Search Documents

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By R. Spring

Artificial intelligence, and especially expert systems, are currently receiving considerable attention. Of interest to the control engineer is the utilization of these tools for real-time process control applications. To evaluate this technology, a real-time expert control system was implemented in one of the grinding circuits at Brenda Mines Ltd. The performance of this micro computer based expert system compared satisfactorily to the proven supervisory control system currently in use. The study confirmed the expectations that expert systems have potential for real-time, supervisory control of mineral processing operations.

Jan 1, 1989

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014

By H. Polat, S. Chander

Relatively large amounts of hydrocarbons such as fuel oils are often needed in the flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promoters. The reagents that are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Because the physical and chemical variables influence various subprocesses in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of the clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promoters. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1999

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By Ernest H. Gilmour

Introduction An earth science teacher at the junior high school level has the potential of working with 450 students per year. And these young people are at an age where they can be properly informed about the importance and necessity of a viable, domestic minerals industry. It was with this philosophy that a course was developed at Eastern Washington University for science teachers entitled, "The Minerals Industry of the Pacific Northwest." The two-week course is sponsored by the Northwest Mining Association and the Idaho Mining Association. It was first taught during the summer of 1971 and will be taught during the summer of 1986 for the sixteenth straight year. It is a two-week mini-version of the very successful six-week course taught at the Colorado School of Mines. In 1971, Russ Chadwick was President of the Northwest Mining Association. He suggested that such a course should be developed and offered at Eastern. It was determined that tuition scholarships would be necessary. This would ensure that a reasonable number of teachers would register for the course. Say a teacher has five classes a day, with 30 students in each class. Some 150 students come into contact with that teacher each term. With three terms a year, an instructor works with about 450 students per year. So, with 20 teachers in the course, it was possible that 9000 students a year could learn from our informed teachers. And now, after 15 years, more than one million students have learned about the minerals industry from teachers who have completed the course. The course is designed to take the teachers through all aspects of the minerals industry. Most of the lectures are given by the working geologists and engineers who talk about their jobs in the industry. This is extremely important for the credibility of the course. The teachers realize that the lecturing professionals really believe in what they profess. Industry fundamentals The course begins with a lecture on the need for minerals in a modern society. Most of the teachers do not realize how critical minerals are to every aspect of our daily lives. The lecture is followed by the US Bureau of Mines movie, "Minerals Challenge." An exploration geologist then discusses what is involved in the exploration for a mineral deposit. This includes a case history that the geologist has actually been involved in

Jan 9, 1985

By N. Champigny

The geostatistical estimation of the reserves of an ore deposit is highly dependent on the quality and stability of the variograms of the sample grades. Gold deposits commonly show a skewed grade distribution. The few high grades at the tail end of the distribution produce unstable variograms that are difficult to model. If these grades are cut to a lower grade value or removed, more stable variograms are obtained. However, outlier grades may make a deposit economically viable, and their cutting or removal should be treated with caution. To reduce (but not to eliminate) the effect of high grades, a transformation of the raw data can be performed. Most commonly used transformations are: logarithm, gaussian anamorphosis, rank and indicator. Variograms of the transformed grades are resistant to high grades and present a clear structure. The weak point of data transformation appears when grades are estimated by kriging; the estimates are very sensitive to slight variations in the parameters of the back-transformation. More robust variogram estimation procedures can also be used, but often these procedures are not suitable for skewed grade distributions as they are based on an assumption of a contaminated normal distribution. The Porgera gold deposit in Papua New Guinea has a highly skewed grade distribution, with grades ranging from 0.01 to 3500 g/t and a coefficient of variation greater than 5. For the geostatistical estimation of the high grade zone of the deposit, the influence of the high grades was quantified by calculating and comparing the following variograms: raw grades, raw grades with the highest grades removed and transformed grades. The study confirmed that there is no general method for handling high grades in a geostatistical reserve study. Several methods should be tried to quantify the influence of high grades.

Jan 1, 1991

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By M. R. Bowie, J. M. Barker, J. S. Hingtgen

Techniques of testing perlite require a combination of art and science. The modifications made to the perlite Corp. vertical laboratory furnace include addition of instrumentation, flowmeters, vibrators, automatic feeders, and regulators. The basic testing sequence consists of expanded density, furnace yield, compacted density, percent sinkers, and compaction resistance. These tests are modified versions of those specified by the Perlite Institute. This sequence is designed as a preliminary evaluation of a material's suitability for horticultural-aggregate end uses rather than a detailed measure of filtration capability.

Jan 1, 1988

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By Ronald S. Tanaka

In the planning stages for a dozen years, the 9.11 mile long Mount Macdonald Tunnel is the focal point of the $600 million dollar Rogers Pass Project. The paper will discuss the construction of the tunnel that is being carried out from both ends. The eastern portion contractor has used a tunnel boring machine to excavate the upper part of the tunnel and at the west end contractor selected the conventional drill and blast method. A ventilation shaft located near the mid point is the main part of a ventilation system unique in the Western Hemisphere.

