Search Documents

By D. M. Thayer

Laboratory and pilot plant investigations have indicated that copper recoveries of 50% can be achieved with fine grinding and flotation of a copper reverberatory furnace slag, Microscopic and microprobe studies indicate that the recoverable copper is in the form of matte, chalcocite, and metallic copper; the percentage of copper in particles appearing to be copper-free was from 0.23 - 0.54%.

Jan 1, 1969

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By A. A. Davis

The decade of the 70?s saw a series of landmark environmental resource programs enacted by the Congress. Many states followed suit, so that by the end of the decade air quality, water pollution, and the conservation of other natural resources, including minerals, were the subject of a wide-ranging body of laws, policies, regulations, and procedures. Many of the actions required or permitted by this rule-making involved areas for which adequate information and substantial experience were not available. Moreover, goals and objectives were sometimes established which were enormously difficult to achieve technically, or of such formidable expense as to cause concern about their consequences in the marketplace. It is therefore hardly surprising that one product of all this activity has been a mass of litigation. Court dockets are crowded with suits and counter-suits involving both substantive and procedural aspects of environmental protection. Indeed, it is probably fair to say that the volume and range of environmentally-related disputes brought before the courts parallels that generated by the civil rights movement a decade ago. There were also some new dimensions to the environmental movement. For the first time, the national environmental policy act required agencies to prepare environmental impact statements when proposed projects or activities would have substantial impacts on environmental resources. Another requirement of many of the new programs mandated meaningful citizen participation in public decision-making. Here, as elsewhere, the purpose was admirable, but guidelines were vague, and the result often was inaction, polarization, and litigation.

Jan 1, 1986

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Klaus Rieker

The main train station of Leipzig in Germany is currently being upgraded from a head station to a partially thru station. In order to achieve this, significant ground improvements are necessary. Soil freezing for example is used to create the excavation box retaining walls. The freezing works will be carried out from two tunnels with an inner diameter of 2.4 m (~ 8ft). The tunnels were constructed by the pipe jacking method. The cutter head of the machine was equipped with discs and scrapers. Driving and excavation was carried out using a bentonite supported face. Due to the small arrival shafts, the machine had to be lifted out in components. The essential limitation of settlements during the drives was achieved even better than expected.

Jan 1, 2008

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By K. R. Weller

In recent years, a variety of new or substantially modified grinding machines have been offered to the mining industry with claims of improved performance relative to standard grinding machines especially rod and ball mills. The incentive for developing such new machines is high, because costs associated with grinding are a very substantial part of the total costs of processing run-of-mine ore, and gold ores are no exception in this regard. The incentive is also high because of the very low conversion of input energy to comminution energy in most tumbling mills. If the most energy-efficient means of mechanical size reduction is slow compression of single particles, then this energy amounts to only about 3% of that used in tumbling mills. It would seem, therefore, that there is a huge potential to do better. This paper examines three types of grinding machine for which claims of higher energy utilisation ( amongst other beneficial claims) have been made, namely the high pressure grinding rolls, the vibrating drum mill and various styles of stirred mill. It presents evidence concerning the claims, examines the range of particle size and particle size reduction over which benefits might reasonably be expected to accrue, discusses the major issues in contention and briefly describes the research the CSIRO Division of Minerals has in progress, both independently and collaboratively, the latter mainly with the Julius Kruttschnitt Mineral Research Centre (JKMRC) via the Cooperative Research Centre for Mining Technology and Equipment (CMTE) and the Australian Mineral Industries Research Association (AMIRA). There are many criteria which may be chosen to assess relative performance of grinding machines. Those used below are:

Jan 1, 1995

By Hal McVey

Introduction The role of marketing in the minerals and mining industry takes on different degrees of importance depending on the commodity, but nowhere are sales and marketing more important than in industrial minerals. This article compares industrial minerals marketing with the marketing of other mining and mineral products. Marketing in Mining Some broad generalizations on the marketing of industrial minerals in relation to other mineral products can be made without getting bogged down with exceptions to generalizations. Two totally different areas of mineral production are crude oil and natural gas, and metals, including ores and concentrates. Although these commodities are the basis for two completely different industries, they share two things in common from a marketing standpoint: • Their value per unit volume is usually high enough so that they can be transported great distances. • Their specifications are readily definable and, therefore, the quality of a standard product from a production run can be communicated by stating certain chemical and physical features. This permits sales to be consummated by telephone, telex, and letter, without the need to pretest the products under use conditions. In regard to the first item, industrial minerals, as opposed to oil, gas, and metals, are in most instances site specific. Location of the point of production in relation to the point of use is of paramount importance based on a generally lower unit to volume value. This means that transportation is a major factor, with the cost of getting the mineral to market commonly exceeding its f.o.b. value. Coal marketing has many characteristics in common with industrial minerals. Coal sales can es-

