Search Documents

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Thomas Bubanovich

Engineers at the Freeman United Coal Min¬ing Company, located in West Frankfort, Illinois, have been using a computerized production planning and maintenance reporting system, which have been designed exclusively for underground coal mining. This paper will explain a dynamic graphical simulation and computerized time study system that has been used to design and evaluate underground production systems for optimizing productivity. Also with the aid of customized software, detailed records on changeable components of underground equipment, including the vendor's name, date installed, operating and maintenance hours, etc., have helped Management to select the best available components for their equipment. The MPASS System, Mine Performance Analysis Simulation System, developed through a cooperative agreement with Freeman United, Ketron Inc., and the U. S. Department of Energy utilizes new methods to analyze and design production systems in underground coal mines. The MPASS System is a menu-driven user oriented system of interactive computer programs, which form five major subsystems. The subsystems: 1. Simulation 2. Time Study 3. Mine Background Reports 4. File Maintenance Subsystem 5. Statistical Analysis Subsystem

Jan 1, 1987

By R. M. Hays

Jan 1, 1980

By JÖRG DEHNERT, PETER WINDISCH, Bernd Schönherrt, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposures of miners in Germany, especially during remediation work in old mines. The QESS is a light-weight, modular, and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil, and expanding foam. It is designed to seal off radon-rich parts of galleries within only a few minutes. Originally, the QESS was developed to protect miners against radon exposures. Then, the QESS found the attention of several mine rescue teams at a German mining conference. The Student Mine Rescue of the Technical University Bergakademie Freiberg and the Wismut Mine Rescue carried out firstmine rescue drills in Freiberg and Schlema. Additionally, a mine rescue drill was carried out by the Front Range Mine Rescue in the Edgar Experimental Mine of the Colorado School of Mines. These drills helped to improve the systemand highlighted its potential for mine rescue operations. Now, the QESS is wellsuited for small-scale mining. The QESS can be used to seal off galleries in only a few minutes to both protect miners fromradon exposures and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

Jul 23, 2020

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By R. Patterson

Tracer gas sampling methods are useful for monitoring ventilation systems, especially in remote or inaccessible areas, and can be utilized for analysis of the ventilation system immediately following a mine emergency. However, the success of this technique is largely dependent on the accuracy of release and sampling methods. Analysis of sampling methods is crucial for rapid response and dependable results during emergencies. For the purpose of this study, four well-accepted sampling techniques currently used in the mining industry were compared using solid-phase microextraction (SPMe) fibers with sulfur hexafluoride (SF6), an industry standard, as the tracer gas. Current sample collection techniques include plastic syringes, glass syringes, Tedlar bags and vacutainers. SPMe fibers are used in a variety of industries, from forensics to environmental sampling, and are a solventless method of sampling analytes. To analyze these sampling methods, samples were taken from a 0.01 % standard mixture of SF6 and nitrogen and analyzed using electron capture gas chromatography. A relative standard error of less than 10% validated results to compare the accuracy of various methods. The technical and practical issues surrounding each sampling method were also observed and discussed.

Jan 1, 2011

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974