Search Documents

By James R. Boulton

Fire detection using Carbon Monoxide sensors is based on the assumption that a rise in the level of Carbon Monoxide in the atmosphere over a fixed, predetermined ambient level is indicative of a fire. The method is simple, reliable, and effective in those mines where the only source of CO is from undesired combustion. Ambience for this purpose is defined as that level of the gas that is present on a day to day basis whose source is not a fire. In a diesel powered mine the level of CO can and does vary so widely from hour to hour and minute to minute that the selection of a predetermined, fixed level represents a compromise between sensitivity and reliability. The compromise is a best of both and worst of both situations and the computer system often resembles the little boy who cried wolf instead of a state of the art early fire monitoring and detection system. Cyprus Coal personnel have developed method of determining the ambient level of CO in the atmosphere on a real time basis and using that dynamic ambient level to determine whether or not a fire exists in the mine. The method has been given the name of Wave Trend Crossing.

Jan 1, 1991

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By Claude M. Moreland

It is common practice when thermally drying coal from wet coal preparation facilities that the coarse +0.5mm fractions and fine fractions (-0.5mm) are combined and fed to a thermal dryer. There are very good reasons for this concept. The coal feed is much easier to handle in this condition for it is not as likely to stick inside the dryer or hang up in the material handling equipment, and is easier to feed and discharge. However, it is generally only the -0.5mm fines that really need to be dried. The +9.5m fraction of the cleaned coal will leave the dewatering screens, or drain and rinse screens, at an acceptable surface moisture, probably 5 or 5 ½ percent. The 9.5m x 0.5mm mesh fraction can be centrifuged to about 8 percent. The -0.5m fines can range from 18 to 22 percent or more, depending upon the type of equipment employed to dewater, and upon the size distribution within this size range.

Jan 1, 1982

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By J. C. Motz

With ore grades continually decreasing and finer mill feed requirements, it becomes increasingly important to have the capability to handle the larger tonnages economically. With the 10 ft. Standard capable of reducing 1,633 metric tons per hour (1,800 short tons per hour) to 80 percent passing 50 MM (2 inches) and the 10 ft. Short Head following to produce a mill feed of all minus 12 MM (1/2 inch) at a rate of 608 metric tons per hour (670 short tons per hour), we feel significant savings will be realized in installation and operating costs. The largest concentration of cost in the secondary and tertiary crushing stations is the building itself that houses the process equipment. An example of the savings to be attained can be seen from an examination of a 40,820 metric ton (45,000 short ton) per day crushing plant. A total of nine 7 ft. Symons Cone crushers is used to generate 12 MM (1/2 inch) ball mill feed. The average center distance between units is 6.1 M (20 feet) and allowing a 6.1 M (20 feet) nominal distance from the centerline to the wails, the building becomes 61 M (200 feet) long. For this production rate, four 10 ft. Symons Cone crushers would be required. With the 10 ft. crushing plant requiring a center distance spacing of 7.6 M (25 feet), the building length totals approximately 38 M (125 feet). Construction costs vary depending on location, but a reduction in building length from 61 M (200 feet) to 38 M (125 feet) will result in estimated savings of between $2,500,000 and S4,000,000. While the 10 ft. Symons Cone has been involved in a number of feasibility studies for some time, the Process Machinery Division of Rexnord commenced detail design work on the 10 ft. Cone crusher in 1972. For comparison purposes, the 10 ft. and 7 ft. capacities are given in Table 1.

