Search Documents

By William A. Ribich, Hans A. Hug

INTRODUCTION Providing sufficient thrust, particularly in the proper manner, is one of the major problems of conventional hardrock drilling and tunneling machines. For instance, with tunnel boring machines, massive jacks, mechanisms, and structures are required to generate and transmit the forces to the cutting head. One pays for this massiveness both in terms of material (dollars per pound) and in the attendant difficulties of transporting and maneuvering such machinery. The effect of an efficient thrust generation method on system size is evident when one considers conventional shaft drilling equipment. Raise borers are small enough to be used underground, while conventional big hole drilling equipment requires large amounts of space, personnel, and support. Proper application of the force is another problem, even with smaller holes such as blastholes. While one can load most tricone blasthole bits to their limit with such drill rigs as the Bucyrus Erie 61R or the Gardner Denver 120D, transmitting very large forces through the relatively flexible mast and drill pipe leads to large vibrations, fatiguing of the mast structure, and impact loads on the bit. In the following, a new method of generating the required rock fragmentation force is presented. Furthermore, the force is generated and applied in such a fashion that not only can the equipment size and weight be reduced, but also the cutter and equipment life can be increased.

Jan 1, 1974

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Wang Dianzuo, Luo Lin, Hu Yuehua, Qiu Guanzhou

This paper introduces a novel classification approach named the flotation classification approach which works by controlling interactions between particles. It differs considerably from the conventional classification processes operating on mechanical forces. In the present test, the micro-bubble flotation technology is grafted onto hydro-classification. Selective aggregation and dispersion of ultrafine particles are achieved through governing the interactions in the classification process. A series of laboratory classification tests for -44 pm kaolin have been conducted on a classification column. As a result, about 92 percent recovery for minus 2 pm size fraction Kaolin in the final product is obtained. In addition, two criteria for the classification are set up. Finally, a principle of classifying and controlling the interactions between particles is discussed in terms of surface thermodynamics and hydrodynamics.

Jan 1, 1995

By Drupad B. Desai

Baltimore Region Rapid Transit System project final design began in 1973. The Section A of the planned Phase I is scheduled to go into revenue service in late 1982. The subway line structures include earth tunnels, rock tunnels and cut-and-cover structures. Final designs were performed by both the DMJM/KE staff and by outside subconsultants. This paper deals with Section A of the program. (Fig. 1.) The overall program cost for Section A is estimated to be $721 million. The cost for construction and owner furnished equipment is estimated to be $600 million, including contingency and escalation to time of construction. The remaining amounts are for right-of-way, design, construction management and agency (MTA) costs. The Section A line structures, including station lengths, are divided as shown in Table 1. [ ]

Jan 1, 1979

By J. R. Diehl, R. W. Lai, R. W. Hammack, S. U. M. Khan

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of a selected coal pyrite and a mineral pyrite. Surface properties of pyrite were evaluated in terms of flotation response in the presence of both an anionic fluorosurfactant and sodium hydrosulfide. The charge transfer adsorption and oxidation potential of sodium hydrosulfide were evaluated using cyclic voltammetry. Drastic differences in the flotation response have been observed between the coal pyrite and the mineral pyrite. Significant differences in the cyclic voltammograms at pyrite surfaces of these two sources were also observed. Measurements by XPS and EGA were used to determine the oxidation products and the rate of oxidation of the coal-pyrite and the mineral-pyrite surfaces.

Jan 1, 1991

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By R. R. Beebe

When an economic mineral deposit is first discovered, it is almost immediately defined in terms of tonnage and grade. As exploration and assessment continue, the initial definition is ordinarily qualified by such terms as "proven," "probable" and so on. Even at this stage, the fundamental philosophies of the discoverers may manifest themselves in conservative or optimistic views of the deposit's potential. It is unusual, however, for the philosophies to be expressed in terms of metallurgical performance criteria at such an early stage unless the ore is very unusual in its chemistry or mineralogy. Even before drilling is completed, the first mining plans appear, with or without the benefit of metallurgical test data. This is the point at which management philosophies can have some of their greatest impacts. In ideal cases, where large, uniform ore bodies can be developed and mined according to assay cutoffs, the conventional philosophy of maximizing tonnage while minimizing cost can be followed without much metallurgical difficulty. Unfortunately, such cases are rather uncommon. Even large, low-grade

Jan 1, 1991

By Ron Jackson

The report gives a general method for the geological evaluation of a gold deposit. Recognizable parameters associated with gold mineralization are used to develop a model of an orebody. The California Mother Lode is used as an example.

Jan 1, 1987

By Dougal R. McCreath

The storage of energy in one form or another is a well established practice, demonstrated by the familiar sight of large oil storage steel tanks. Today, however, the problems of energy storage are taking on a new complexion. Increased emphasis on large and sometimes untried forms of energy storage is being generated by: (1) The uncertainties we face concerning future oil and gas supplies. (2) The growing need for the storage of peak-shaving energy on large utility systems. (3) The growing volume of highly toxic and energy generating wastes resulting from nuclear power plants. Concurrent with the growth of these pressures, legitimate environmental concerns now demand that the methods of storage which are utilized meet adequate criteria of safety and preservation of surface land, as well as fulfilling technical and economic functions. From these elements, increasing awareness has grown of the potential role that can be played by underground space in providing a storage medium for energy related materials. The vessels which must be built for underground energy storage will be built by the tunnel engineer, and the design requirements of such vessels will go far beyond the classical tunneling requirement to drive a stable, reasonably dry tunnel between two points. Depending on the nature of the material to be stored, the manner in which the storage is to be operated, and the specific risks to the environment which are involved, rock chambers must be designed as special purpose storage vessels. The tunnel engineer may be required to demonstrate that unusual pressure and temperature conditions can be sustained by the rock, or that containment of a toxic material can be assured. In certain cases there will be emphasis on

