Search Documents

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By Ralph P. Hackl

Biooxidation processes for treating arsenical and other types of refractory gold ores are touted by many as being simple, inexpensive and environmentally friendly. One of the advantages claimed by proponents of biooxidation is that arsenic is disposed of as insoluble ferric arsenate which is suitable for long term disposal in tailings ponds. However, there is considerable controversy as to the stability of ferric arsenate with respect to re-dissolution of arsenic. In particular, there is concern that the amorphous ferric arsenate produced at low temperature is not stable, especially at the alkaline pH's required for cyanidation. There is a general lack of published information on the stability of arsenical bioleach tailings. Past work on ferric arsenate stability has usually involved purely chemical systems and the use of synthetically prepared precipitates. Upon completing the Salmita bioleach pilot plant campaign (Hackl and Wright, 1989) the author had the opportunity to test the stability of the arsenical bioleach/cyanide tailings which were produced. This paper summarizes the results of that work.

Jan 1, 1990

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By Kim Appleby

Epithermal gold-silver (lead-zinc-copper-manganese) mineralization on Misima Island is confined to steep and reactivated flat-lying normal faults in the upper plate of a major, shallowly dipping detachment fault. The hangingwall comprises an Eocene metavolcano-sedimentary sequence that has been extensively intruded byMiocene calc-alkaline granodiorite. It is unconformably overlain by Pliocene sedimentary and volcanic rocks. High-pressure amphibolite facies rocks dominate the footwall and have many characteristics of a metamorphic core complex. Mafic-alkalic lamprophyre dike swarms intrude the hangingwall and footwall sequences. Previous workers attributed the gold-silver mineralization on Misima to the intrusion of the porphyritic granodiorite (Williamson, 1984). This has been proposed for many tertiary gold deposits of the southwest Pacific(Sillitoe, 1989; Leach and Corbett, 1994).

Jan 1, 1996

By Robert M. Rowe

Among the increasing operating costs affecting today' s processing facilities are those necessary in meeting the continually growing requirement for safe and environmentally sound materials- control and handling procedures. Of particular interest are materials listed as hazardous, the need to maintain accurate records of their acquisition, consumption and disposal, and the obligation to employees and the community to have information available regarding such materials. Some requirements affecting modern operating facilities are reviewed in this paper, and potential methods for dealing with complex handling and documentation requirements, including computer automation, are discussed.

Jan 1, 1991

By Pierre J. Wauters, Eddy J. Jacques

Starting up a fan or modifying its setting point either by rotational speed variations or blade angle changes, obviously results in new ventilation conditions in the network, which is, of course, the object of the operation. However, since transient phenomena may then occur, particularly in complex networks, there may be a need to simulate these situations prior to any action. This is all the more true, if we are dealing with a multiple interactive fan sys- tem. Simulations with a transient model have shown that the flow in certain airways could be temporarily reversed due to the pres- sure variations that reach both its ends with a different time lag. This phenomenon may cause dangerous situations to occur in cases of fire or outburst of methane. It is also true that the air flow could be reversed in secondary and less powerful fans, while still rotating in the normal direction. The study and the experimental investigation of the extension of the reverse flow characteristic is therefore justified from two points of view : • a numerical simulation model for transient flow conditions must be capable of handling temporary reversed flows, and thus have appropriate fan characteristic curves available over the entire operating domain; • while operating fans, reversed flows should be avoided or at least reduced. Therefore, the design of start-up procedures or real time control algorithms should take these phenomena into account. A particular interesting application is the operating of two fans in parallel. In order to investigate experimentally the characteristic curves of a fan under reversed flow conditions a small scale model was built. This facility was designed in such a manner that it was possible to carry out experiments concerning flow reversions and to try out sequential start-up procedures for two fans in parallel.

Jan 1, 1997

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By Takaji Kusakawa

In Japan, almost no natural gypsum is mined for industrial uses of gypsum, and almost all gypsum is synthetic gypsum, that is desulphogypsum, produced by waste sulphur dioxide gas from metal smelters and power plants, and other industrial waste sources. The amount of such sythetic gypsum production has reached more than six million metric tons per year (1979). Major uses are for cements and building materials. Other uses are soil conditioner, investment casting mold, organic composite materials, etc and sulphur recovery by gypsum decomposition is being examined. This paper summarizes present Japanese production and uses of sythetic gypsun produced from industrial waste.

