Search Documents

By T. J. Fenner

Research conducted in South African mines has demonstrated the benefit of ground penetrating radar for the detection of geologic features and hazards. This is crucial for safety and production considerations in underground mines that are as much as 4 kilometers deep. This paper describes a new ground penetrating radar system designed specifically for high quality data acquisition, in the harsh conditions of deep underground environments, for use by operators with minimal geophysical experience. Design criteria included automated functions, intrinsic safety, light weight and minimal power requirements. Data is processed on the ground surface by geoscientists using a PC.

Jan 1, 1994

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By Gunjan R. Bhattarai, Kumar Bhattarai

Recently, there has been an enormous increase of interest in artificial intelligence (AI), machine learning (ML), and their applications by researchers, government agencies, and the underground construction industry. Ultimately, these tools have the potential to automate the design and construction processes and boost productivity, safety, quality, and operational stability. This paper presents ongoing research and applications of artificial neural networks (ANNs), robotics, and 3D technologies in ground characterization, tunnel ground support prediction, risk projection and reduction, and productivity enhancement in TBM operations. The paper further investigates potential uses of AI, robotics, and 3D technologies in the underground construction industry

Dec 1, 2022

By William H. Dresher

World trade has increased significantly during the last quarter century. However, a new rational for protectionism is emerging which argues for the restriction of trade as a means of preserving and protecting the environment. Fearing lower environmental standards in the Third World, environmentalists are calling for new trade barriers between the developed countries and the developing countries to combat what they see as "eco-dumping." The "greening" of protectionism and the merging of environmental standards into international trade agreements could fundamentally change the world trading system as well as seriously impact the availability of raw materials to provide for the needs of the peoples in both the developing and the developed worlds. This discussion will deal with the agreements and regulations that promise to influence the trans boundary shipment and recycling of scrap metals and wastes containing metals and their projected impact on world trade and metal prices. Emphasis will be placed on the Base1 Convention, whose restrictions concerning trans boundary shipment of scrap metal and metal-containing wastes for recycling took effect on December 31, 1997.

Jan 1, 1998

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By Michael Markels

The United States Environmental Protection Agency (EPA) is charged under the Federal Water Pollution Control Act Amendments of 1972 with establishing effluent limitations which must be achieved by point sources of discharge into the navigable water of the United States. Section 301 (b) of the Act requires the achievement by not later than July 1, 1977, of effluent limitations for point sources, other than publicly owned treatment works, which are based on the application of the best practicable control technology currently available as defined by the Administrator pursuant to Section 304(b) of the Act. Section 301(b) also requires the achievement by not later than July 1, 1983, of effluent limitations for point sources, other than publicly owned treatment works which are based on the application of the best available technology economically achievable which will result in reasonable further progress toward the national goal of eliminating the discharge of all pollutants, as determined in accordance with regulations issued by the Administrator pursuant to Section 304(b) to the Act. Section 306 of the Act requires the achievement by new sources of a Federal standard of performance providing for the control of the discharge of pollutants which reflects the greatest degree of effluent reduction which the Administrator determines to be achievable through the application of the best available demonstrated control technology, processes, operating methods, or other alternatives, including, where practicable, a standard permitting no discharge of pollutants.

Jan 1, 1975

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By R. Venkataramani

Crushed stone operations have become more difficult due to rising costs of labor and equipment, with the consequent reduction in profit margins. Competition from other operators and the encroachment of vertically integrated companies place severe restrictions on available markets. The seasonal demand for stone precludes any definite production level, and changes in productivity have to be accommodated. These influence profitability, and therefore production plans must be continuously adjusted to keep pace with rapidly changing conditions. The basic problem of stone companies seeking to maximize profits is one of balancing stone production costs, costs of inventory holding and stock-piling, marketing costs and any other charges accruing over time against the selling price of stone. Because of high peak demands, slack period production must be stored and then distributed to supplement peak period production. For a multi-plant operation, there is a need to evaluate at the same time the interaction between the plants and the various marketing sectors. In a multi-plant operation with different production capacities and production costs, stone producers are interested in the answers to the following questions: 1. How much stone should be produced at each plant in each time period? 2. What should be the optimum stone shipment from each plant to each market? 3. What are the effects on net returns and shipping plans, if production capacities are altered at the plants? These questions have many different answers that, will satisfy demands. From the point of production scheduling, the minimum production cost may be the objective. From the inventory standpoint, the best solution will be to synchronize production with sales. However, when the transportation of stone is also considered, the desired end is to achieve that delivered cost which maximizes the company f s net return. Besides, only an extremely naive analysis ,wouId attempt to

Jan 1, 1971

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

The objective of this paper is, firstly, to summarize several field developments utilizing the art of hydraulic fracturing as it has been extended into various mining applications. Secondly, to summarize the understanding of the hydraulic fracturing processes; and lastly to discuss researchable areas and possible future applications. Hydraulic fracturing was developed as a method of stimulating production of oil from oil producing formations. The primary paper by Clark (1) in 1949, describes the process of placing a hydrostatic pressure of sufficient strength on the producing formation of an oil well that the rock apparently cracked, and then, on allowing the well to flow back, a higher rate of recovery of oil was enjoyed. The interpretation of the process mechanism was that the formation rock was cracked to a considerable distance from the well bore, increasing the drainage area; thus, the productivity of the well was measurably improved. Figure 1 is illustrative of this process. This development was of major significance to the oil producing community and considerable research and development ensued. Improvements in method, engineering development of equipment, and research to ascertain the optimum application of fracturing practice led to a highly sophisticated, but specialized technology. The Production Research Division, Continental Oil Company, vigorously pursued research in this area in the 1950's with a resulting number of process improve¬ments. The research group, published a significant number of technical papers on these various researches. One of the developments was the process aimed at controlled orientation of the fractures, either in the vertical (2) or horizontal (3) orientation.

Jan 1, 1969

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

By Éder Domingos Oliveira, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

The purity of rare earth products depends on the ability of the reagents used to selectively promote the precipitation of the rare earth elements (REE) from impurities present in sulfuric liquors. The present study aims at investigating the conditions required to precipitate REE, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with a low Al3+ and UO2 2+ and a very high Ca2+, Mg2+, Mn2+, and SO4 2− impurity content. The rare earth sulfuric liquor was obtained in a previous study by the reaction of a rare earth ore with sulfuric acid, pyrolysis at 700 °C/2 h, cooling at 20 °C, and water leaching. The impurities such as Fe3+, Th4+, and PO4 3− were completely removed from the liquor in two consecutive neutralization steps. In order to recover the REE, the purified rare earth liquor was then treated with oxalic acid and sodium carbonate. Rare earth oxides (REO) precipitated with oxalic acid displayed a very high purity (99.2% w/w) and low impurity content. In contrast, the rare earth carbonates precipitated with sodium carbonate presented a comparatively lower REO content (68.5% w/w) and 94.2% of purity, but with a higher content of impurities. Better precipitating conditions were achieved at 60 °C, compared with 20 °C, and under stoichiometric reagent consumption, with REE precipitation efficiencies higher than 96%. The dosage above the stoichiometric condition caused the precipitation of calcium oxalates and co-precipitation of rare earth sulfates when oxalic acid is used, and precipitation of calcium, manganese, and uranium carbonates and also a co-precipitation of rare earth sulfate when sodium carbonate were used. An integrated flowsheet to produce a high-quality rare earth product from rare earth sulfuric liquor containing some impurities is proposed.