Search Documents

By C. A. Pickles, S. J. Splinter

Silicon oxynitride, Si2N20, has many of the intrinsic properties of a potential high temperature engineering ceramic material. Some of these properties are similar to those of silicon nitride, which has been more intensively studied. However, although silicon nitride ceramics are approaching a state of microstructural refinement for various engineering applications, silicon oxynitride has received little attention. This has been mainly due to a lack of an economical and reproducible method of producing pure crystalline Si2N2O. Several reports exist on the preparation of crystalline Si2N2O from SiO2 and Si3N4, yet very little kinetic data exist. Even less is known about the carbothermic reduction of SiO2 in a nitrogen atmosphere to produce Si2N2O. In this paper, a review of the properties and methods of preparing silicon oxynitride will be presented. In addition, results obtained by reactively sintering SiO2 and Si3N4 will be discussed. The overall reaction is as follows:

Jan 1, 1990

By J. D. Pitts

Long distance slurry pipeline systems for steam coal, iron concentrates, copper concentrates, and limestone, first used nearly 60 years ago, are now transporting nearly three billion ton-miles annually. At this time a phosphate concentrate pipeline is nearing start-up and systems for transporting coking coal, lead/zinc concentrates, and fly ash are planned. The solids pipeline concept was first patented in the early 1900's and put into practice in the 1950's. Table 1 summarizes the major elements of several presently operating commercial systems. Increased control system sophistication has been accompanied by significant drops in control equipment size and cost, as illustrated by recent cases of pipeline operation with progressively more advanced level of control: 1) The Consolidation Coal (Ohio) and Savage River (Tasmania) iron concentrate pipelines started in 1957 and 1967, respectively, used simple hard-wired control logic. 2) The Black Mesa (Arizona) coal slurry pipeline commissioned in 1971 added a hard- wired programmable logic controller for some of the start-up and shutdown routines. 3) Two years after its start-up in 1974 the Pinto Valley (Arizona) copper concentrate pipeline was tied into the concentrator digital computer system for data logging. 4) The Samarco (Minas Gerais, Brazil) iron concentrate pipeline which came on-line in mid-1977 was the first slurry system to use a dedicated supervisory computer for its control. Communication to remote areas was via micro- wave and buried cable.

Jan 1, 1979

By Nelson R. Shaffer

Glamorous, burgeoning biotechnology and mundane industrial minerals would at first glance seem to share little in common, but in truth, modern biotechnology depends on many minerals. Biotechnical processes also can be used in industrial mineral extraction and processing. Biotechnology is broadly defined as the application of biological organisms, systems, or processes to manufacturing and service industries. Genetic engineering has reinvigorated one of mankind's oldest sciences, biotechnology, into a booming business. Many modern processes depend on microorganisms cultivated under very stringent conditions in bioreactors. Minerals from carbonate, sulfate, chloride, nitrate, phosphate, and silicate families are used to provide essential nutrients and to regulate growth conditions (such as pH) in order to assure optimal growth of organisms. Certain cells or enzymes perform better when immobilized upon or within solids, and minerals are often used to immobilize cells, especially in continuous process. Minerals are also used extensively in separating and purifying products of biotechnology. Diatomite, zeolites, and silica are especially useful in purification processes. Industrial minerals also are commonly used to clean up large volumes of process water that must be treated. Biotechnology can be employed in exploration, extraction, and processing of geologic materials and in reducing mining or other environmental problems through bioremediation. Microbes have been shown to solubilize certain elements and so promote extraction of heavy metals, phosphate, aluminum, potassium, and even rare earth elements. In a related technique, unwanted materials such as pyrite impurities can be leached microbially to produce cleaner products in sand and clay industries. Microbial actions can modify surface characteristics and so enhance certain ceramic properties. Certain organisms can accumulate useful elements from dilute sources; others can transform unusable chemical species to more useful forms. Deterioration of stone, concrete, and even glass or brick, can be accelerated by microorganisms. Control of such biodeterioration could improve long-term performance of industrial mineral products. Microbial processes have shown promise in improving several mine-related problems. Certain bacteria help remove clays from phosphate slimes and other suspensions. Others are used to degrade cyanide or other organic chemicals such as floatation aids. Cells immobilized on clays have been especially efficacious in bioremediation. Biotechnology industries, like the industrial minerals industries, encompass huge ranges of materials and processes. Costs of products from these industries range from pennies to thousands of dollars per unit, and their products are vital for maintaining modern life styles. Many biotechnical processes depend upon industrial minerals and certain biological processes can be harnessed to do useful tasks in the minerals field. The interplay of industrial minerals and biotechnology is important today, and as biotechnology advances, its interaction with the industrial minerals industry can only increase.

