Search Documents

By E. H. Cho, Q. Luo

Pittsburgh No. 8 coal, cleaned by conventional froth flotation, was oxidized in a 2-L Parr stirred bench-top autoclave. Autoclave tests were carried out for up to 5 hrs under the following conditions: 150 to 225ºC, 60 to 500 psi 02 and 15 to 60 g of coal per 600 mL of distilled water. The oxidation of coal was evaluated by measuring the total acidic group formed on the surface of the coal and by measuring the adsorption (under standard conditions) of calcium ion from a solution. The degree of oxidation of the coal increased continuously, without much leveling off, with increasing oxygen pressure. With increasing temperature, the oxidation of the coal increased sharply between 150 to 175ºC and then leveled off above 175 °C. The adsorption of calcium was >3% on coal oxidized under the most favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The loss in Btu was found to be sensitive to oxidation temperature. This study concluded that the optimum oxidation of coal is achieved over 3 hrs at high oxygen pressures (e.g., 500 psi) at ~170ºC. This study also concluded that, when measured in terms of calcium adsorption, Btu loss and reaction time, the oxidation achieved in an autoclave is far superior to that achieved in a fluidized bed.

Jan 1, 1996

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996

By R. A. Hodge, J. W. Murray

By an order of the Executive Council of the Provincial Government dated January 18, 1979, a Royal Commission was established under the Public Inquiries Act to: 1) Examine the adequacy of existing Federal and Provincial requirements for the protection of the health and safety of workers associated with exploration, mining and milling of uranium in B.C. and for the protection of the environment and of the public. 2) Receive public input on these matters. 3) Make recommendations for setting and maintaining standards for worker and public safety and for the protection of the environment as a result of the exploration for the mining and milling of uranium ores. At that time,and at the present time in British Columbia, no uranium mines were, or are, in operation. Exploration at a number of sites was under way and one deposit, the Blizzard deposit, with estimated reserves of 1.92 million tonnes containing approximately 4.74 million kilograms of U308 was at an advanced stage of exploration. With our Terms of Reference, and because of the diverse geology of the western Cordillera which could potentially host a broad variety of uranium, deposit types, the Commission was faced with the task of considering environmental and health protection necessary for the potential development of [any] kind of uranium mineralogy situated in [any] of the environments found in British Columbia. Over the past 17 months since that time, much has transpired, culminating in the February 27, 1980 Provincial Government announcement of a seven year moratorium on exploration, mining and processing of uranium coupled with the termination of our Inquiry before completion of the hearings. The Government sebsequently modified its decision to terminate the Commission completely, deciding instead to stop the hearing but allow time for the Commission to gather in the work that had been initiated

