 2 and 3) directly south of and adjacent to Railroad Creek. Howe Sound closed the mine in 1957. In 1961, the property was transferred to Holden Village, Inc. (Holden Village), a not-for-profit corporation that maintains a year-round community and operates an interdenominational religious retreat in the former miners’ town. With the exception of the patented private land, the remainder of the Site is on National Forest lands and is administered by the U.S. Forest Service. The mine is remote. It is only accessible by boat or float plane from Chelan, Washington, up Lake Chelan to Lucerne, nearly 40 km. Vehicle access from Lucerne to the mine is provided through a 17.5-km-long winding gravel road that climbs 640 meters in elevation. The general site features are shown in Figure 2. Physical setting The Holden Mine is located on the eastern slopes of the Cascade Mountain Range at an elevation between 975 and 1,050 m above mean sea level. Holden Mine was developed adjacent to Railroad Creek, which lies in a glacial U-shaped valley carved into the igneous and metamorphic bedrock with steep-sided slopes (Figure 2)."

Jan 1, 2017

By Christophe Bragard, Rebecca Reeve

The Regional Connector Transit Corridor (RCTC) Project is a 1.9-mile-long metro light-rail extension project that traverses the historical core of downtown Los Angeles, California. This project aims to improve mobility throughout downtown LA with fewer transfers for riders. It is designed to connect two existing rail lines for a more seamless travel. The project consists of twin bore tunnels, three new stations, and is scheduled to be completed in 2022. The design-build contract was awarded to the Regional Connector Constructors (RCC) in 2014, a joint venture of Skanska and Traylor Bros, Inc. with Hatch Mott MacDonald as the designer. One of the challenging aspects of the project was the construction of a crossover cavern in a narrow public right-of-way surrounded by historical structures. RCC used Sequential Excavation Method (SEM) to construct the crossover cavern measuring 287 ft long by 58 ft wide by 36 ft tall. The initial lining of the cavern featured a 12 in. fiber reinforced shotcrete lining. The initial lining was separated from the final lining by a hydrocarbon resistant membrane, as specified by the standard requirements of Metro. The cavern features a cast-in-place final lining with a thickness of 5 ft 9 inches in the invert and 18 inches in the crown and walls. The structure also features a nonload bearing plenum slab and interior walls for ventilation.

Jun 13, 2021

By Lucy England

The following is a summary of the Robert E. Murray Innovation Lecture on “Sustainable Copper Mining Flowsheets and the MissionZero Mine” presented as part of the keynote session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT. As the world accelerates its transition to renewable energy, the appetite for critical minerals such as copper, lithium, nickel, rare earths and graphite has never been greater. Forecasts suggest that global mineral demand will double by 2050, driven by the proliferation of electric vehicles, renewable power infrastructure and digital technologies. This surge presents not only an immense opportunity but also an unprecedented challenge. In a world where every ton of ore processed and every liter of water used is scrutinized, how can mining deliver more with less, while meeting tightening environmental and social expectations? Traditional mining methods, developed for an era of abundant, high-grade ore and looser regulations, are struggling to meet today’s demands. Declining ore grades, volatile markets and the imperative to shrink environmental footprints have rendered traditional mineral processing practices unsustainable. The sector thus finds itself at a decisive juncture, caught between the need to fuel the green economy, defense and artificial intelligence (AI) infrastructure, without compromising the planet’s future. Balancing these competing demands requires a paradigm shift in technologies and processes. FLS has responded to this challenge with MissionZero: an ambitious, holistic initiative to develop flowsheets for the future of mineral processing. This systemic approach aligns operational excellence with environmental responsibility. Integrating innovative technologies, digital intelligence and commodityspecific process designs, it offers mining professionals a roadmap to meet both production targets and sustainability goals. At the center of this approach is the belief that a more sustainable mining requires more than incremental improvement; it demands a fundamental shift in how we extract, process and manage resources. By developing tailored flowsheets for copper, gold, lithium and tailings reprocessing, FLS aims to set a new standard for efficiency, circularity and environmental stewardship. The message is clear. We must achieve more with less: less energy, less water, less waste.

Mar 1, 2026

By R. Kramer, A. Habibi

A ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system includes three intake and six exhaust shafts, and three surface axial fans ventilate the mine in a blowing configuration. Airflow quantity, pressure losses and air psychrometric characteristics were quantified, and the influence of moving cages and skips in the shaft examined. The benefits of utilizing high-accuracy digital pressure transducers and advanced psychrometers were seen when undertaking a “leapfrogging” survey to gather data needed to build a computer ventilation model. Two underground booster fans with VFDs are idle but available at the mine. The ventilation model was used to determine the optimal booster fan locations to decrease operating cost by reducing the load carried by the main fans. A leakage study was conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next 15 years of mine operation and investigates the effect of proposed scenarios.

Jan 1, 2014

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975