Jan 1, 1976

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By Mandira Madhuchhanda, N. B. Devi, P. C. Rath, R. K. Paramguru, K. Srinivasa Rao

An experimental investigation of the dissolution of three base-metal sulfide minerals, namely, CuFeS2, ZnS and PbS, in hydrochloric acid medium in the presence of manganese dioxide is reported. Polarization measurements and leaching studies were employed in the study. Dissolution occurred in the following three ways: by the cyclic action of the Fe3+/Fe2+ redox couple, by galvanic interaction between Mn02 and the sulfide minerals, and because of chlorine evolution from the system. The later two routes were found more effective at higher HCI levels. PbS appeared to be oxidized easily, whereas CuFeS2 was the most difficult to dissolve. ZnS dissolution fell in between PbS and CuFeS2.

Jan 1, 2002

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By D. Royston, D. Denlay

Pulp lifters are used to discharge ground pulp from non-overflow grinding mills. In straight-radial channel pulp lifters, discharge is often incomplete and back-flow down the pulp lifter can occur. Leading-curve channel pulp lifters can be used to ensure complete discharge, especially at high mill rotational speeds. The complex motion of solid materials in pulp lifters has been modelled mathematically for both straight-radial and curved pulp lifters in order to make comparisons between the two types. The model is supported by practical observations of the performance of curved pulp-lifters in a commercial 24ftSAG Mill as well as observations of the discharge from several commercial straight-radial pulp-lifter AG/SAG Mills.

Jan 1, 1999

Changes have been made in the Bulletin, Section I., for this month ; Personal and Employment columns have been added, and a Forum, in which will be included letters and discussions of general interest to members of the Institute ; live news and new matter have been inserted near the front; lists of officers and committees are placed next to the technical section, while standing matter and other information which is interesting chiefly when sought for, has been segregated as much as possible. Members are urged to co-operate with the Editor by sending in news items of themselves and others, and by giving some of their spare time to this department each month.

Jan 4, 1913

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By Matthew J. Hrebar

A comparison of hydraulic shovels (HS) versus front-end loaders (FEL) is commonly made when an excavator with some degree of mobility and medium reach is required. These applications are often found in hard rock open pit and surface coal mining applications, among others. The purpose of this paper is to present a comparative economic study of the two excavators. Production data was collected from both HS and FEL manufacturers as well as operating mines. Availability, operating costs, and estimated operating life were gathered from operating mines, while capital costs were obtained from manufacturers. The data was limited to studies and operations which included both types of mid-size excavators. The economic study is followed by a discussion of other factors considered by mine operators in excavator selection. The study was originally made for a presentation at the 23rd Intermountain Minerals Conference at Vail, CO.

Jan 1, 1992

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986

By Y. C. Kim

M.S. Azun The article unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that kriging (linear kriging) is superior to other methods such as polygon. This is not the case. The deterministic methods (referring to polygon, ID, IDS, etc.) should not be compared with the statistical methods (linear kriging, disjunctive kriging, etc.) because they differ not only in their assumptions, but also their tools used in estimation. Thus, they give different results. By comparing the results of deterministic methods and linear kriging, the authors conclude that polygon, IDS, and linear kriging give an average thickness close to the value obtained from realizations. Besides, they argue that linear kriging gives less variance than the others (Fig. 2). The first conclusion is expected, due to the well-known central limit theorem. The second is the result of the statistical properties of different estimators. Thus, the comparison presented in the paper is rather meaningless because the authors have failed to follow basic statistical procedures. The numerical results of different approaches to an estimation problem cannot be generalized. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous. Reply by E.Y. Baafi and Y.C. Kim The two key contentions made by M.S. Azun regarding the paper are: deterministic methods should not be compared with statistical methods and, hence, the results are erroneous; and the paper does not make a meaningful contribution. The first contention is an academic one. Most practitioners in ore reserve estimation could care less whether the tool they are using falls under a deterministic or a probabilistic method, so long as it gives the desired answers. It is probably for this reason that, whenever any new tool such as linear kriging is introduced to practioners in the mining industry, they would like to see a comparison test performed between the existing and the more familiar tools with a new and "strange" tool. Only when a new tool passes such a test, the generally conservative mining community would begin to utilize the new tool to its advantage. The second contention, is a subjective one. The final judgment should be left up to the readers within the mining community. If kriging is accepted more among practitioners, partly due to the paper, then the paper makes a practical contribution to the state-of-the art in ore reserve estimation. Finally, M.S. Azun entirely missed two main points in the paper. The first is that any comparative study of kriging vs. Polygonal or IDS should be performed for local estimation and not for global estimation. In the past, kriging was frequently compared with other existing tools in its performance on global estimation. Such results were nearly identical due to the central limit theorem effect, which further prevented the acceptance of kriging by practitioners. The second point is that a single case study using an existing property, as it was frequently performed in the past, is not sufficient because results depend not only on the tool itself, but also on the nature of the mineralization.

Jan 3, 1984