Search Documents

By Gary W. LaChapelle

Cyprus Miami Mining Corp. has a history of overcoming adversity through innovation and adaptation to changing conditions. Requirements to remain profitable in the 1990s include a combination of advanced technology, employee involvement and training, attention to customer satisfaction, environmental awareness and quality management. The Miami property is located in the Globe-Miami area of Arizona, 130 km (80 miles) east of Phoenix and 160 km (100 miles) north of Tucson. The complex is located in a high desert environ¬ment at an elevation of 1065 m (3500 ft). The region receives about 480 mm (19 in.) of precipitation annually. History Mineralization at the Miami property was first discovered in the 1880s, which led to underground mining of copper by the 1890s. In 1911, the Inspiration Consolidated Copper Co. was formed by combining the Inspiration and Live Oak Mines. Full-scale production began in 1915. Block caving methods were used at both mines. Open-pit mining commenced in 1948. Underground mining had ceased by 1954, and all production was obtained from surface operations. Innovation has been the key to Miami's success. Development of sulfide flotation and the ferric cure process for vat leaching were advanced at Miami. In situ leaching of oxide material, remaining after block caving had removed the sulfide ore, was also used.

Jan 1, 1993

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By Norbert Steiner, Roy Norcross

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O2 instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O2 with SO2 yielding H2SO4 up to 70% strength, depending on off-gas tem­perature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentra­tion, residual SO2 concentrations of less than 20 mg!Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O2 process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By William P. Shinn

The site of Pittsburg from the first knowledge by white men of its location has been regarded as a position of great strategic importance.

By H. Walqui, A. Buendía

The Toquepala concentrator expansion project incremented the capacity of the existing concentrator by 15,000 Metric tons per day (t/d), from 45,000 to 60,000 t/d. The plant is located in southern Peru,1,200 km southeast of Lima. The implementation plan for the expansion project was based upon an engineering and procurement contract, and a construction contract. The overall Project Management was by Southern Peru Copper Corporation (SPCC). The expansion followed a very aggressive schedule that considered a construction period of only ten months, with minimum interference to the existing facilities. Major equipment was purchased during basic engineering. This paper details the design, construction, and commissioning of the 6.4 m diameter by 10.2 m long ball mill, and the performance of the milling circuit during the first two months of operation.

Jan 1, 2003

By Scott E. Broughton, Robert T. Tape

Heap leaching requires containment and storage of cyanide solutions, the volume of which may increase dramatically following an extreme storm event or extended wet periods. This paper describes a computer operated solution storage model developed to assist in the management of these requirements. It results from the accumulative efforts of various Klohn Leonoff engineers working on a number of heap leach projects throughout the western United States for the past several years.

Jan 1, 1988

By Mary Korpi

So now you ask, Where are the transcripts? The well-organized co-chairs, Harry and Mary, did their job. Doug Halbe was active in the audience encouraging people to speak up and keeping everything moving along. So where are they? Were the comments so provocative that they could not be written? Was the profanity so bad (even for miners!) that it couldn&apos;t be repeated? It appears that at the first session of the Plant Operators&apos; Symposium a glitch occurred with the recording equipment. Thanks go to everyone who did comment during the dis- cussion period. The People I session had a lot of lively conversation and we are sorry that it will not be printed. However, there is now another reason to hold the plant operators&apos; sessions on a regular basis! Another People session can and will be held in the future.

Jan 1, 1998

By G. R. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring previously overlooked ore districts in Oregon. In eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many prospects. Arsenic, mercury, and gold are geochemically anomalous but silver is usually not. The epithermal deposits are located in part of the Deer Butte formation or equivalent units. Exploration criteria include the presence -of Deer Butte formation or equivalent units and northwest structures cut by north-south basin and range structures.

Jan 1, 1987

By J. W. Jang, J. J. Moore, I. Iwasaki

The wear behaviors of grinding media with different chemical composition and microstructures in wet grinding of a quartz-pyrrhotite mixture were investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation behaviors. The galvanic interaction between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive condition in a slurry. The rates of formation of passive film controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1990

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

The US Geological Survey (USGS) held a one-day workshop at its Denver, CO facility to inform the public of the status of its National Mapping Program. In addition, the agency wanted to obtain information from topographic map users on what their needs are. The agency wants to know what the topographic map user wants. The USGS faces the challenge of keeping up with the changing needs of the nation. In the last few years, the agency has changed dramatically to meet these needs. For example, the "new" USGS incorporates mineral-information specialists from the former US Bureau of Mines and also uses the expertise of former National Biological Service employees. These areas complement the agency&apos;s traditional strengths in mapping, geology and water re- sources. The stated mission of the USGS&apos;s National Mapping Division is to "meet the nation&apos;s need for basic geospatial data, ensuring access to and advancing the application of these data and other related ears science information f& users worldwide." To accomplish this goal, the USGS publishes topographic maps, including shaded-relief editions of areas of special interest (state maps and national parks); photo image maps; satellite image maps; geologic maps and hydrologic maps. The geologic maps include geologic quadrangle maps, oil and gas investigation maps and charts, and coal investigations maps. The familiar 7.5-minute series topographic maps are the most widely used. The 7.5-minute- (1:24,000-scale-) format mapping was begun in 1935.