Jan 1, 1980

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By Subhash B. Bhagwat

No economic activity would take place without human ingenuity, driven by our needs and wants. Economic activity is made possible by the energy from fossil and other energy sources, our technological hardware, the buildings and infrastructure made from materials such as metals, plastics, wood, water, and numerous industrial minerals. Industrial minerals are difficult to define; however, they generally include utilitarian minerals other than metals and fuels. Some of the industrial minerals form an exception to this categorization and, as explained elsewhere in this book, belong to more than one category because of the manner in which they are used. Industrial minerals are so numerous, and their applications so ubiquitous that they often do not receive the attention given to metals or fuels. Nevertheless, without industrial minerals, many of our most fundamental economic activities such as construction of our cities and towns, control of floods, transportation of our people, the search for minerals, the smelting of metals, and the delivery of supplies of clean water would be impossible. How then do we assess the economic importance of such a variety of materials lumped together under the general designation of industrial minerals? The price per ton or the total amount consumed do not satisfactorily explain the relative value of these materials to the economy. For example, the current price of limestone is about $5/t and the price of fluorspar is about $190/t. However, nearly 1.1 Gt of limestone, valued at about $5.5 billion, are consumed in the United States annually, compared with 590 kt of fluorspar, valued at about $1 12 million. It would not, however, be accurate to conclude that the mineral with the higher total value is always more economically important. Many other questions must be answered before making judgments of this type. These questions include how many people are employed in the production, processing, and distribution of the mineral? How is the mineral used? Is it partly or entirely imported? Where do the imports come from? How is the mineral transported? Is the mineral considered critical to national security? Is there a substitute material available in case the mineral supply is interrupted? Where would the substitute be produced? What would be the basic material from which the substitute will be produced? Even when these questions have been answered satisfactorily, the economic importance of the mineral is not completely known until the consuming sectors are studied as well. For example, even though the manufacture of fighter aircraft is vital to the national security, it employs only a fraction of the number of people employed in the housing and construction industry or the automobile industry or the appliance industry. Mineral commodities consumed in these latter sectors of the economy are more significant than those consumed in the production of fighter aircraft, because nearly two-thirds of the Gross Domestic Product (GDP) depends on the purchasing power of individual consumers. In comparison, the entire defense budget accounts for only 6% of the GDP. There is no easy way to present the importance of industrial minerals to the US economy because most minerals have diverse applications and products made from industrial minerals often con- tribute to the production of other goods and services. One way of highlighting the value of a mineral would be to relate it to the GDP reported by categories such as construction, machinery, stone, clay and glass products, electrical and electronic equipment, paper and allied products, and chemicals and allied products. These GDP categories represent industries fundamental to the economy totaling $644 billion, or about 12% of the GDP in 1990. However, these categories are not convenient for discussion of the many minerals that are used in our complex economy. In a general way, minerals are the 5% of our economy that make the other 95% possible. This chapter, therefore, discusses a selected few industrial minerals to illustrate their importance to various sectors of the economy.

Jan 1, 1994

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By Boris V. Vlasenko, Vadim P. Potapov, Gennady I. Gritsko

In this paper we consider the elements of an information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated sys tem is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of changes in geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By H. Sevim

A new method of designing haulage systems, consisting of belt conveyors and hoists for underground mines is discussed in this paper. Efficient and economic design of such systems will prevent operational bottlenecks and provide savings. The developed model uses a heuristic algorithm to optimize the design parameters and to select the proper equipment specifications. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate belt conveyor networks of any configuration and hoisting systems that can be either drum or friction hoists for single or multiple-level operations. The model also has the option to internally determine the required capacities of the bunker(s) and shaft- bottom bin. The objective of the optimization process is to minimize the "expected cost per ton of ore hauled" from the working faces to the surface. A numerical example is included to illustrate the capabilities of the model.

Jan 1, 1987

By Ulf Marklund, Stig Markstrom

Pioneering work with pilot scale autogenous grinding started in Boliden 1956. From 1961 to 1991 eleven fully autogenous grinding (AG) circuits have been installed at various concentrators within the Boliden company. A compact two-stage grinding system was de- signed in the beginning of 1970s. The system included a pebble extractor which feed the secondary grinding stage with grinding media. The APC grinding system (Autogenous/Pebble/Crusher) is a further development of the AG concept. A new design of the Boliden pebble extractor together with improved control strategy make the performance of the APC system suitable to almost any ore quality. The Boliden AG concept is probably the most cost efficient grinding system of today.

Jan 1, 1998

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By John E. Butler

Due to the present economic climate, particularly the depressed copper market, conventional mining, milling and flotation operations have been suspended. However, due to the apparent amenability of the ore to &apos;natural&apos; leaching, investigations have been initiated into establishing an in-situ leaching operation as a preferred alternative to conventional operations. Cement copper production has been developed in parallel with the leaching trials and is presently at the rate of approximately 3,000 tonnes of contained copper per annum. Testwork includes controlled leaching of ore both in the laboratory and in-situ following blasting.

Jan 1, 1981

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study has been conducted to remove iron from sulfate solutions using Eichrom&apos;s Dipexo® extractant, P,P&apos;-di(2ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy&apos;s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003