Search Documents

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By Bob Katsiouleris

Having passed through the worst of times for industrial minerals demand, there are signs that the best of times lie ahead. If the downturn was the result of unsustainable economic policy, the path forward has everything to do with sustain-ably meeting the demands of more people enjoying higher standards of living than ever before. Minerals producers must be poised to understand and meet their requirements well into the next decade. Successfully marketing industrial minerals - the building blocks of a growing and increasingly urban world population - will depend on producers? ability to respond nimbly to a rapidly changing and regionally evolving macroeconomic environment. A renewed focus on energy conservation, sustainable agriculture and building practices and consumer demand for products with a smaller environmental footprint will drive product and market segmentation strategies. These trends will not only shape the way industrial minerals producers do business, but also the type of skills and people they will require to run those businesses.

Jan 1, 2011

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By John E. Good

A new coal boom is under way in western Canada. As recently as the mid-1960's, the coal industry in western Canada was considered stagnant and, by some people, dying. But Japan's growing need for coking coal, which became more pronounced in 1966, sparked great interest in western Canadian reserves.' As a result of a rapidly expanding export market and growth in domestic demand, Canadian coal production spurted to 16.6 million tons in 1970. Production in 1965 was 11.5 million tons. Today, about 60 percent of Canada's output comes from western Canada, but by 1975, 87 percent (23.1 million tons) is expected to come from this area, and 96 percent (68.3 million tons) by 1990. Opening, developing and operating new coal mines to meet the needs of a rapidly expanding market for western Canadian metallurgical coals pose some unique and difficult problems. Covering nearly every aspect of opening properties in remote areas, the problems are met in exploration, transportation, construction, mine operations, coal preparation, manpower and ecology. Paul Weir Company has been involved as coal consultants on various projects in western Canada for some years. In presenting this paper, we make no attempt to present an in-depth or detailed analysis of any one specific situation. Each has, or would have, its own peculiarities or characteristics, both physical and economic. Instead, the objective is to provide for those not intimately

Jan 1, 1972

By Antonio Tafra, Rene Dominguez, James Spenceley, Brady Hays

"Extracting one of the world’s most valuable natural resources — copper — hinges on the availability of the world’s most essential resource: fresh water. But try sourcing fresh water in one of the driest places on Earth, Chile’s Atacama Desert.BHP, majority owner of the Escondida copper mine in Chile’s Antofagasta region and Minera Escondida Limitada (MEL), operator of the mine, were looking for sustainable solutions to deliver desalinated water to the mine, while protecting the environment and complying with the local water authorityregulations.The mining giant chose Black & Veatch to solve this challenge.Solving a global miningchallengeMines use large quantities of water for mineral processing and metal recovery. Water supply, and not mineral ore, is often the major constraint to mining production and development of projects, especially in Chile. Mining operations must have a reliable water source that complies with local regulations, without adversely impacting the environment or affecting the water supply of nearby communities.Worldwide, mining companies and their owners, shareholders and regulators are placing new levels of focus on minimizing the impact of mines on the surrounding landscape and communities. Balancing the economic benefits and needs of mining operations with the potential freshwater impacts requires mines to pay serious heed to the environmental and social issues related to water. Today, mining companies are being proactive and are taking action to protect precious freshwater resources while seeking opportunities to reduce and mitigate their water impact.Delivering a desalination solutionBHP and MEL needed an efficient, technologically advanced seawater desalination plant, along with a conveyance system and infrastructure that would carry desalinated water more than 180 km (112 miles) from the ocean to the mine. Four pumping stations convey the water to a reservoir at the mine site, which is 3,200 m (10,500 ft) above sea level."

Jan 6, 2018

By Gary H. Higgins

The paper by Lewis and Braun l presents experimental and calculational evidence that primary chalcopyrite ores are rapidly oxidized by warm oxygen-bearing water. Resulting solutions contained copper sulfate products of the matrix rock decomposition such as magnesium sulfate and sulphuric acid. Iron was oxidized to insoluble hematite and hydrous iron sulfates. Oxygen injection near the base of a broken and permeable flooded ore deposit was calculated to cause circulation of oxidizing solutions to the entire permeable region. The rate of dissolution of copper and degree of oxygen saturation for given oxygen injection rates were presented. Their work suggests that in-situ recovery of deep, disseminate primary copper deposits is technically feasible. The actual feasibility depends on economics and environmental safety as well, and it is the purpose of this paper to address these two aspects.