Jan 1, 1978

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

Though the mining industry is beset with problems-a broad slump in metal prices, a rash of acquisitions and takeover attempts, rising capital costs, and an aggressive Canadian energy program-there was an under-current of optimism at the 1981 AMC conference that's been missing at industry meetings in recent years. The industry anticipates a turnaround in the 1980s, buoyed perhaps by the new spirit of cooperation from the Reagan administration. For the first time in years, it appears that Washington and the mining industry share mutual goals for developing the nation's resources. A number of prominent Reagan officials were on hand during the three-day conference in Denver, September 28-30, to reassure conferees that restrictions plaguing energy and minerals development would be eased. Interior Secretary James Watt and other government speakers promised cooperation in bringing balance to federal public lands policies, a review of regulations that have hampered the industry, and prompt action on domestic minerals policy. Daniel N. Miller, Jr., assistant interior secretary for energy and minerals, said, "It is our intent to dismantle the overhearing bureaucracy that has stifled mineral and energy exploration. We know that Interior's rules have shackled the mining industry in recent years, and we know that those rules must be eased." Miller noted that the administration will not permit mining on national park lands or wildlife refuges, but added that "we must assess a variety of uses of public lands ... we will restore lands to multiple use where practical." EPA administrator Anne Gorsuch assured industry representatives that the administration intends to work within environmental laws and with Congress to review and revise water, soil, and air pollution policies. "We have a strong commitment to see that there are major mid-course corrections" of air regulations, Gorsuch said. Support from these "new friends in Washington" will be crucial in light of the serious problems pressuring the industry. Copper prices have plunged to almost three-year lows and prices for molybdenum, gold, and silver have slumped. Earnings are down and today's high interest rates prevent a quick turnaround. Companies are on edge after the recent takeovers of Kennecott, St. Joe Minerals, and Texasgulf Though the companies may benefit from the major injection of capital that large energy firms can provide, many observers fear the new parent companies won't be willing or able to survive the cyclical metal markets. Arco and Gulf Resources, for example, have been criticized for closing Anaconda's Montana copper facility and the Bunker Hill unit in Idaho, respectively. Canada's national energy program has brought additional pressure on the industry. This policy, which emphasizes Canadian majority ownership of the country's energy sources, resulted in acquisition of Texasgulf's Kidd Creek lead-zinc-silver complex by Canadian and French interests. In response, the American Mining Congress adopted two resolutions on takeovers. One calls for the US government to review laws regulating tender offers and takeovers "to better ensure that principles of fairness and sound investment policy govern such transactions.'' The other asks the government to demand "fairness and reciprocity" as a basis for US policy governing international trade in minerals and investment relations with other countries. AMC's shopping list included four other priority goals, aimed primarily at the Interior Department: • Prompt implementation of Interior's efforts to bring order and balance to rules governing access to public lands for exploration and development. • Statement by the President of a comprehensive and coherent domestic minerals policy. • Amendment of the Clean Air Act to remove impediments to productivity and barriers to economic development that are not necessary to essential goals of the act. • Development of new approaches to better achieve worker health and safety in the most cost-effective manner without penalizing productivity. Almost 6000 mining industry executives attended the 1981 convention-the largest in AMC's 84-year history. As in years past, the conference offered a wide spectrum of presentations-nearly 100 papers in 26 sessions-ranging from commodity forecasts to the latest technical achievements. New Administration Stockpile Goals The minerals availability session included a presentation on management of the minerals stockpile by Paul K. Kruege r of the Federal Emergency Management Agency. Krueger notes that rather than providing incentives for development of a domestic raw materials industry, the government has "a history of providing disincentives to industry." In mining industries, he adds, the rate of productivity growth has been -6% over the last six or seven years. Krueger feels there will be a major change under the Reagan administration. In March 1981, FEMA began the first purchase program for the national defense stockpile in over 20 years. The stockpile is sadly out of balance, Krueger adds. Stockpile materials are

Jan 12, 1981

By C. L. Karr

Establishing suitable control of pH, a requirement in a number of mineral and chemical industries, poses a difficult problem because of inherent nonlinearities and frequently changing process dynamics. Researchers at the U.S. Bureau of Mines have developed a technique for effectively controlling such systems. This technique successfully combines the process control capabilities of fuzzy logic and the search capabilities of genetic algorithms. Fuzzy logic offers an effective mechanism for handling nonlinearities, while genetic algorithms can provide fuzzy logic controllers with real-time adaptive capabilities. This Bureau-developed technique is applied to a laboratory acid-base neutralization experiment. Nonlinearities in the laboratory system are associated with the logarithmic pH scale and the changing process dynamics are due to alterations in pH and buffering capacity input solutions. Results indicate fuzzy logic controllers augmented with genetic algorithms offer a powerful alternative to conventional process control techniques in such nonlinear, rapidly changing systems.

