Search Documents

By Barry J. Hansen, Ruston A. Ford

Production of mine backfill from the tailings produced in a proposed Crandon concentrator is described. A process has been developed capable of producing suitable fill for the mining method selected for the Crandon orebody. It maximizes the placement of pyrite underground as fill and segregates tailings into pyrite and nonsulfide fractions. To determine the suitability and engineering characteristics of the backfill product for use underground, laboratory and physical stope simulation model testing was conducted. The results of the testing and the application of those results to the design of the backfill system ultimately affecting mine geometry and subsequent mine production will be presented.

Jan 1, 1981

By R. L. Beatty

Bond International Gold's Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989

By C. G. Anderson

Over the past 15 years numerous pressure oxidation plants for pretreatment of gold ores and concentrates have been installed throughout the world. While, this technology is now established, it suffers in term of the complex engineering and operational characteristics inherent in utilization of high temperatures (i.e. up to225°C) and high pressures (i.e. > 400 PSIG). This paper outlines the application of an industrially proven pressure leaching methodology utilizing nitrogen species catalyzed pressure leaching and alkaline sulfide gold leaching. As such, it stands as an economic and engineering advancement in pressure leach treatment of gold ores and concentrates.

Jan 1, 2003

ICMM’s vision is ‘a viable mining, minerals and metals industry that is widely recognised as essential for modern living and a key contributor to sustainable development’. The ICMM Sustainable Development Framework provides the basis for achieving this vision by assisting the industry to improve its performance. Two years on from the first SDIMI conference, significant progress has been made in further developing and implementing the Framework. To fulfill their commitment to implement and report performance against the ten sustainable development principles in the Framework, ICMM’s corporate members have committed to report ‘in accordance’ with the GRI 2002 Sustainability Reporting Guidelines and the Mining and Metals Sector Supplement, developed by the GRI and ICMM. While much remains to be done, development of the Supplement and the commitment to reporting mark an important milestone for ICMM and the sector.

Jan 1, 2005

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By Baron Miya, Keith Hanks, William Edgerton, Francis Fong

The City of Los Angeles capital improvement program includes the construction of a new 35-km interceptor sewer. This sewer will be built as a deep tunnel with finished diameters ranging from 2- to- 4 meters. The project will be constructed concurrently in two phases; an 18-km East-West and a 17-km North-South segment. The new sewer provides additional conveyance capacity for an existing deteriorating sewer that is scheduled for rehabilitation. Large sewage spills during the El Niño storms of 1998 resulted in a Cease and Desist Order that established an aggressive schedule for the completion of the project.

Jan 1, 1999

By P. Johnson, G. E. Jones, G. K. Hoffman, C. B. Krueger, J. S. Raugust, M. Wilks, V. T. McLemore

The NMBGMR is slowly converting historical data into a relational database using Microsoft Access 97. The purpose of this database is to provide data on districts, mines, and mills in New Mexico to government agencies, public organizations, industry, and citizens to make informed decisions about resource development, resource management, water supplies, environmental impacts, hazard assessment, and waste disposal. Once the data are entered into the database with locations, the data can easily be converted to GIS format for displaying as different map layers.

Jan 1, 2003

By Ronald E. Heuer

It is not possible to accurately predict water flow into rock tunnels during construction, because all of the relevant factors cannot be accurately determined ahead of time. But an estimate is needed, because water inflow can be a major problem during construction, hence also a major concern for project design. There currently is no simple, generally accepted method of estimating inflow. This paper describes a semi-empirical method for estimating possible water inflow based on borehole water pressure test results, using correlations from previous tunnel experience. The method provides an estimate of percentages of tunnel length which will experience different intensities of long term steady state inflow, and provides an estimate of possible initial heading inflow. The method is applicable for distributed sources of water inflow due to rock mass features such as systems of joints and bedding planes, and accounts for different boundary conditions of water head and recharge. The metric system flow units used in this paper are liters per minute (L/min) and liters/minute/meter of tunnel (L/min/m), to be compatible with rock mass classification systems commonly used today.