Jan 1, 1995

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By Adrian E. Scheidegger

Recently, a new theory of the subsidence of rock masses has been advanced by Litwiniszyn and coworkers, which is based on the notion that the individual rock particles perform random walks. It is shown in the present paper that the final equations of the random walk theory can be justified from general principles of statistical mechanics in which no specific theoretical model of particle behavior has to be made. The theory appears to account appropriately for subsidence phenomena.

Jan 1, 1966

By S. P. Banerjee

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1987

A chartered bus with about 30 attendees of the just completed 1998 SME Annual Meeting headed toward Green Cove Springs, FL, which the author had been told was located somewhere south of Jacksonville, FL. In conjunction with the meeting in Orlando, RGC (USA) Mineral Sands provided a tour of its facility. The author had worked with heavy minerals on a laboratory scale, performing the usual gravity and magnetic separations, but had never been to a heavy mineral mine and processing facility. Years ago as a metallurgist, the author once applied for a job in a heavy mineral operation in Florida -it may have been the same operation. After turning north on to Highway 95, the endless billboards promoting beach-front retirement communities proved the Atlantic ocean was just a few miles away (although the author never caught a glimpse of it). After another hour, the bus suddenly turned west and continued inland for about 65 km (40 miles). The thought occurred, "We are talking about beach sands, what are we doing heading away from the ocean?" As the bus continued inland, the author was struck by the flatness of the land and by the lakes, rivers and wetlands. He was also impressed by the many fine stands of pine and hardwoods. The office of RGC (USA) Mineral Sands is located about 16 km (10 miles) south of Green Cove Springs. Upon leaving the bus, members of the tour were greeted by Graeme Sloan, general manager, and Elliot Mallard, manager of mining. They provided some general information about the operation, including a slide show. RGC's Florida operation produces four concentrates: zircon (ZrSiO,), rutile (TiO,), ilmenite (FeTiO,) and leucoxene (an alteration product of ilmenite containing 67% to 70% TiO,). With a work force of about 170, the annual production of the above products is about 23,27, 45 and 14 kt (25,000 30,000 50,000 and 15,000 st), respectively. RGC also has other mineral sand operations, in addition to gold and base metal mines, mostly in Australia.

Jan 1, 1998

By J. J. Moore, B. Mishra, D. L. Olson

The production of radioactive and reactive metals, such as plutonium, uses various pyrometallurgical techniques that generate significant quantities of waste salts contaminated with hazardous, reactive or radioactive materials. Health concerns, environmental regulations and economic considerations require proper mitigation processes to recover the valuable components and for recycling or unrestricted release of these salts. The Oxygen Sparging Process converts soluble metal halides, such as chromium-, plutonium-, cerium chlorides, into insoluble oxides and/or oxychlorides which can be consolidated and separated for long-term storage or further processing. The matrix salt phase, viz. calcium and/or alkali chlorides, are clean after oxygen sparging and fit for recycling. This method has been described and its optimized parameters discussed to show that RCRA regulated elements, such as, chromium, lead, cadmium, etc. report to the consolidated phase making the salt recyclable. Salt Scrub Reduction Process for the recovery of radioactive and RCRA metals from the waste salts has been developed. The process uses a Ca-Ga intermetallic alloy which recovers over 98 percent of the reactive metals. The matrix salt phase in this process, viz. calcium or alkali metal chlorides, are clean after salt scrub reduction.

Jan 1, 1995

By D. S. Choi, H. D. Dahl, D. L. McCain

The paper examines current room and pillar mining practice in the U.S.A. from the standpoint of rock mechanics. Consideration is given to the deformation characteristics of the roof formation and the coal seam as determined in the laboratory as well as in the field. The results can be utilized by the practicing mining engineer to improve current mine design practice.

Jan 1, 1982

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By Jeffery Denit, Steve Hoffman, Van Housman

