Search Documents

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors' experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

Arizona copper mines produced nearly 67% of the nation?s copper in 2000, according to a report released by the Arizona Mining Association (AMA). This was a slightly larger share than in 2000 despite large reductions by one major copper producer and production cutbacks at several other facilities. In 1999, Arizona mines produced 64% of the nation?s copper. The report was prepared by economist George F. Leaming of the Western Economic Analysis Center in Marana, AZ. It also showed the copper industry had a $4.6-billion impact on the Arizona economy in 2000, a 26%decline from 1999. This is the lowest financial impact since 1973 and less than half the record reached in 1981of $9.6 billion. The decline is primarily due to a sustained low copper price and a slow-down in the US economy. The mining industry?s impact included combined direct and indirect contributions of $1.283 billion in personal income for Arizona residents, the equivalent of 43,000jobs. More than 5,000 of those jobs were in state and local government and more than 18,000 were in trade and ser-vice businesses. The copper industry directly employed fewer than 8,000 people statewide in 2000. This was down about 23% from 1999.

Jan 1, 2001

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

This paper summarizes the practical considerations of the various electrical separation methods used in mineral processing. The effective factors related to mineral characteristics and equipment attributes are described and analyzed with reference to conventional industrial applications of the electrical methods. Some new aspects of electrical methods application and their potential for mineral beneficiation, apart from the mineral systems that have been successfully beneficiated, are also presented. In addition, wet dielectric separation, which now appears to be promising, is briefly cited.

Jan 1, 2000

By William A. Turcotte

Introduction The need for water is fundamental to every minerals processing operation. Though this may sound rather elementary, it is one area that cannot be over- looked. Frank C. Quinn in his paper entitled "Water Is Water Is Water" (1967) said, "but it isn't as simple as that. Very often research is slowed down and production is hampered because of a lack of appreciation for the behavior of water." The quantity of water needed for any operation is determined from bench and pilot plant testing. The quality required by the process for both fresh and reuse water is also established during these two testing phases. Quinn's statements are true whether the process involves the paper industry, the minerals industry, or any other industry. It is not the author's intent to cover water quality, quantity, or re- cycle in specific terms, but to provide the reader with a general outline of the topic with reference to several valuable sources of information. The first part of the chapter will cover several of the areas that have been de- tailed by others and also provide a list of reference sources. The references at the end of the chapter are not all inclusive but will provide a good starting point. In the second part of the chapter, a detailed description, with flowsheet illustrations, is pro- vided on the evolution of the reclaim (reuse) water system at the Tilden concentrator. Mineral Industry Water Needs Beresford and Edler (1978) surmnarized the minerals industry's need for water this way: "minerals are necessary to a modern complex technological society. The minerals industry, while its water needs are relatively minor compared to large users such as agriculture, nevertheless requires a large quantity of water to carry out daily operations from mining to final product refining." In 1973 total water use in the United States was estimated at 15.14 billion cubic meters (4 trillion gallons) for the minerals industry. Of this, about 69% was recirculated within the system. In 1982 Watt and Horton stated that the percent of recycled water in the minerals industry had improved to 73%, showing the minerals industry is an efficient user of water and that steady improvement in water recycling is something the minerals industry can look to with pride. The percent of water needed by the United States' minerals industry was estimated in 1962 to be about 2% of the total water required by industry

Jan 1, 1986

By A. Wahab Khair, Negendra P. Reddy

INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982). One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Elorgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cy to toxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le ?oux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly . Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles , of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield,

