Search Documents

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By A. A. Compoli

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No.3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No.3 Coalbed.

Jan 1, 1995

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016

By T. E. Scartaccini

A drill recorder is a permanent data collecting instrument. In open pit blast hole drilling the application of a drill recorder is that of data collection, drilling control, and drilling education. The various drilling parameters (weight, RPM, penetration, torque, and air) have a drilling correlation which can be demonstrated and documented by a recorder graph. When the correlation is physically put to use during the process of drilling, then the recorder has become a drilling tool and is no longer just a data collecting instrument, per se. By being able to maintain accurate records and drilling control, comprehensive studies of changes both operational and technological can be made. These are based on in-progress facts and not after-the-fact logs. To determine total drilling efficiency, drilling conditions must be documented and controlled. Field operations at American Smelting and Refining Company's Mission Mine have proved that by increasing drilling control, demonstration of parameter relationships, and drill monitoring, more economic efficiency can be obtained. In comparing results obtained with recorder control and conventional control a decrease of 14 percent to 36 percent of drill footage costs were obtained. The percentage of variance is dependent upon whether drilling is milled-tooth or carbide-insert bit drilling.

Jan 1, 1970

By Luke Clarkson, David Williams

The intent of this paper is to provide overview context to allow broader understanding of conventional tailings dam failure mechanisms. The research leverages global knowledge, experience, and data collection and interpretation for the safe and controlled management of the geotechnical stability of a tailings storage facility. The motivation for this review is to facilitate transparent access to tailings dam background and understanding. This paper addresses the core understanding of geotechnical failure mechanisms, and how these eventuate to instability and failure of tailings dam structures. This research focuses on foundation failure, internal erosion and piping, overtopping, seepage, seismicity, and slope instability and provides insight into what factors contribute to failure, how failure progresses due to such failure, anticipating and monitoring for the aforementioned failure modes, and designing to mitigate their risk.

Feb 15, 2021

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By Alvin D. Cronberg

Silica flotation with amine salts has been a commercial process for years in certain non-sulfide mineral systems. Phosphate rock and feldspar deposits are notable examples. Generally, the quartz is clean and coarse. Primary amines and imidazolines are used, usually in a mole weight range 250-300, ad often fairly impure grades of collectors are satisfactory. As the production of magnetic iron concentrates grew in Michigan, Minnesota, Canada and in foreign locations, the iron mining companies began to explore amine flotation of silica to improve these concentrates. Many of the mining companies, as well as reagent suppliers, government laboratories and university research teams, had already studied amine collectors for silica, but the application to magnetic iron concentrates presented a real commercial opportunity to apply the art. Amine flotation of silica has been accomplished by simple addition of a flotation cell, and possibly a regrind mill, at the end of the magnetic concentration process. The flotation system gave the mill operator a flexible method to control final grade caused by ore variations in the feed. It increased iron content with lower silica, which resulted in lower freight costs per unit Fe and better pellets for blast furnace use.

Jan 1, 1968

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By Chris Howell

PotashCorp?s Aurora phosphate mine, in Beaufort County, NC, operates four low pressure boilers and four high pressure boilers to meet its process steam requirements. Maintaining these boilers is critical to meeting production demands. Processing phosphate ore into phosphoric acid requires large amounts of sulfuric acid and steam. Ore is mined from the phosphate deposit with large bucket excavators after 9 to 30 m (30 to 100 ft) of overburden is removed. The phosphate ore is mixed with water to make a slurry that is pumped to the mill. Elemental sulfur is burned in the presence of air to make sulfuric acid. This process is highly exothermic and boilers produce steam while cooling the process. The phosphate ore is reacted with sulfuric acid and the resulting products are refined into different grades of phosphoric acid for fertilizers, feed stock and food additives. Plant operators at the mine were challenged with boiler feed water that was high in silica and other contaminants. As a result, boiler operations were experiencing difficult, labor-intensive operations and equipment deterioration. This resulted in higher operating costs and diminished processing performance. The facility was operating an aged boiler feedwater pretreatment system that included warm lime softening followed by pressure filtration and a cation/anion/mixed bed demineralizer system. The demineralizer required frequent regeneration and chemical usage was high and costs were difficult to predict. Depressurized well water (DPW water), used for plant utility water and boiler makeup, is very high in silica, in the range of 60-70 ppm. Silica can form scale at pressures below 600 psig. Above 600 psig, silica starts to volatize, carrying over with steam to potentially form deposits on downstream equipment and processes. Mine officials decided to upgrade the boiler feedwater pretreatment system to a state-of-the-art reverse osmosis (RO) membrane system. This new system, which started up in March 2009, has improved operating performance and reduced water consumption and overall operating expenditures.

Jan 1, 2011

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964