Jan 1, 1995

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By J. W. Leonard

Comments The venerable straight-line equation Y = Bx + A is again being rediscovered, but this time by economists, mining engineers and geologists. Two economists, William Sharpe and Harry Markowitz, from the University of Chicago and Stanford University, respectively, won the 1990 Noble Prize in economics by showing that the price of individual stocks can be related to the Dow Jones industrial average (DJIA) using the straight-line equation. According to Bill Chidester, Investment Analyst, Scientific Investment, Sharpe and Markowitz strongly emphasized the role of the beta (B) value while considering the alpha (A) value to be "pretty unimportant." Chidester claims that alpha is the "mystery" value that causes individual stocks to behave independently of popular stock-market indices, such as the DJIA. For many years, mining engineers and geologists have routinely called alpha the "nugget" or surprise element in geostatistical analyses in which a designated distance (x-axis) is related to the variance of the grade (y-axis). Because the influence of the independent variable (distance) over the dependent variable (grade variance) is ideal when alpha is equal to zero, any increase in alpha represents a loosening of influence or control within the relationship. This can be good news or bad news - good news if you are an economist sorting out off-trend stocks and bad news if you are a mining engineer trying to predict sulfur in a coal seam. With many mining trends, such as those involving the relationship of distance to the variance of grade, a mathematical relationship can be formed. In geostatistical analysis, the point where a mathematical trend ends is known as the sill. If the difference between the variance of grade at the sill and at alpha can be determined, then an estimate of the relative control for a given distance can be obtained by comparing the sill value to alpha. The extent to which alpha approaches the value of the sill provides an indication of independence or loss of trend. The alpha concept may find application with distance, time or fluid problems. The point of change can be either a change in trend or the trend limit. However, even without a clearly defined point of change or trend limit, increasing alpha values always infer loss of trend. Alpha analysis should be regarded as a valuable tool when sorting out many sets of mining data. The application of this user-friendly concept to reserves, material transport, fluid flow and other areas has been, and will continue to be, the basis of many important past and future developments in mining and geology.

Jan 1, 1996

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By Pascale St-Germain, Michael Li, Lionel J. J. Catalan

The oxygen flux into water-covered reactive sulphidic tailings is required for evaluating the long-term performance and predicting the quality of engineered shallow water covers. This information can also serve as an input to the design of water covers for reactive tailings decommissioning. This paper describes some dissolved oxygen (DO) profiles recently measured in the field across the tailings/water interface and oxygen fluxes derived from these profiles. These fluxes are compared with previously reported flux values from similar field measurements. Techniques and pitfalls for measuring DO profiles and calculating oxygen fluxes are also discussed.

Jan 1, 2000

By Johanna I. Wong, R. John Caulfield, Victor S. Romero

The existing Hetch Hetchy water system, owned and operated by the San Francisco Public Utilities Commission (SFPUC), serves 2.4 million people within the San Francisco Bay Area. The system has existing 1920s-era pipelines crossing under the Bay that are vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The SFPUC plans to replace the pipelines with the first TBM-driven tunnel underneath the San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance machine. The new tunnel will pass under environmentally sensitive habitats and will be approximately eight kilometers (five miles) long with no intermediate shafts. The project challenges will include tunneling through a prominent buried bedrock ridge that transects the alignment and through soft soils under the Bay. Seismic performance criteria include maintaining service flows after a large earthquake on one of the active faults in close proximity to the project site.

Jan 1, 2007

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By F. Michael Jenkins, Elaine T. Bowers

Longwall systems are used to mine approximately 50 pct of the world's total coal production. Single entries are the predominate method of longwall development in Europe and Asia where mining conditions are much more severe than those encountered in the United States. During the 1970's and early 19801s, the Bureau of Mines and the coal mining industry invested nearly $20 million in single entry and related research. This report reviews the accomplishments of single-entry research in the United States. Two U.S. single-entry field projects are described; the Sunnyside Single-Entry Project conducted in central Utah, and the Tunnel Boring project conducted in northern West Virginia. Two other important studies are discussed, the Single-Entry Study by NAMCO and the Single-Entry Design Study by Ketron. Inc. This review compares the resulting technology with European counterparts to further assess the utility and efficiency of the U.S. systems, and final1 y, it discusses future research and development options which would lead to safe and productive single-entry longwall development in this country.

Jan 1, 1986

By H. Bogart

The Golden Sunlight Underground Mine located near Whitehall, Montana was portalled from the bottom of the existing Golden Sunlight Pit in July 2002. Gold was mined by sublevel stoping in the larger ore zones and longhole back stoping in the narrower ore zones. The stopes varied from 30 feet to 100 feet in width, extended up to 200 feet in height, and were completely unsupported. Underground production averaged 1,500 tons per day with a staff of35 people. The mine operated with a break-even cut-off grade of0.080 ounces per ton.

Jan 1, 2004

By James F. ` King

This paper reviews the changes which have taken place in the supply of smelter-grade alumina and refinery-grade bauxite over the past twenty years. It highlights the current situation and identifies some trends which are to be expected in the medium- and longer-term future.

Jan 1, 1986