Search Documents

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By Peter McKenna

A mineral rights holding can ultimately only be turned to account by the profitable mining of ore on that property. The evaluation of South African gold mineral rights properties must therefore be carried out by assuming that they have potential to form part or all of a future gold mine. Such analysis involves the simulation of many of the estimation procedures that are normally carried out in a full feasibility study of a new mining venture but using far less data. This paper describes in detail the evaluation procedures that may be applied to an individual property and then indicates how these techniques can be applied to a whole mineral rights portfolio.

Jan 1, 1989

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982

By M. Kawulak

The necessity to protect the environment can limit mining activities and make some areas less attractive for the prospecting and exploration of mineral deposits. In Poland, the main environmental factors that restrain Irumng are: 1. Regional A Protection of the landscape B. Protection of ground water from contamination and depletion 2. Local A Conservation of fertile soils B. Conservation of forest resources C. Preservation of natural, cultural, and historical monuments The regional factors listed above that can limit mining are presented on a map of Poland. These data, combined with maps of known and potential mineral deposits, make it possible to delineate general levels of limitation for various mining-related activities varying from "no existing environmental limitations" to "no allowed industrial activity" As an example, a compilation of such data is presented for lignite exploration and mining in Poland. Lignite deposits occur within Upper Paleocene to Upper Miocene clastic strata at depths ranging from a few to 300 m. The thickness of the lignite is generally a few meters, but can locally reach over 100 m within grabens. As a result, the overburden-to-lignite thickness ratio varies from less than 1 to over 20. Within the same Tertiary strata, and within overlying Quaternary strata, several aquifers exist that produce good quality water that may be contaminated or depleted during lignite mining. The protection of these ground waters is the main factor limiting lignite mining and should be addressed in mining and environmental policy and planning.

Jan 1, 1996

By John D. Nelson, Clint L. Strachan

Drainage of tailings impoundments is a key issue for impoundment stability, water control, seepage control, and reclamation. Drainage control is an established operating practice where climate and site conditions permit, such as in South Africa and various mines in North America. In these areas, drainage control is primarily used to maximize tailings densities and to provide adequate impoundment stability. Drainage practices during operation also become an important issue when tailings impoundments are reclaimed. Time required for cover placement and post- reclamation seepage control depends greatly on the ability for tailings to drain and consolidate. This paper discusses drainage issues associated with gold tailings impoundments in terms of mechanics of saturated and unsaturated flow and experience with design and reclamation of tailings impoundments.

Jan 1, 1988

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By Takeshi Tanaka, Yasuhiro Komamura, Yuusaku Tominaga, Takayoshi Iwamoto

In order to assist better countermeasures for ventilation control in normal/abnormal condition of mine ventilation network in real time, branch relation table derived from a macroscopic characteristic of ventilation network is introduced in this study. The main results in this study are as follows; 1) One of macro characteristics of a ventilation network, as a relation between airflow rates in two branches chosen arbitrarily, is specified under the change of aerodynamic resistances in a branch. Airflow rate in a branch can be estimated by airflow rate in other branch changing aerodynamic resistance by using empirical formula. The empirical formula by computer simulation of the Horonai coal mine, Japan is considered to be a one-valued function with monotone or extremums. 2) A branch relation table shows the macro characteristics, mentioned above, of all the set of two-branch combinations in a network. Elements in the table give both information of control possibility range of airflow rate and total number of extremums in an empirical formula. 3) It is important that when aerodynamic resistance change in a branch is estimated by measuring airflow rates in two typical branches, the two branches should be chosen from branch combinations with monotonous relation in the branch relation table. 4) A flexible expert system to assist ventilation control in the specified branch in real time has been developed by using a branch relation table for a ventilation transfer diagram of the specified branch, such a coal face and an advancing face. A fuzzy reasoning is utilized in the recognition of the safety factor, methane concentration, in the system. And when conviction degree in recognition for methane concentration at the specified branch is too low, the system searches for other branch combinations in the branch relation table stored in the system, to use other ventilation transfer diagram of the specified branch. When a needed ventilation transfer diagram is not stored in the system, the expert system asks automatically the ventilation simulation from other computers linked to the main computer automatically. The system repeats consultation until conviction value of safety in the specified branch approached

Jan 1, 1993

By P. E. Sarquis, R. Lenzo

The concentration of barite by gravity separation generates substantial quantities of fine particle wastes, and it is estimated that =40% of the contained barite is lost to these waste streams. In this study, froth flotation was examined as a potential method for the recovery of fine-barite particles. The study included the use of kinetic equations to estimate the variables affecting flotation, batch-scale rougher flotation tests to study the flotation variables and an examination of alternatives for the cleaning of the rougher concentrate. Results indicated that a concentrate grade of 96.5% could be achieved with a recovery of 77.5%. Although barite flotation from industrial wastes is more difficult than direct barite flotation, the process has considerable economic potential.

Jan 1, 1996

By Joel K. Witt, Jackson G. Jenkins, Wendy M. Gort, Brent A. Whitman

A major concern for operators of leaching/SX-EW plants is a phenomenon known as gunk or crud. The build up of gunk is typically the result of fine particulates which are transported via the leach operation to the solvent extraction plant. The particulates develop into a solid layer that concentrates at the aqueous/organic interface. This can cause phase separation problems which can result in entrainment and other deleterious operating conditions. Most operations physically remove the gunk from the SX settlers and process it via a centrifuge or coalescer to remove valuable organic. While both methods have served for many years, Magma is currently evaluating the use of a chemical surfactant which induces a definitive separation of particulates from organic.

Jan 1, 1994

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By Andreas Rubo, Stephen Gos

In the days of increasing environmental and safety awareness many efforts have been made to prevent losses of both an evident economic nature and also less obvious losses. These losses could be associated with damages due to negative impact on the environment and also people coming into contact in a broader sense with any toxic chemical. This paper deals with how cyanide can be applied in a responsible manner at a modern gold mine. Responsible application is achieved by minimizing losses of reagent and avoiding negative impact on the environment as well as adopting a Responsible Care philosophy to the application of cyanide. It becomes evident that this is quite a complex system with a greater commitment than avoiding reagent losses for economic purposes.

Jan 1, 1997

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By G. S. P. Pereira, E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality overtime. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By P. Verhoeven, G. Hefter, P. M. May

The dissociation (ionisation) constant of hydrogen cyanide, pKa(HCN), has been measured by high precision glass electrode potentiometric titrations in saline solutions containing up to 5 mol/L sodium chloride. The dissociation constant of water that is necessary for the calculation of pKa(HCN) has also been measured. In saline solution, and in contrast to literature values, pKa(HCN) changes considerably at both high and low ionic strengths as a result of changes in activity coefficients. In addition an equation is presented, using literature data, that describes the variation of pKa(HCN) with temperature up to 150°C. The significance of the changes in pKa(HCN) for optimising the pH of alkaline cyanide gold recovery streams is briefly discussed.

Jan 1, 1991

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By A. Geertsema

Introduction Gasification of coal has been practiced for many decades for the production of gas, fuels, chemicals and power. However it has only more recently started to get significant attention in the USA. In this review of the basics the features of gasification as compared with combustion is covered and the potential of increasing the conversion of coal via gasification is indicated. After dealing with the fundamentals of gasification a review of gasification technologies will be presented with an indication of the widespread international and more limited US use of this technology. In conclusion the attention will be directed at the future prospects of gasification.

Jan 1, 2006