Jan 1, 1987

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

Controlled-blasting experiments in small development drifts were conducted at CANMET's Experimental Mine in 1992 and 1993. The objective of these experiments was to develop suitable controlled-blasting techniques for small development headings that are drilled by jackleg with 32-mm-diam holes. The experimentation was also aimed at providing insight into blast-damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rock-mass structural data. The drift faces were approximately 2.4 by 2.4 m (7.9 x 7.9 ft) in size with 36 to 43 holes drilled to a depth of 2.4 m (7.9 ft). Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO was used as the main explosive and decoupled 19-mm (0.75 in.) diam semigelatin dynamite charges were used in the perimeter holes. Smooth-blasting techniques and presplitting were tested in the underground mine. All of the blasts were monitored with a multichannel blast-vibration monitor, to which was attached sets of high frequency geophones and accelerometers. These experiments demonstrated the efficiency of controlled-blasting techniques for the reduction of blast damage and also demonstrated the need to improve the safety and efficiency of using explosives.

Jan 1, 1997

By David A. Gulley, William A. Vogely

INTRODUCTION The Scope of the Chapter This chapter discusses environmental regulation and closely-related public policies associated with mineral development in the United States. This chapter outlines the nature, extent, and amelioration of secondary effects of mineral development. It sketches the policy foundations of regulation; discusses the implementation of environmental law; describes land use conflicts and land management regimes; and surveys the costs and benefits of environmental regulation. Since regulations are subject to frequent change, the chapter emphasizes basic factual and conceptual material, rather than specific regulations. The goal is to familiarize the reader with the general nature of environmental impacts and mitigation which arise in the minerals industry, and with the issues surrounding the regulation debate. The chapter is organized as a series of sub- chapters. The first of these is a discussion of the conceptual foundations of regulatory policy. The second section summarizes the principal federal environmental statutes, and the implementation of such regulation. Following that, the third section summarizes the current state of knowledge regarding the types of environmental impacts associated with mineral development. This discussion, organized in a format similar to that used in environmental impact statements, can be thought of as a guide to reading and understanding such statements. Next, the fourth section surveys studies of the costs and benefits of environmental regulation. 'These empirical studies are evaluated in terms of the framework developed in the first section of the chapter. In the fifth section, the discussion turns to federal, state, and local approaches to land use control and siting, and the economic analysis of such conflicts. Included are discussions of the two principal forms of public lands mineral entry, the 1872 location patent system and the 1920 leasing approach. CONCEPTUAL FOUNDATIONS OF REGULATORY POLICY David A. Gulley The Role of Regulation in a Market Economy What is Regulation?: Regulation is the intervention of government in the activities of the private market. In a market society, the private sector is presumed to be the most appropriate economic agent. Given this presumption, regulation generally begins with a demonstration of persistent problems under laissez-faire in a given context. Environmental and related regulation occurs because the public believes the free market does not properly value environ- mental quality. In this section, concepts are advanced to aid the reader in understanding the government's role in this respect.

Jan 1, 1985

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995

By Mark W. Johns

The design or optimization of a carbon-in-pulp (CIP) plant requires the determination and setting of a number of parameters to ensure optimum economic performance. A number of these parameters are either fixed, a function of the pulp, interdepen­dent, affect other parameters or outputs, so only a limited number of degrees of freedom exist from a metallurgical point of view. The traditional CIP contactor employs a low carbon concen­tration, a low agitation intensity and a reasonably long pulp residence time. The pump cell contactor employs a high carbon concentration, a high agitation intensity and a reasonably short pulp residence time. The two philosophies are dipolar in nature and the question arises as to which configuration is the optimum configuration for a CIP plant. The carbon particle size is shown to have a small effect on the capital cost of a CIP plant. A decrease in the pulp residence time, an increase in the pulp density, an increase in the carbon residence time, an increase in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the capital cost of a CIP plant. The pulp residence time, the pulp density and carbon particle size are shown to have a small effect on the operating cost of a CIP plant. An increase in the carbon residence time, a decrease in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the operating cost of a CIP plant. The optimum CIP plant, therefore, employs a short pulp residence time, the traditional pulp density, a long carbon residence time, the traditional carbon particle size, the traditional agitation intensity, and the traditional number of stages. Neither the pump cell configuration nor the traditional CIP configurations match the optimum configuration.

Jan 1, 1995

By F. D. Fox

Abandoned mill tailings deposits can be found scattered throughout the Northern Black Hills of South Dakota, indicative of past mining activities that originated during the great gold [ERRATA SHEET RESTORATION OF GOLD MILL TAILINGS, BLACK HILL, SOUTH DAKOTA 84-119 F. D. Fox Under subtitle Prospects Related to Present and Future Tailings Disposal Practices, include reference No. 12 in paragraph seven after "construction of the Grizzly Gulch tailings disposal project,"12 Reference 12 should read: Jeffries, Lawrence F. and Tczap, Andrew, "Homestake's Grizzly Gulch Tailings Disposal Project," paper presented at 1978 International Mining Show, October 11, 1978.]

Jan 1, 1984

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986