The Environmental Protection Agency (EPA) is in the early stages of developing a national mining waste program. Our goal is to develop a mining waste program that will be state implemented, multimedia in nature, flexible, utilize and enhance existing state programs, and protect the environment. The Agency appreciates the cooperation the mining industry is providing through its participation in the Policy Dialogue committee on Mining and by providing the Agency with technical data. The following is a discussion of what led to the development of a national mining waste program, the agenda initiative to evaluate Toxic Substances Control Act authority in phosphate manufacturing, and the important steps being taken through the Policy Dialogue process to frame and discuss issues. EXTRACTION AND BENEFICIATION OF ORES The Resource Conservation and Recovery Act of 1976 (RCRA) and subsequent amendments created a framework for the regulation of hazardous wastes under Subtitle C and nonhazardous waste under Subtitle D. In 1978, initial regulations were proposed for hazardous waste management units under RCRA. These identified a universe of special wastes that were large volume, low hazard and less amenable to Subtitle C control techniques. EPA noted that waste materials from the "extraction, beneficiation and processing of ores and minerals m fit these criteria. In October 1980, Section 3001 of RCRA was amended. This Bevill amendment excluded solid waste from the extraction, beneficiation and processing of ores and minerals from regulatory control under RCRA's hazardous waste Subtitle C. This was done pending a report to Congress and a regulatory determination regarding the Subtitle C status of these wastes. Thus in November 1980, EPA published an interim final amendment to the RCRA Subtitle C regulations to reflect the Bevill amendment. RCRA requires EPA to perform studies and make reports to Congress regarding the management methods and potential hazards of managing waste. RCRA also calls for a regulatory determination regarding whether Subtitle C (hazardous) or D (non- hazardous) controls are warranted for these wastes. In December 1985, EPA submitted a report to congress entitled, “Wastes from the Extraction and Beneficiation of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale." In that report, EPA found that some mining wastes exhibit hazardous characteristics, that the range of risk from mining waste is broad, and that waste management practices have caused environmental damage. In July 1986, EPA published a regulatory determination based on information gathered in the 1985 report to Congress and comments from interested parties. In the report, EPA concluded that RCRA Subtitle C regulation of extraction and beneficiation wastes was unwarranted because mining wastes tend to be disposed of in arid climates, waste volumes are high, and facilities and wastes are located in sparsely

Jan 1, 1992

By V. Karra

Based on extensive investigations on the effect of design variables on process performance, during 1982-85, Nordberg developed a 1000 hp cone crusher, with the objective of boosting crushing productivity in existing plants. The 2390 fits on the same foundation as the 7' SHD Symons cone, but is designed to give two times the capacity of the 7'. The economies of scale involved give the customer substantial cost savings. In this paper process performance of the Nordberg 2390 relative to the 7' SHD Symons cone, while crushing the same ore, will be presented. Also, implications of such a crusher scale-up to associated cost savings will be addressed.

Jan 1, 1988

By Panlop Huttagosol

The use of computer models to design ultimate pit limit of an open pit mine during its feasibility study has become an emphasized procedure in mining. It is a normal practice in open pit mine design to generate the most profitable final pit limit. The limitations of designing this optimal pit limit have been the requirement of significant computing efforts as well as the use of complicated operations research techniques. In an attempt to describe a computer method that has an easy conceptualization and is able to provide a precise and desirable solution, a new technique is developed. The ultimate pit limit problem is formulated as a large scale transportation problem. The formulation is based on the use of a three dimensional block model to represent an ore body and surrounding materials. The solution technique is developed through solving the dual system of the formulated problem by using the adapted simplex algorithm of linear programming. The implementation on given case studies demonstrates that the new method is capable of providing an optimum pit value. The computing effort required by the algorithm is still the main constraint in solving a large scale problem. The technique provides open pit mine planners with an alternative tool in using a commercial linear programming software which is capable of solving a general transportation problem. The selected software must be able to handle a large scale problem, and it needs an additional effort td formulate the problem and transform a result into the ultimate pit limit solution.

Jan 1, 1992

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By Steven Schurman

Acid Rock Drainage (ARD) is one of the most serious and persistent pollution problems facing today's mining industry. ARD is formed when pyrite (FeS) is exposed to natural weathering conditions. Pyrite weathering, formally the oxidation and hydrolysis of pyrite, leads to the generation of soluble, hydrous iron sulfa-salts and the production of acid in the form of H+. The resulting effluent is water that is characterized by high levels of iron (and any other metal contained in the rock undergoing weathering) as well as high concentrations of sulfate and a low pH (acid). Rocky Mountain Remediation Services, L.L.C., has developed a patents pending Envirobond'™ product, Envirobond™ ARD, to treat acid rock drainage. Treating pyrite with Envirobond™ ARD inhibits the oxidation and hydrolysis of pyrite thus curtailing the pyrite oxidation cycle.

Jan 1, 1999

By Takahide Wakamatsu, Junji Shibata

Complex polymetallic sulfide ore deposits occur in Tohoku district, northern part of Honshu island, Japan. The ore is locally called "Kuroko” ( black ore ) and is compactly composed of fine grained sulfide minerals of such principal metals as copper, lead, zinc and iron. Currently one of Kuroko mill plants is producing such concentrates as copper, lead, zinc, pyrite, barite, and clay minerals, mainly employing differential flotation techniques. This paper describes briefly the progress of techniques in Kuroko processing over the past thirty years and also the present state of Kuroko processing and its challenges to be studied and overcome in the future.

Jan 1, 1989

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023