Jan 11, 1983

By James G. Tilton

Throughout the world, sedimentary basins are exploited for many different minerals. Frequently, the extractive methods conflict with one another. A case in point is the proximity of oil and gas operations and the mining of coal. Generally, the interference between the two industries lies in the fact that the reserves over- lie or underlie one another. Mining of coal generally is developed on a rectangular pattern in a horizontal mode while oil and gas drilling is developed on a radial pattern in a vertical mode. Coal mining has exhausted vast acreages in various basins with many of those basins being drilled for oil and gas. Those existing wells create problems by requiring the unrecoverable coal pillars to support the well bore, or to make special provisions in order to mine through an existing well. The system works ... more or less; but there are little or no provisions made for additional drilling unless the vast majority of those new wells are drilled through mined-out sections (gob) of those mines. Many states have rules and regulations governing the drilling of oil and gas wells through gob; but, some companies and some regulatory agencies or personnel have deemed such drilling as a hazard to the mining operations. This paper explores the history, technical standards, and safety aspects of drilling oil and gas wells though the gob of worked-out and active mines. It is the opinion of the author that such drilling can be conducted safely while eliminating the re- quired changes in mine projections and the loss of recoverable coal in the form of well pillars.

Jan 1, 1997

By M. Dosemeci, M. McCawley, J. McLaughlin, Z. Wu, F. Hearl, W. Blot, K. Peng

Proposals have been made by two organizations, the International Standards Organization (150) and the American Conference of Governmental Industrial Hygienists (ACGIH) for a revised respirable dust criteria and criteria for thoracic and inspirable dust. These criteria yield different results than criteria based on lung deposition patterns in assessing the hazards due to dust exposure. Since these differences are a function of the size distribution of the dust an analysis of dust size distributions from various mining operations was performed to determine the amount of difference that could occur. The dust size distributions available for this analysis were taken from U.S. coal mines and from Chinese metal mines. The mass of mechanically generated dust that will deposit in the alveoli was found to be in direct proportion to the ISO/ACGIH criteria estimates in the mines studied. Therefore, respirable dust estimates for substances such as coal and silica are not a problem. Estimates of exposure to diesel exhaust in these mines, however, were not always in the same proportion to the estimated alveolar deposition. Also, concern with an excess of bronchitis among miners may not be adequately addressed by the use of samplers conforming to the ISO and ACGIH criteria. The cascade impactors used to acquire the data for this analysis require four to eight substrates per sampler. For daily dust exposure assessment this method is cumbersome and time consuming. Therefore, two new samplers have been designed to meet the need for determination of deposited dust mass. These samplers follow the lung deposition curve rather than the penetration curves proposed by the ACGIH and ISO and require analysis of only two substrates per sample.

Jan 1, 1992

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. A preliminary indication of the repeatability of a simplified alternative method (MN DNR method) was assessed and results from the MN DNR method were compared to those from the ASTM method. To provide an indication of repeatability, six samples from three different rock types were subjected to dissolution testing for periods of 20 to 68 weeks. Drainage pH values at the end of the tests were within 0.5 units in all cases and within 0.05 units in four cases. The percent difference from the mean for overall sulfate rates from paired cells ranged from 0.04 to 1756, with a median of 6.3%. Nine samples from four rock types were subjected to both MN DNR and ASTM tests for periods of 20 to 132 weeks. The difference in final drainage pH values forsix of the samples was less than 0.1 unit, and these values were less than pH 3.65 or greater than pH 8.0. The final drainage pH difference for the last three samples ranged from 0.15 to 0.4, and these values were ill the pH range of 6.2 to 7.2. The sulfate release rates for the periods of record for the MN DNR method were 70 to 150% of those for the ASTM method, with a median value of 110%. Sulfate and calcium release from the two methods was not substantially different. The MN DNR method typically produced higher magnesium release.

Jan 1, 2000