Jan 1, 1972

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By G. Plenge, M. Brittan

"Plant design parameters for gold extraction, leach residence time and cyanide consumption are generally determined from standard bench-scale bottle roll or agitation leach tests. The application of laboratory data to process design has essentially evolved from the testing of oxide or low cyanide-consuming ores. Such scale-up factors may not be appropriate for ores that deplete cyanide and oxygen since this interferes with gold extraction kinetics. High cyanide-consuming ores also exacerbate the differences between the conditions applicable to small batch tests and large continuous operations. Testing a reactive high-sulfide South American ore deposit necessitated the re-evaluation of conventional bench-scale cyanidation procedures. Pulp density can be a major factor affecting the results for plant design purposes and should be treated as a test work variable. As with high clay-bearing ore, where pulp viscosity can hinder mass transfer, minimizing the influence of test equipment on gold extraction kinetics may require low pulp densities. This introduces interpretative complexity since cyanide consumption changes as a function of pulp density. Activated carbon also consumes cyanide, so its effect has to be accounted for in the case of carbon-in-leach (CIL) or carbon-in-pulp (CIP) plant flowsheets. Since cyanide is an expensive reagent, often a major component of plant operating costs, it is important that the scale-up of cyanide consumption from laboratory to plant be representative. The traditional method of reporting cyanide consumption in bench-scale testing is questioned since it takes credit for residual free cyanide in leach tails. The projected plant consumption may be better estimated by using the total cyanide addition in a laboratory test. We propose a test work protocol that categorizes the cyanide consumption into its components but requires more extensive testing to generate design data. The ultimate validation of scale-up factors used by project engineers requires rigorous bench-scale versus commercial plant comparative data. Such data are not readily available.IntroductionMajor factors in the design of a gold processing plant are gold recovery, leach residence time and cyanide consumption. These parameters are important determinants of project revenue and costs and, thereby, potentially of project financial viability. Estimates of the associated design criteria for a commercial plant are normally generated from laboratory cyanidation, carbon-in-leach (CIL) or carbon-in-pulp (CIP) tests using standard procedures (Angove, 2005). The key question is whether the standard laboratory test work procedures developed historically for low reagent consuming ores are appropriate for ores that are highcyanide and oxygen consumers.The present paper examines test procedural factors that can influence the test work results and, therefore, their interpretation for design scale-up purposes. The study refers in particular to a high cyanide-consuming sulfide ore. The ore was being tested to develop scoping level engineering design criteria for a proposed project in South America."

Jan 1, 2015

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia's underground coal mining industry has reported few new cases of pneumoconiosis for more than 20 years. Mortality from coal workers' pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in X-ray surveillance programs are also lower in Australia. The U.S. National Institute for Occupational Safety and Health (NIOSH) was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among U.S. coal miners. A number of factors, including coal dust exposure, silica exposure and coal rank were examined as potential contributors to the above noted differences. Comparison of coal rank data from each country did not illuminate the issue. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. If quartz is contributing to the greater number of cases of pneumoconiosis in the United States, more effective dust control measures, as well as an independent exposure standard for respirable quartz in coal mining, should be implemented to reduce this potentially disabling condition.

Jan 1, 2012

By N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline?s long-term performances and availabilities, to develop preventive maintenance plans, and to make future projections about the machine?s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, PAGE 736 and MARION 7820, which have been operating in Tunçbilek open cast coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages as: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data; (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (20 yd3) is seemed to be more reliable and less likely to fail when compared with Marion 7820 (40 yd3). The operating hours without failure range from 41 to 51 hours with 50 percent reliability.

Jan 1, 2011

By LUKAS FAHLE, Andrew J. Petruska, JURGEN F. BRUNE, Gabriel Walton, Elizabeth A. Holley

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (Lidar) data quality for rapid, digital, and eventually autonomous mine-wide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS provides data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest while reducing SLAM drift error by up to 90%. In collaboration with an operating block cave mine, we confirm these capabilities in field tests on a mine-wide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing, and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate, and comprehensive geotechnical inspections.

Aug 16, 2022

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By R. A. Haney

The Mine Safety and Health Administration has developed a model to estimate diesel particulate (dp) exposures in underground mines. The estimate uses either in-mine measured dp concentrations or engine manufacturers' standardized emission data and through a series of calculations estimates full shift dp concentrations by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method to estimate diesel particulate levels and determine the impact of various diesel particulate controls on occupational exposure to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 1998

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016