Search Documents

By A. W. Dickerson

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research, Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Jan 1, 1997

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By Steve Kral

The concept of sustainable development is not new to the mining industry. Many people involved with mining have argued that the industry throughout the world has always supported the communities where they operated. They say that the mining industry was employing sustainable development practices before the phrase became fashionable. The mines employed residents and supported the local economy through tax payments and the purchase of goods and services from local businesses. In many cases, mining companies have built medical facilities and contributed money, equipment and services to local schools. In modern times, mining companies have donated reclaimed land to the local communities for use as parks and recreational facilities.

Jan 1, 2004

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor's greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990

By Muhammad Zia-ur Rehman, Sajjad Ahmad Baig, Gao Lei Fu, Muhammad Mohsin, Sobia Naseem

The environmental sustainability is linked back to human sustainability; the sustainability development comprises the environment, society, and economics. This study mainly focused on mining sustainability and its impact on the environment of Pakistan. For measuring the level and environmental mining sustainability nature to Environmental Impact Assessment (EIA) of the world’s second largest salt mine “Khewra,” Folchi and Phillips environmental sustainability mathematics (PESM) models are applied. The results indicated that Khewra was deemed to be potentially sustainable for the environment and quality of salt. The results suggest the delicate balance of maintaining sustainability successfully, regarding the mining process in Pakistan which has been affecting the local environment and community so badly. The paper lays emphasis on the potential significance of the model’s application for the attainment of sustainable mining goal. This study is essential for researchers,

May 11, 2020