Jan 1, 1986

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

My "outside exploration" began in November 1908, only 16 months after I had come to Bisbee as a raw engineer. The well publicized reputations of eminent engineers up to that time, including John Hayes Hammond, Herbert Hoover, James Douglas, D.C. Jack- ling, J. Park Channing, and a few others had been due to new mines they had found or brought to successful operation. And here was I, a mere youngster, given a chance to join the group. I knew there would be disappointments but I had no idea how many of them. In spite of the many prospects that turned out to be worthless I never looked at a new one without the feeling that this one might turn out to be the big success. This confidence, blind as it was, gave every arduous examination a zest and it made me climb every mountain on which the owner said there was something worth seeing, or on which T could see a distant staining that might mean ore. If I looked at every showing the owner suggested he at least would think I was honest and would bring other properties to our attention. This reputation of never refusing to go to see an outcrop, no matter how hot the desert sun or how rough the terrain, was probably one of my best assets. High as my hopes were at the start, they proved not to be exaggerated and if I were given a chance to do it again I would not hesitate, in spite of the jaundice, rheumatic fever, and other maladies that beset some of the expeditions. On the whole the results have equaled all my hopes. Toward the end of my years of active exploration I totaled up the score. Out of the prospects submitted to us about two out of three were eliminated after questioning the owner or prospector, without an examination. This left about a 1000 mines or prospects that seemed worth at least a preliminary look. One out of seven of these was worth a little development and a seventh of this seventh turned out to be a modest success or better. And nine or ten in all, or one out of 1000

Jan 1, 1976

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986

In 2011, the value of mineral production increased in the United States for the second consecutive year (Table 1). Production increased modestly for most mineral commodities mined in the United States, and price increases, especially for precious metals, resulted in increases in the value of production. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates. U.S. apparent mineral consumption (industrial) of 11 mineral commodities decreased substantially from 2005 to 2010 (aluminum, cadmium, cement, copper, iron, lead, salt, soda ash, steel, tin and zinc). Data for 2011 were not calculated, but the data show a sustained decrease (especially for the metals) preceding the recession through 2010, so consumption seems to be behaving differently than production and GDP. After continued decline following the 2008?2009 recession, the construction industry began to show signs of improvement during 2011, with increased production and consumption of cement, construction sand and gravel, and gypsum ? mineral commodities that are used almost exclusively in construction. Crushed stone production, however, continued to decline.

Jan 1, 2012

By Jacques Bernazeaud

Rouez is a recent discovery of a major low-grade sulfide body (± 100 m, 0,6 % Cu, 0.3 % Pb, 1 ,5 % Zn, 21 g/t Ag, 1.5 g/t Au) in a populated farming area of Brittany, France, some 30 kilometres northwest of Le Mans. The discovery is the result of an airborne electro- magnetic (INPUT) survey. It is the first time that the INPUT method has been used in France. The survey Gas successful in spite of the numerous interferences normally found in populated areas. The lack of a good drainage system would not allow the discovery of Rouez using stream sediment geochemistry alone. Ground geophysical surveys confirmed the airborne work and gave sufficient information to make the first hole a discovery hole. The deposit is Proterozoic in age and sediment-hosted. The metamorphism is low grade.

Jan 1, 1983

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

By Ulises Deveze T.

The coal company Minerales Monclova, S.A. (MIMOSA), the owner of the Mimosa R Line, is a subsidiary company of Altos Hornos de Mexico, S.A., the largest steel plant in Mexico with an annual capacity of 2.5 million metric tons of steel ingots. The raw material's which are used in the steel plant are provided by the following companies: La Perla Minas de Fierro, S.A., iron ore; Cia. Minera de Guadalupe, S.A., Cia. Carbonera La Sauceda, S.A. Cia. Minera La Florida, S.A., and Minerales Monclova, S.A., which provide the coal used for coke, and altogether constitute the industrial group AHMSA. The coal property of Minerales Monclova, S.A. is located in the Sabinas coal area in the northwestern part of the Sabinas basin.

Jan 1, 1974

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By Stephen Slot Odgaard, Simon D. Taylor

Phase One of Copenhagen Metro opened on October 19th, 2002 and is already a great success. 11 stations are open and Phase Two with 6 additional stations will open during 2003. Phases One and Two include 21 km dual track, whereof 10 km is in tunnel. 17 stations (six deep, three shallow, and eight above ground) will service passengers with trains running at 90 seconds intervals. This paper will discuss the various aspects of the Metro, where construction methods include TBM bored, NATM, Cut & Cover, Secant Piles and Diaphragm Walls.

Jan 1, 2003