Jan 1, 1998

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By John F. Shea

When Dick Robbins asked me to give a keynote address, I felt it might be in order to review some of the practices and techniques used in tunneling and work up to some of the concepts now used to mine and construct tunnels. Needless to say, there have been many changes in tunneling technology and also many changes in the Safety Codes controling them. An example of this latter change was the fact that in 1931, my father excavated the Owyhee Tunnel No.5 with gas locomotives. He was able to do it because there was no natural gas in the rock and the ventilation system was designed to free the tunnel atmosphere from powder and exhaust fumes. Today OSHA rules would never permit gas locomotives underground, although there were no incidents on this particular project. One of my first tunnels, as Project Manager, was the Clear Creek Tunnel for the Bureau of Reclamation. Our method of handling muck was the Conway Muckers. This unit was a valuable improvement to the hand mucking of previous generations. The Conway was also used in our Navajo Project, in New Mexico. Unlike the Clear Creek project, where water was one of our main problems - up to 7,200 gallons per minute, at a pressure of 395 pounds per square inch - in the Navajo Tunnel, we had a mixed face which caused a major problem with our support system. In one of the Navajo Tunnels, there was a major cave-in, when the squeezing shale came in during an attempt to strengthen the support system. Although moving shale was not a constant problem, there were areas where the shale was five to six feet above the spring line.

Jan 1, 1976

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By C. A. Wiggins, J. M. Kennedy

The Benbrook Connection tunnel forms approximately 6,666 m (19,560 ft) of17,678 m (58,000 ft) of raw water pipeline connecting Lake Benbrook with the Rolling Hills Water Treatment Plant. This connection is designed to minimize costs to the owners, the Tarrant Regional Water District, for providing raw water to its’ various clients. The geological formations through which the tunnel passes and the design requirements resulted in some-what unique applications of initial ground support systems which were modified by the con-tractor to optimize the mining operations. The pipe sections, fabricated in 12 m (40 ft) sections, are concrete lined and coated steel pipe. Construction of the work shaft and tail tunnel was also modified to suit the contractors methods. A Lovat universal TBM was chosen to excavate through the various rock types. The pipe sections will be transported using beam carriers.

Jan 1, 1997

By R. A. Womack, Alex Ruzycki

Over the past six years, 4.5 million tonnes (5.0 million short tons) of gold ore have been heap leached at the Alligator Ridge Mine. Ore is leached in successive lifts, resulting in heap heights of 20 m (66 ft). Recoveries from each lift are determined through an extensive post-leach drilling program. The relationships between heap height, recovery rate, ore preparation, heap construction, and leach solution application are discussed.

Jan 1, 1987

When multiple mines operate in an area there are social, economic and environmental impacts which cumulate over space and time. These impacts require special attention. A collective approach is required to identify, assess and manage them. No assessment of sustainability of mining can be considered complete without accounting for cumulative impacts. This paper proposes a framework and typology to deal with cumulative impacts and tests this in a coal mining area in NSW Australia.

Jan 1, 2007

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992

By G. Gillet

The conventional magnetic separators used in the mineral industry are equipped with traditional magnetic circuits or with permanent magnets (rare earth). However, when processing minerals with low magnetic susceptibilities or minerals of very small particle size, these separators are inefficient. In addition, a conventional magnetic circuit consumes considerable amounts of electricity to generate a relatively low magnetic field (~2 Tesla). The equipment is also heavy and bulky. Only a separator having a superconducting sole-noid can contribute in solving most of the problems, and only such a separator can produce high magnetic fields with low energy consumption. New developments and the experience acquired in using these superconducting magnets have resulted in new uses for magnetic separation, especially in the environmental area. This paper presents and describes a separation system that uses superconducting magnets that are completely automated and able to treat raw materials (concentration or purification) or liquid industrial effluents containing heavy metals in solution. Several industrial sectors, including the surface treatment, petroleum and chemical industries, are generating effluents containing heavy metal ions. The main metal ions found in such effluents include zinc, copper and vanadium. The purification of such effluents by magnetic separation is performed by adding a certain proportion of iron salts. The treated effluent passes through a superconducting separator where the flocs are retained in a matrix of steel wires. The efficiency of supraconducting high-gradient magnetic separation (HGMS) by this method exceeds 95%. Mineral separation and industrial-waste purification results are presented.

Jan 1, 2000