Search Documents

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By K. Whiting, R. Huffsmith, R. Olsen, D. Adams

Long-term closure alternative selection for heap leach pad effluent is a daunting task. Passive water treatment, if designed with enough long-term capacity, can minimize long term O&M while meeting water quality objectives. Leach pad effluent from a 30-acre leach pad at Basin Creek Mine, Basin, Montana was targeted for long-term water treatment using a passive water treatment system. The objectives and results of design and construction are: 1. Design a long-term passive system utilizing existing infrastructure. 2. Construct a field scale pilot test at the mine site.

Jan 1, 2002

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By D.G. Osborne

Each month abstracts of the papers selected for the Annual Bound TRANSACTIONS Volume will appear on this page. Since the Annual Bound Volume will not be published until the spring of next year, this will give people an opportunity to order copies of the papers earlier. If you would like copies, fill out the coupon below and return it to SME-AIME. Each copy will cost

Jan 1, 1985

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By W. Langer

Of the 50 or so most often utilized industrial minerals, more than two thirds are, or have been, produced in the western states of Arizona, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah, and Wyoming. Some commodities, such as natural aggregate, currently are produced in all 13 states; others such as beryllium and iodine are produced in only Utah and Oklahoma, respectively. Together, the 13 western states make a significant contribution to the US industrial minerals industry.

Jan 1, 2007

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology&apos;s development.

Jan 1, 1999

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006