Search Documents

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By Adrian Coombs

The York Durham Sewage System (YDSS) Interceptor Tunnel Project is located in the Town of Richmond Hill, Ontario, Canada, just north of Toronto. Construction commenced in September 2006 and completion is planned for early summer, 2008. The project involved public and agency buy-in of construction technologies and methods that minimized dewatering, design and construction of sealed shafts with jet grout break-in and out blocks in order that Earth Pressure Balance (EPB) mode could be maintained by the Tunnel Boring Machine (TBM) during shaft entry and exit. This paper will discuss the advances that were made possible through the opportunity to apply and test these technologies in order to accommodate the aquifer and artesian conditions present on this project.

Jan 1, 2008

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By R. M. Schuster, F. M. Benavides

Samuel G. Bonasso The article by Benavides and Schuster provides an in-depth study of three transportation alternatives for a four-mine complex in western Kentucky. The examination of aerial tramways was not undertaken as an alternative solution. We feel this is an oversight since industrial ropeways are competitive with both belt conveyance and overland truck hauling. In fact, there are aerial tramway systems, operational today, which are 100 years old and operating with some original components. Maybe unfortunately, there are no fixed rules or guidelines whereby the most cost-effective means of transporting and handling material for a given situation may be selected. Each situation must be evaluated so the variables that influence the selection of the desired alternative can be clearly defined. However, there are in-place industrial ropeway systems that have proven economically feasible over a range of 1.6-50 km (1-31 miles). The more difficult the terrain, the greater the cost efficiency.

Jan 1, 1983

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

Recent accelerated exploration efforts in southwest China have progressively quantified the vast phosphate resources in the Yunnan Province. To date, according to Chinese geologists, potential reserves in the province may be on the order of 4 Gt, which would equal the entire US reserve base. Development of this vast reserve is underway at two sites located 60-70 km southwest of Kunming, the provincial capital of Yunnan. The first, the Kunyang open-pit phosphate mine, produces an estimated 1.5 Mt/a of 22-30% P20,5. The other project located north of Kunyang is the Haikou mine, which the Chinese consider a possible 2.0-Mt/a operation. Because average ore grades run 3% less than those of Kunyang, beneficiation will be necessary. While the latter project has been initiated on a small scale, it is basically still on the drawing board. Brown and Root and the US Bureau of Mines are assisting on the project. Both operations are under the direction a regional administration which reports to the Ministry of Chemical Industries in Beijing. Combined production from both mines could represent some 70% of China's future productive capacity. Ore reserves in the region are estimated at 400 Mt by local officials. Geology of the District The phosphates are considered Cambrian in age and rest on a Precambrian dolomite. The Indian Ocean, Chinese geologists say, may have been the original source. The line of deposition stretches on a trend from Vietnam in the southwest, through Yunnan, into Sichuan Province to the northeast. Because the area is considered very stable from a geologic viewpoint, large quantities of phosphate have been deposited and large outcrops are known to occur everywhere in the province, according to Chinese sources. The Kunyang and Haikou ore bodies are thought to be two wings of an anticline with the former the southern portion, and the latter the northern portion. Each ore body strikes on an east-west axis. While there are many localized phosphate operations throughout the province, the Kunyang mine is the premium producer. Kunyang's Mining Development The Kunyang open-pit mine was opened in 1966. During the early years, operations were considered somewhat disorganized. Systematic mine planning and normal operations were not initiated until just two years ago, according to mine management. In 1979, Kunyang finally reached its design capacity of 1.5 Mt/a. The ore body consists of two phosphate beds separated by a band of shale. The top layer of phosphate varies from 4 to 8 m, averaging 6 m. The middle shale layer is 2 in. The third layer, which is not as rich as the top, is approximately 4 m. To further complicate matters, the ore dips 15° to the south over a strike length that is currently undefined, but believed to be

Jan 3, 1980

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By Margaret Armstrong

The increasing cost of developing new mines and the need to mine more marginal deposits have led mining companies to use more sophisticated estimation methods such as kriging. But until recently, coal mining companies have shown little or no interest in these techniques. However, the stringent quality controls which are now placed on coal have led to a surge in interest in improved estimation methods. This can be seen from the -, number of research projects by private companies and governmental agencies on the application of geostatistics to coal reserve estimation. At present, most of these programs are centered on the problem of estimating the tonnage and the average grade (i.e. ash percent, sulphur content, calorific value, etc.) of the coal in-situ. See, for example, Sabourin (1975), Woods (1976, 1979), Pauncz and Nixon (1979) and Armstrong (1980). These studies show that the established techniques of linear geostatistics can be applied successfully to coal deposits. The study by Woods is particularly interesting because he had access to the actual production figures as well as the initial sample data from the no 2 seam in the Greenside Colliery owned by the Anglo-American Corporation. He showed that the estimates obtained by kriging were consistently closer to the actual production figures than those given by three other estimation methods. This confirms the superiority of kriging as a method of estimating block values for coal. Another advantage of geostatistics is that it can be used to determine the optimal spacing between drill holes. An example of this is given by Armstrong for the coking coal deposit in the Bowen Basin, Australia.

Jan 1, 1981

By Jue Kou, Hongda Xu, Tichang Sun, Shichao Wu, Wenli Han

To investigate the effect of simultaneous change in particle size of raw materials (including ore, reductant, and dephosphorization agent) on the direct reduction process of high-phosphorus oolitic hematite, the experimental research of method with direct reduction and magnetic separation was conducted to investigate the effect of simultaneous change in particle size of raw materials on the final reduction products in the form of mineral composition, reduction speed, metallic iron particle morphology, phosphorus distribution, and powdery reduction iron. The results revealed that under the same conditions of reduction temperature, the raw material particle size affects the mineral composition of the final reduction product, the coarser the raw material particle size, the slower the reduction speed, the lower the metallization rate, and the larger the final metallic iron particle size formed. Under the same conditions of raw material particle size, the reduction temperature affects the mineral composition of the final reduction product, the higher the reduction temperature, the faster the reduction speed, the higher the metallization rate, and the larger the size of metallic iron particles within a certain reduction time. Neither the raw material particle size nor reduction temperature affects the form of phosphorus present in the reduction product. Both the raw material particle size and reduction temperature affect the grade of powdery reduction iron to a less extent, but affect the recovery rate and phosphorus content significantly. At the same reduction temperature, the recovery of powdery reduction iron and phosphorus content gradually decreases with the increase in raw material particle size. For the same raw material particle size, the recovery of powdery reduction iron gradually increases, and the phosphorus content gradually decreases with the increase in the reduction temperature. The results identified the effect of simultaneous changes in particle size of raw materials on the direct reduction process of high-phosphorus oolitic hematite and provide a basis for the selection of raw material particle size for the industrial application.

Dec 20, 2022

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002