Search Documents

By Claus Becker

The new, 2.600 m long pipe under the river Elbe in Hamburg/Germany required for 2 traffic lanes, emergency lane and space for utilities a boring diameter of 14,20 m(46,6 ft). According the geology (glacial deposits consisting of clay, sand and marl, all containing big boulders) a Slurry-Shield with crusher was selected. With a minimum cover of 7 m and a maximum pressure of 5,6 bar extensive ground treatment was necessary to make the drive feasible. The machine contains a lot of new developments. The drive was finished in spring 2000 so all experiences can be reported. A special risk sharing contract avoided completely litigation.

Jan 1, 2001

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

By R. L. Ziegfeld

It has often seemed to me that people are too prone to turn to new and untried materials in an effort to solve their problems, without giving sufficient consideration to the old stand-bys, except as a last resort, It?s a little like middle-aged men who are swept off their feet by the fresh beauty of a young girl without first considering the many advantages that a more mature woman has to offer. Maybe it?s because, like the older woman, the older materials have to make a determined effort to keep themselves looking young and attractive. T at?s just about the situation with which the lead industry is laced. We have to make a determined effort to keep lead looking young and attractive to industry. However, there is one difference and it is important, Lead can not only be kept looking young, but it can, in fact, actually be kept young, This results from two things. First, industry and technology are constantly changing. For example, we have known for years that the density of lead makes it ideal to stop gamma rays, but it is only recently that atomic fission as a source of gamma radiation has become an important tool of industry, That makes old knowledge about lead useful in developing a new market for it.

Jan 1, 1958

By Takaji Kusakawa

In Japan, almost no natural gypsum is mined for industrial uses of gypsum, and almost all gypsum is synthetic gypsum, that is desulphogypsum, produced by waste sulphur dioxide gas from metal smelters and power plants, and other industrial waste sources. The amount of such sythetic gypsum production has reached more than six million metric tons per year (1979). Major uses are for cements and building materials. Other uses are soil conditioner, investment casting mold, organic composite materials, etc and sulphur recovery by gypsum decomposition is being examined. This paper summarizes present Japanese production and uses of sythetic gypsun produced from industrial waste.

Jan 1, 1982

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By Y. C. Kim

An alternate development drilling strategy to the one currently in use at the nine was investigated using geostatistics for a portion of the pit. The study area consisted of 4,000' x 5,000' in plan and 1,080' in elevation. The massive orebody, the three-dimensional nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy, as compared to the two-dimensional tabular deposits such as coal deposits. Rather than using the confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from this study showed that a total of 50 DDHs rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. This paper also emphasizes the importance of the particular objectives being used in development drilling and how they influence the "optimai" place- ment of the development drill holes.

Jan 1, 1981

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By F. H. Deily

The petroleum industry has developed and utilized many aspects of rock mechanics, both in its search for petroleum and in its drilling and production operations. Geological exploration activities have been improved by knowledge of earth tectonic forces. Better understanding of seismic wave motion has contributed to a more accurate interpretation of geophysical data. Drilling activities have benefited from basic knowledge of rock strength behavior under in situ conditions. Production has been significantly increased through stimulation techniques, such as hydraulic fracturing. The ability of rock mechanics work to contribute to future petroleum activities will depend upon the development of knowledge of rock properties under greater depths and at higher pressures and temperatures.

Jan 1, 1969

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Syd S. Peng

The key design parameters of roof bolting using expansion - shell type support for underground coal mine roof support are bolt length, bolt spacing, installed load and anchorage capacity. Depending on the utilization of suspension effect or friction effect, the bolt length is dictated either by the distance between the roof surface and the first overlying strong strata encountered or the desired magnitude of reduction in bending stress at the roof surface, The current prevailing practices about the bolt spacing and installed load are that an initial torque of 125 - 170 ft-lbs is applied and the bolts are spaced at 4- or 5- ft. square grid pattern. This seems to be a rather broad generalization in view of the great geological variances which are expected in underground coal mines. A modest evaluation program to measure the effectiveness of current roof bolting practices is to monitor the load history of roof bolts during a complete mining cycle including the phases of room development and pillar robbing. The load history, when compared with the anchorage capacity of roof bolts determined by in-situ pull tests, will provide information for evaluating the installed load, the bolt spacing as well as the specifications for structural and anchorage characteristics of the bolt assemblies. This paper presents a case history of monitoring the complete load histories of roof bolts in an underground coal mine of Pittsburgh seam.

Jan 1, 1976

By W. A. Haley

Wheel loaders were first introduced shortly after World War II as small machines designed for handling loose materials in various industrial and processing applications. It was not until the early 1950?s, however, that machine size permitted widespread loading of loose or stockpiled material into on-highway type trucks. An ever increasing number of machines continue to be used for this purpose today. In fact, it is by far the major use for wheel loaders in mining and quarrying. Many of these loaders were working at mines or quarries handling in-process or finished material and some were doing shovel clean-up. It was quite natural then, when the primary pit loading shovel was down, to attempt to maintain some production by replacing it temporarily with the wheel loaders. Most of these attempts were not very successful, however, until the really large wheel loaders, 4- to 6-yd. size were introduced in the early 1960's. Since that time these machines have proven they can be productive and economical primary pit loading tools, a job that was once the exclusive domain of the power shovel. To be competitive with the shovel however, conditions must exist or be made to exist, that will be favorable for the wheel loader.

Jan 1, 1967

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995