Search Documents

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By James E. Lawver

At the present time, the Florida phosphate industry is experiencing one of the worst marked slumps in its one hundred year history. Recent agriculture over-production has caused low grain prices such that the net income of U.S. farmers is expected to drop to its lowest level since the 1932 depression. The farmers' low income, along with high interest rates that preclude them from borrowing to purchase fertilizer, make the immediate U.S. phosphate market outlook bleek at best. The export outlook is also pessimistic due to world recession and the U.S. dollar's high exchange rate. In June, 26% of the phosphate industry's workers were laid off for an indefinite period of time. Despite the immediate painful slump, the long-term outlook for the industry looks good. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal and land reclamation.

Jan 1, 1983

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By S. E. Restrepo

To innovate and make the operation sustainable it is necessary to identify the externalities and impacts completely. This paper presents the results of a proposed methodology to make circular economy initiatives viable in mining operations using these aspects: • Economic, safety, and environmental (HSE) risk analysis • Technology observation • Mineralogical characterization • Identification of potential waste uses • Use of government economic benefits The results of the project can be summarized as follows: • Implementation of new technologies in the aggregates process, • efficient use of water, • the valorization of waste to convert it into a by-product, • and access to tax benefits for investment savings.

Mar 2, 2022

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By Robert P. Larkin

The necessity for mineral extraction and its impact on man and the natural environment is a subject of increasing concern to Americans. Rising living standards and new demands for energy require increased mineral extraction, whereas the "new environmentalism" and concern over social well-being warn of the dangers to both the environment and the social system. This dilemma can only be solved by a complete understanding and analysis of all the factors relevant to human welfare which include environmental considerations, economic implications, and the social and psychological dimensions. A decision-making framework is therefore necessary which will encompass all relevant views of the problem.

Jan 1, 1975

By Ernest N. Wolff

You here are all familar with the myriad of new laws, some enacted and some pending, that affect the mining industry. These laws, for example those dealing with suspended matter, affect us in Alaska as they do you. Likewise, our friends in government, the Geological Survey and the Bureau of Mines, provide us with the same fine services that they do elsewhere. I am not going to speak today about these, but concentrate on one act of Washington, D.C. the impact of which is felt, for now at least, principally in Alaska. A little more than a year ago, I spoke in Spokane on the subject, "Governmental Challenge to Mineral Development in Alaska." I outlined some of the policies of Government which were operating to change the rules under which the industry operates and to alter the relation- ship between government, industry, and the individual. At that time the Native Claims Settlement Act had not been passed, but was on the verge of being so. In reading over what I said in Spokane, I note that I touched on many points where Government was actually challenging mineral development in Alaska. With the passage of the Alaska Native Claims Settlement Act, many of these actions were given a cloak of legality, and machinery was set up to concentrate the drive to tie up the public domain, machinery which will allow govern- mental control and interference with the actions of individuals on something like 90% of Alaska's land surface. This remarkable law is going to affect each and every one of you. Now, a year after its passage, we are only just beginning to see its lesson for the future. It was created by a coalition of powerful groups, who got other groups to support them by promising to deliver something they had no intention of delivering. Alaskan issues are again being used to get various groups not to oppose legislation which will severely harm them. It will help to understand the nature of this new drive if we understand the Native Claims Act and how it came into being.

Jan 1, 1973

By John D. Price

The solution to the problem expressed in the title of this paper might well be condensed into one word, AUTOMATON, But if I were to stop there, even though most of you might applaud, I am afraid that a one-word paper might not justify my coming to this meeting, So let?s explore the matter and try to learn if and to what extent the science of automaton can be applied to the problem of coal cleaning. In taking this approach we must, of course, by-pass the fact that plants In this Country and aborad have been automated to a greater or lesser extent. We will explore the matter from the beginning and not merely take the approach that because others have done it we can do it also. First, let us see just what is meant by automaton.

Jan 1, 1959

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By M. S. Safarzadeh

Cu-As feedstocks are among the most problematic copper sources that have been avoided over the past years. The high arsenic content of such ores/concentrates combined with their refractory nature have directed the metallurgical industry towards developing efficient technologies for the treatment of high-arsenic copper ores/concentrates. As the most important member of Cu-As-S mineral system, enargite (Cu3AsS4) is frequently encountered in some of the important copper deposits. Several hydrometallurgical and pyrometallurgical processes have been examined for the treatment of enargite concentrates, but currently, no commercial operation exists. In an effort to develop an original processing option, an acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2?4H2O, PbSO4 and Cu0.47Fe0.53SO4?H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 h with a sulfuric acid to concentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena, and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different levels. The purpose of this paper is to evaluate phase transformations during the acid bake-leach process for the treatment of an enargite concentrate, and to study the effect of sulfuric acid dosage on the extraction of Cu, Fe, and As. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.

Feb 23, 2014

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By Frank J. Klima

Explosives are probably the most widely used and most mysterious large scale&apos; mining tools of modern times. The post black powder explosives were primarily nitroglycerin-based straight dynamites, ammonia dynamites, blasting gelatin, gelatin dynamites, ammonia gelatin dynamites, etc. Of these, the strongest and highest velocity explosive used in industrial operations is blasting gelatin, which is nitroglycerin colloided with a nitrocellulose of medium nitrogen content in proportions which give the product a plastic character, or about 93 to 7. Many variations of the basic groups above were developed by substituting ammonium nitrate and/or sodium nitrate for some of the nitroglycerin. The nitrates being insensitive to caps required a certain percentage of nitroglycerin to sustain detonation in smaller quantities or diameters. Paralleling the development of industrial dynamites was the development of more expensive, highly sophisticated explosives which were developed for specific military purposes. Such explosives as Amatol, RDX, Composition A, Composition B, Composition C, Lead Azide, PETN (Pentaerythritol Tetranitrate), Tetryl, Pentolite, TNT, etc., were primarily military explosives. Amatol, which is a cast mixture of ammonium nitrate and TNT (Trinitrotoluene), and identified by percentage of AN versus TNT as 50-50 Amatol, 80-20 Amatol, etc., was a favorite World War I explosive. RDX, or Cyclonite, was widely used in World War II. Also used during WW II were compositions A. B, and C, which were mixtures of RDX (Cyclotrimethylene trinitramine), TNT, and other nitrotoluenes. These high explosives, along with nitroglycerine, are exact chemical compositions or mixtures of exact chemical compositions which are individually explosive, or in other words, individually capable of explosive chemical decomposition when properly initiated. These chemical decompositions result in the formation of simpler compounds and/or large quantities of common combustion gases, and large amounts of energy in the form of heat. Of these, the most powerful is RDX which, based on the ballistic mortor test, is 1.5 times as powerful as TNT. Chemically, the decomposition of TNT releases about as much energy as the reaction of ammonium nitrate and fuel oil.

Jan 1, 1967

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021