Jan 1, 1982

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By J. Lovering, H. Wilhelm, P. Siewert

Introduction The Afton property is located 290 km (180 miles) by air east-northeast from Vancouver and 14 km (8.7 miles) west of Kamloops, a city of 60,000 people, in south central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 670 m (2198 ft) above sea level. The ore body is a porphyry copper deposit that has undergone supergene alteration. The major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is 1% with an overall copper distribution - 70% native, 25% chalcocite, and 5% chalcopyrite with bornite and covellite. The ore also contains important but variable amounts of gold and silver. The mill was designed to treat 6350 t/d (7000 stpd). Semiautogenous grinding was selected to minimize capital cost and because of the expected high clay content of the ore, which would have caused problems in a conventional crushing and screening plant. Test work indicated that a recovery of 87% was possible in a circuit incorporating both flotation and gravity separation. Flowsheet Run-of-mine ore is crushed in a 1.06 x 1.65-m (3.5 x 5.4-ft) Allis Chalmers gyratory crusher set at 228.6 mm (9 in.), closed side setting. The surge pocket, below the crusher, is emptied by a Hydrastroke feeder onto number one conveyor, which discharges onto a 180,000-t (198,416-st) coarse ore stockpile. Six Hydrastroke feeders on two conveyors withdraw the crushed material from the bottom of the pile. These two conveyors, in turn, discharge onto the belt feeding the semiautogenous mill. The live storage in the stockpile is approximately 22,000 t (24,250 st), sufficient for three days' mill feed. Primary grinding is accomplished in an 8.5-m (28-ft) diam by 3.7-m (12-ft) long Koppers (Hardinge Cascade) mill (Fig. 1) containing a 10% ball charge and driven by a 4000-kW dc variable speed motor. The mill dis¬charge is pumped by a 10 x 12 G.I.W. pump to a 1.22 x 4.88-m (4 x 16-ft) stationary screen sloped at 20°. Screen oversize returns to the semiautogenous mill (SAM), and the undersize flows by gravity to the ball mill discharge pump box. Secondary grinding is performed in a 5-m (16.4-ft) diam by 8.84-m (29-ft) Koppers overflow ball mill driven by a 3430-kW synchronous motor through an air clutch. The mill is in closed circuit with a Krebs Cyclopac containing 10 635-mm (25-in.) cyclones and the cyclone overflow, at 35% solids and 65% to 70% -200 mesh, is flotation feed. In order to limit the buildup of native copper, circulating in the secondary grinding circuit, a portion of the underflow from the cyclones is processed in a circuit containing screens, cyclones, and shaking tables to produce a finished metallic copper concentrate. Primary mill variable speed drive The overall waste to ore ratio at Afton was 4.5:1. The mining was to be done with only three shovels, which meant that it was highly unlikely that more than one of them would be in ore at any one time. The resulting inability to blend the mill feed made it impossible to prevent wide swings in the grade and grindability. The variable speed do drive motor installed on the semiautogenous mill was selected because of the extreme variability of the Afton ore body. This variability has persisted throughout the lifetime of the mine. There are times, however, when due to ore conditions, the mill is operated at full speed (78% of critical) for extended periods of several shifts duration. There are other times when the mill speed may be changed several times in a 12-hour shift due to changing ore conditions. When ore is processed that contains a fairly large proportion of fine native copper, the primary mill speed and, consequently, the tonnage may be reduced to improve the secondary grind and to maintain an acceptable grind and recovery. High clay ores require less mill speed and more dilute grinding densities. In the latter case, the slower primary mill speed also helps to minimize damage to the mill liners. Approximately 57% of the time the mill operates between 90% and 100% of full speed or between 71% and 78% of critical. The variable speed is also used for inching during mill relines.

Jan 1, 1987

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By A. Wahab Khair, Negendra P. Reddy

INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982). One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Elorgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cy to toxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le ?oux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly . Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles , of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield,

Jan 1, 1986

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

By Robert S. Hendricks

The paper describes the design and operation of a Shaft Boring Machine (SBM). The machine has been developed by The Robbins Company. It is anticipated that the prototype, which will bore shafts in the 6.1 to 7.3 m (20 to 24 ft) size range, will be placed in operation during 1985. This pioneering application of rapid excavation technology is expected to lead to significant improvements in the cost and speed of shaft construction. The technical and economic factors which have limited the employment of Shaft Drilling and which caused unsatisfactory results with earlier attempts at Shaft Boring are reviewed. The design criteria adapted to overcome these problems are discussed. Cost and performance estimates are presented and are compared to conventional sinking methods. Factors that influence the application of the SBM to specific projects are reviewed.

Jan 1, 1985

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By Dao De Xu, Heechan Cho, Mark S. Klima

A study was conducted to determine the feasibility of using dense-medium centrifugation for separating fine (-150 µm) coal. A centrifuge provides the capability of varying the rotational speed and retention time independently, which offers the potential for a higher degree of control as compared to a dense-medium cyclone. Tests were conducted with a 140-mm diameter by 76-mm long Plexiglas separator, which was fitted with appropriate feed and discharge pipes to allow continuous separations to be made. A suspension of ultrafine (-10 µm) magnetite and water was used as the dense medium. The effects of operating conditions, including the magnitude of the 'g"-force and retention time, on centrifuge performance were investigated.

Jan 1, 1995