Search Documents

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By Nicholas Kyriazia, John P. Shubilla

A performance study of oxygen self-rescuers of varying durations from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested on a Breathing and Metabolic Simulator in the Life Support laboratories of the Bureau's Pitts- burgh Research Center. Parameters monitored during the testing were inhaled levels of C02, 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60-min man-test 4, as described in 30 CFR 11H. Results presented include apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1986

By Y. H. Chia, P. Somasundaran

Carrier flotation of anatase from clay using coarse calcite is investigated, together with relevant basic properties of the system including aggregation and zeta potential, under different chemical and hydrodynamic conditions The roles of carrier sue and amount also are considered Mechanisms responsible for selective aggregation and flotation are reviewed

Jan 1, 1983

By Peter W. Willcocks

The Cyanide Regeneration Process (CRP) was developed by Golconda Engineering and Mining Services and installed at Golconda's Beaconsfield Gold Tailings Retreatment Project situated in Tasmania, Australia. The Tailings Project is a 1000 ton per day carbon-in-pulp treatment plant, feed for which consists of tailings material which is dredged from the Tamar River. The pulp is screened to remove debris, then cycloned to form two products. Underflow pulp is stored in a 350 ton bin and cyclone overflow passes to a thickener. The coarse pulp material is fed to the grinding circuit then rejoins the thickened slimes in the cyanide leach circuit. Gold is extracted by carbon-in-pulp techniques. The plant is sited in rolling, hilly country approximately 200 meters from the Tamar River. The residue disposal area is quite small consisting of four dams, totalling 42 acres. The regional climate is cool and wet with little evaporation; therefore, we anticipated a net increase in contained liquor, and subsequent storage problems. Our plan was to remove cyanide from the liquor prior to returning the detoxified solution to the river system. Such treatment was not required until midway through the second year of the project. Initial testwork on sample material indicated that destruction of cyanide by chlorine was the simple solution. Subsequent follow-up on actual plant liquor indicated a huge chlorine requirement due, we believe, to the substantial degradation of vegetable matter plus organic content from the marine environment. The cost of cyanide destruction could not be justified.

Jan 1, 1998

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states, and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies important problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2003

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By L. L. Oriard

The author describes three case histories of fracture-control blasting demonstrations. This is a technique in which the walls of blast holes are scribed or notched in order to enhance the development of blast_induced fractures, and to control their direction. One demonstration was that of a tunneling application in a rock that was generally competent but strongly foliated, hence strongly anisotropic. P second test was conducted for perimeter blasting of a structural excavation in a massively jointed limestone. A third field test was conducted for tunneling through an old concrete structure. Increased applications are envisioned with new tool modifications being developed at the University of Maryland.

Jan 1, 1981

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By J. C. Norman

The boron review arrived too late to appear in the June issue. The United States was the world's second largest producer and the largest consumer of boron compounds during 1991. According to the US Bureau of Mines, boron mineral concentrate and chemical production in the US totaled about 1.1 Mt (1.2 million st), yielding about 608 kt (670,000 st) of BO, in 1991. Total estimated value was $440 million. That level of production was equal to 1990 revised production figures. Value was greater by $37 million, however, reflecting a strengthening of boron product prices. The US continued to supply essentially all its own boron while maintaining a strong position as a source to foreign markets of sodium borate products and boric acid. Domestic employment in the mining and beneficiation of boron products in 1991 remained at 1100 people, about the same level as in 1989. The Bureau of Mines estimated total world production of boron in 1991 - mineral concentrate and chemical - at about 2.9 Mt (3.2 million st). That corresponds to about 1.2 Mt (1.3 million st) of BO ,. World production in 1991 was about equal to revised 1990 levels. US production Mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals in 1991. US producers, in order of quantity of production, were US Borax and Chemical Corp., North American Chemical Co., and American Borate Co.

Jan 1, 1992

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

By Thomas F. Pugsley, Wilf J. Davies, James Gallagher

Falconbridge Limited is developing a major nickel mine at Craig which lies between 600 m, 915 m and 1500 m below surface and is accessed on the 600 m and 1250 m levels of Onaping Mine. To supply adequate ventilation for mine development and initial ore production, two raises, 1200 m long are to be driven in norite and granitic gneiss. Falconbridge has purchased a Robbins 97RL Raise Drill and a string of 330 mm drill pipe to ream these raises in 600 m legs at diameter. The paper describes the introduction of deep hole, large diameter raise boring technology into Falconbridge operations involving contractors and specialists in the technology.

Jan 1, 1989

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By M. A. Trevits, R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water-bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited number of studies have been conducted that characterize hydrologic changes and also quantify the magnitude of mining-induced subsidence. The US Bureau of Mines (USBM) conducted such a study at a mine site in Greene County, PA. A total of eight water wells were drilled, and hydrologic parameters, such as specific capacity, transmissivity and well yield, were determined both before and after mining. Electronic water-level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1993

Rinker Materials Corporation (Rinker) operates construction aggregate operations in 15 states across the US. Thirteen of those operations are located in Florida, where Rinker produced approximately 40 million tons of aggregates in 2002. Because the deposits being mined in Florida are shallow sedimentary deposits of limestone and natural sand, with the deepest being approximately 75 feet deep, abundant acreage is mined annually. Rinker mines about 300 acres/year in Florida alone, and because there are so many wetlands and complete avoidance is nearly impossible, there are also wetland impacts. Thus, there is ample need for reclamation and mitigation, which presents an opportunity to involve local school groups with the planting and monitoring of these various projects. Rinker has successfully worked with a half dozen or so schools on these projects, involving students from grade school through college, with surprising success and outstanding results.

Jan 1, 2004