Search Documents

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The U.S. National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two-phase implementation of an IoT-based intelligent machine monitoring system.

By Heather Wright

Shovel operators are one step closer to having a better tool to operate and monitor their equipment. The development of a unified shovel interface is proceeding into phase three, focused on producing a standard application programming interface (API) for connecting onboard devices. This solution will positively impact safety, performance and productivity, and is the result of collaborative work driven by the Global Mining Standards and Guidelines Group (GMSG). Proof of concept revealed During the spring of 2013, Peck Tech Consulting was engaged to develop the working proof of concept (POC) software implementation, which integrates multiple vendors? systems into a single interface using one-to-two displays. As a result, the GMSG developed a functioning, manipulatable, unified shovel interface proof of concept and unveiled it at the World Mining Conference in August in Montreal. The proof of concept effectively provides a unified operator interface that pulls together the many divergent systems onboard large shovels.

Mar 1, 2014

By Norman F. Schulz

Representative sample s of typical manganiferous iron ores from the Cuyuna Range, Minnesota, were reduced to the metallic iron state at temperatures just short of fusion with an excess of coke in the manner prescribed by the R-N Direct Reduction Process. The magnetic separation characteristics of the reduced ores were determined at several grinds by means of the Davis magnetic tube concentrator. The efficiency of metallic iron concentration by magnetic separation was a direct function of the degree of metallization of the ore sample and of the degree of liberation attained in grinding. Some improvement of liberation characteristics was observed if a small amount of sodium chloride was present in the ore during reduction. Despite the extremely fine -grained structure of the crude ores, iron concentrates containing more than 90% Fe at iron unit recoveries of 90% or more were obtained from well-metallized samples of three of the four ores tested. The rejection of manganese to the tailings corresponding to such separations varied from 80 to 95%.

Jan 1, 1967

By M. Nambiar

Due to the remote locations of mining projects and the need for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short-circuit capacity. To cope with this situation, more and more mining operators are considering the installation of appropriately designed synchronous condensers together with power factor correction and harmonic filter systems (PFC & HFS). The installation of such power quality equipment is viewed as a technological advancement in the mining application. An adequate level of short-circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter-driven gearless mill drive systems (GMDs) used for grinding. This paper explores the impact, technical advantage and reasoning for the selection of this advanced hybrid technology to cope with the power system challenges of future mining projects. It also delves into the potential problems and how to address them.

By Craig Bournes, David Chapman, Michael DiPonio

Historically, boulders are a frequent source of problems in soft ground tunneling. During tunnel construction, the need to manually break and remove boulders as obstructions causes delays to the project. Repairs to a tunnel boring machine (TBM) can also be a source of delays. Managing these problems is difficult since normal soil investigation techniques do not accurately predict the presence or frequency of boulders. This has lead to considerable number of claims for extra costs and delays during the construction of soft ground tunneling projects. These issues are exacerbated in pressurized face tunneling systems where there is limited access to the TBM cutterhead for obstruction removal and/or cutterhead maintenance. The project team that built the Big Walnut Augmentation/Rickenbacker Interceptor (BWARI) Project for the City of Columbus successfully managed the design and construction of a 4,267 mm (14 ft) diameter soft ground tunnel with high boulder concentrations in a complex geologic setting. The management of the boulder issue tookplace during several phases of the project.

Jan 1, 2007

By W. K. Pincock

Accident prevention can be portrayed as a science that deals with facts and natural phenomena and must be dealt with in the same manner as any other operating problem. Safety at the Copper Queen Branch dates back to 1913 when a Safety Organization was started and rules formulated for underground mining. Since then the mining industry has made substantial progress in the elimination of accidents and when the Lavender Pit was started in 1951, it adopted the general plan in use at all Phelps Dodge properties. Following is a brief description of the Pit Operations:

Jan 1, 1959

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By Christian F. Baiz

Industrial minerals can have similar financing requirements to those needs of metaliferrous and coal mining projects. Although, one may see many similarities in the fundamentals of the various risks that must be evaluated in lending to any specific project, one of the outstanding differences is the understanding of the many different markets that these industrial minerals represent. There are in excess of 30 principal industrial minerals ranging in terms of annual production from the largest quantity such as sand and gravel, to possibly the smallest quantity of production of a legitimate industrial mineral which may be defined as industrial and rough gem diamond. If we assume that it is necessary to finance independent projects of ore bodies of industrial minerals for development, the financing techniques are similar to the fundamentals that we would use for financing coal projects or metaliferrous deposits. Therefore, let's begin by redefining project financing in the traditional banking or private sector area, and then in the later development of this paper, we will apply these techniques to industrial minerals in general and cite it with several specific examples.

Jan 1, 1982

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By K. A. Sauer

Blasting can create severe interference for a mine's carbon monoxide based fire detection system. At the present time, without being able to differentiate between blast and non-blast carbon monoxide, a fire detection system must either set fairly high alarm levels for its sensors, or allow frequent "false" alarms to sound during blasting. This paper will introduce current work being done which will attempt to define characteristics of the carbon monoxide concentrations time curve for blasting. The work uses drift blasting for its data base as it is one of the more common forms of blasting. Future work with the data may produce a mathematical model which can be used to monitor and identify the carbon monoxide time curve for drift blasting.

Jan 1, 1989

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By L. E. Murr

Solution flow in leach dumps and heaps or in columns of representative rock has been the subject of only limited studies. This is a regime involving unsaturated flow in semiconsolidated rock with a wide size distribution. Even the concepts of continuous flow systems are fairly recent, and have evolved from the search for better methods of operating industrial chemical reactors. (1-3) Waste rock consolidation and permeability play a key role in solution flow characteristics. Harris (4) suggested that bulk density variations in a leach dump could alter the particle-to-particle contact, and that large particle aggregates could act like single, large particles . In the limiting case where the bulk density approaches that of the undisturbed, consolidated rock, the entire waste unit would behave as a single particle. Roman (5) treated the phenomenon of bulk density and its effect on consolidation in terms of lixiviant flow paths or solution channeling in leach dumps. Like Harris, he assumed that no solution moved through particles or particle aggregates associated with zones of high bulk density. Solution flow paths are thus effectively separated by particle regimes, creating solution channels in the waste body. While some attempts have been made to describe solution flow in leach dumps and related systems by utilizing computer model approaches and laboratory- scale simulations (5,6), there have been no direct, large-scale observations of solution movement in channels or of the actual channel sizes and distributions within a waste body. This paper describes a series of experiments involving large-scale, controlled waste leaching tests, conducted over a period of several years, and aimed at providing some direct observation of the changes in waste consolidation and permeability, the size and distribution of solution channels, the movement of such channels with continued solution application, and other features relating to solution flow during the leaching of low-grade waste. These results are then combined with mineralogical information to explain observed leach behavior.

Jan 1, 1981

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982