Search Documents

By W. R. Bush

Radiation protection in uranium mines and nuclear reactors is compared, with the objective of determining if any radiation protection practices which have worked well in one area can be adapted to the other area, especially from reactors to mines since radiation protection is more highly developed in reactors. Several areas are identified where improvements can be made in radiation protection in mines, the most important being improvement in ventilation at the workplace, greater attention to special monitoring during upset conditions, and a need for a substantial increase in radiation protection staff. It is concluded that, although considerable room exists for improvement, the general approach to radiation protection presently being followed seems appropriate for the circumstances encountered in mining.

Jan 1, 1981

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By J. C. Barker

Alaska, with about 74% of the US continental shelf, is largely unexplored for placers in its vast shallow marine waters. Nevertheless, there are numerous occurrences of marine minerals including gold, platinum, and cassiterite. Offshore dredging has recently begun in the Nome area. State and Federal agencies are preparing additional acreage for leasing. With 76,200 km (47,300 miles) or 54% of the US coastline, Alaska is a vast, largely unexplored frontier for shallow-water marine placers. Despite the general lack of mapping and only sporadic past prospecting, many prospects are known and a major mining operation for gold has recently begun offshore of Nome. Due largely to the demonstrated success of the Nome operation, the US Minerals Management Service is preparing to conduct a lease sale of additional acreage further offshore from Nome. And future sales are being considered elsewhere by both the Federal and state leasing agencies.

Jan 1, 1990

By Danqing Xu, A. W. Khair

This paper presents an analysis of mechanism of secondary fragmentation and respirable dust generation due to regrinding. In continuous miners, the recovered coal and uncleaned coal from the previous cutting cycle have to be transported through the circumference of the cutting drum, subjecting the coal to regrinding. Such regrinding comminutes the coal material utilizing kinetic energy, thus creating a great amount of respirable dust. The mechanism of a single particle subjected to regrinding is analyzed. A mathematical model is developed to describe regrinding in field conditions. The important factors influencing the comminution process are discussed in detail. Utilizing three types of coal seams, laboratory experiments are being carried out with an Automated Rotary Coal Cutting Simulator (ARCCS) to quantitatively evaluate the effects of some particular parameters, such as cutting velocity, depth of sump and properties of coal material, on breakage and on the amount of respirable dust generated. An orthogonal fractional factorial experimental arrangement is used to optimize experimental design. Preliminary experimental results are presented.

Jan 1, 1991

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the fol¬lowing corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. • Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, Wv. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its im¬proved accuracy and ease of computerization. • Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1989

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

By Ji Changsheng

In a large surface mine design, different kinds of mining equipment can be selected. Even though the major purpose of capital investment is to get more profit from mining activities, there are some other complicated factors which influence the selection of mining equipment must be considered as well. A fuzzy evaluation model with fuzzy set theory is proposed in the paper to make a good selection of mining equipment in which different kinds of factors including quantitative and nonquantitative ones can be taken into account at the same time. With the model, mining equipment selection of a large surface mine can take into consideration not only economic factors but also some other factors which play important role in mining system.

Jan 1, 1996

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

By Pierre M. Gy

The final purpose of exploration is to esti- mate the grade and tonnage of the various qualities of ore contained in a given mineral deposit. This estimation cannot be directly carried out on the whole of the ore body. It usually requires four steps: Core Drilling Campaign The ore body is represented by a series of cores further divided into core sections of equal or unequal length. Core Splitting The core sections are longitudinally split into two halves: the first half is kept for various examinations and physical measurements, and stored for further reference; the second half (core sample) is used for determination of the chemical analysis. Core Sample Reduction The chemical analysis cannot be directly per- formed on the core samples. It requires the constitution of assay portions usually weighing from a few decigrams to one gram (more in precious metals assaying) and passing through a 100 or 150 mesh screen.

Jan 1, 1979

By H. Nakazawa, A. S. Malicsi, K. J. Reid, P. J. Ryan, I. Iwasaki, P. W. Weiblen

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Reasons for low recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron microprobe, scanning electron microscope, and scanning Auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures that have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their application to the flotation recoveries of precious metals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1987

By Douglas J. Piper

On reflection of certain overall circumstances which have pervaded the gold mining industry, it appears useful to point out some specifics which the writer hopes will improve the potential for success in the application of hydraulic dredges to gold mining activity. I will, prior to entering into that discussion, comment briefly on rule of thumb for the application of the three types of equipment. The three are bucket line, bucket wheel and drag line dredges. From a standpoint of high volume movement over a short distance, between 50 and 300 feet, the drag line dredge is historically the most cost effective type of machine to be utilized if bulk excavation is the single driving consideration. It is typical for this sort of equipment to operate in the 10 to 30 cents per cubic yard range, however, cost of operation is not the sole consideration. Typically the drag line mixes and remixes the material which it excavates. In the event that gold recovery is the object of the exercise, a strong potential for loss of the valued mineral exists. Additionally, drag lines do a poor job of bottom cleaning, particularly if there is a ridged or creviced bottom which must be cleaned and in some cases partially removed to assure recovery of the highest percent of valuable ore. The bucket line dredge has, until recently, been considered an extremely cost effective device. However, the high cost of manufacture of this type of equipment has mitigated against its use in the majority of

Jan 1, 1992

By Harleigh V. S. Tingley

Investment in the mining industry has increased substantially throughout the world in recent years. So have acquisitions, divestitures, and financial restructurings. The return of outside investors to the industry is welcomed. The trend toward stockholder litigation is not so welcomed. Both have provided the impetus for commissioning outside professional due diligence studies of potential minerals transactions. For a number of reasons, some unique to the industry, evaluation of mining investments is a challenging task for the investor. Investments in exploration prospects and undeveloped properties have a high speculative content. Buyers pay for uncertain future prospects. Alternatively, most developed mining investments are large and long-lived and cannot easily be modified during that life. Even so, to be successful, they must compete in an environment in which their reserves - the source of their profits - are often imperfectly known. And markets, competition, technology, and politics are among the many continually changing factors that affect investment performance. Minerals investment evaluation is further complicated because each minerals investment has its own singular combination of risks and opportunities. Each ore type and each ore body presents different problems in reserve evaluation, mining, and extraction. Each minesite has its own often unique combination of mine, infrastructure, political, environmental, and other risks. And the key requirements for commercial success differ substantially among various minerals.

Jan 1, 1990

By Gary A. Perry

Cyprus Sierrita produces copper and molybdenum from its Sierrita and Twin Buttes open pit mines south of Tucson, AZ. Both pits were started in the late 1960s and are more than 460 m (1500 ft) deep. Sierrita has used a Caterpillar 992C Remote Controlled Loader since January 1993. The loader was justified to increase safety and profits at Sierrita. It has exceeded all expectations. As of June 1993, the 992C had produced additional profits of more than $1.5 million. Safety and Geotechnical The safety of Cyprus personnel and equipment is always of prime concern. The remote controlled loader removes personnel from the active raveling area. But it requires prudent operation. The remote controlled loader discussed here is always intended to be used in a safe manner under a managed slope. Any increase in slope angle or use of any equipment under a critical slope is taken only after careful analysis of the specific

Jan 1, 1994

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By Leo J. Laughlin

In recent years, heavy mining applications have put an increasing demand on conveyor pulleys. This has resulted in the increased usage of turbine pulleys. The designs of these pulleys are often based upon the failures seen in the conventional welded designs, overlooking the interaction of pulley-shaft system components as the profile of the disc is modified. This paper will focus on the development of balanced design philosophy using case studies of turbine pulleys in heavy mining applications, evaluated with FEA.

Jan 1, 2002

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999