Jan 1, 1992

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By Archie M. Richardson, Carl E. Brechtel, Tom R. Kelly, Frank Feero

Recent work to upgrade the ventilation system for the el Mochito lead/zinc mine in central Honduras is discussed. Network modeling and underground measurements were used to evaluate cost-effective alternatives for achieving satisfactory ventilation in a complex and expanding underground operation. Both interim and long-term solutions were implemented to make mining possible under difficult conditions. INTRODUCTION Mining operations at the el Mochito Mine, located in the central highlands of Honduras, Central America, have been virtually continuous since the opening of the mine in 1948. Initially a high-grade silver mine, the mine has expanded along a westward trend of pipe-like orebodies to a distance of roughly one mile from two centrally located shafts. Production of the relatively large San Juan orebody at the western most extension of the mine (Paddock, 1981) led to the introduction of diesel-powered equipment; however, the ventilation infrastructure was insufficient to meet the needs of mechanized mining. A succession of owners/operators in the 1980s allowed the existing ventilation infrastructure to decay to the point that ventilation in the production areas of the mine was very poor. Environmental conditions in some working areas were not conducive to efficient ore extraction because of high dry bulb temperature, high humidity, and diesel emissions. Upon acquiring the mine in 1990, Breakwater Resources of Tucson, Arizona began an aggressive program to refurbish the mine infrastructure to complete extraction of the San Juan orebody and to allow the extension of the mine another 2500 ft to the west for extraction of the Nacional orebody. The program included increasing the capacity of the main ventilation system. This article presents a case history of the process of upgrading the ventilation system in a mine where extensive old workings cause large air leakage. This process has been one of selecting solutions to difficult technical problems that are compatible with the existing mine infrastructure and economic constraints. The initial ventilation system is described in the background section, along with ventilation projections for the mine expansion. Field characterization of the ventilation system for design verification and fan specification is then discussed. The paper describes a series of interim changes to the system to improve ventilation pending completion of new ventilation boreholes. In addition, the temperature/ heat problems in the mine are described. BACKGROUND Initial Condition of Ventilation System The ventilation system is illustrated in Figure 1, which shows the extent of mining with the main ventilation paths superimposed. Early mining around the two shafts opened up vertical connections (stopes and raises) over the entire 2420 ft (737.6 m) of vertical extent, and mining progressed to the west primarily using compressed air and electric-powered equipment. Since ventilation was not a complex problem in the original mining system, the stopes and interconnecting raises were not sealed. The San Juan orebody was much larger than the silver ore zones mined previously, being primarily zinc and other base metals. Its geometry, size, and grade allowed the use of vertical crater retreat (VCR) stoping with diesel mucking and haulage equipment. Its depth, along with the existence of warm groundwater, resulted in a mine climate problem on the lower levels. To establish a complete ventilation circuit, two vertical boreholes (Bonanza Nos. 1 and 2) had been drilled by previous owners from the surface in the vicinity of the San Juan orebody. The system design called for air to be drawn down the intake shafts, across the lower mine levels to the San Juan workings, then up through the San Juan ramps and ore passes to these two exhaust boreholes (see Figure 1). In practice, however, only the Bonanza No. 1 borehole was drawing air through the desired path. Leakage across the old upper levels from the intake shafts, the Caliche tunnel, and from intervening abandoned stopes and raises supplied most of the air flowing to the base of the Bonanza No. 2 borehole. In effect, there were two ventilation circuits in semi-parallel through the mine, of which only one was delivering appreciable air to the San Juan workings.

Jan 1, 1993

By Julian Brown, Steve Hicks, Zach Agioutantis, Zachary Wedding

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970

By Kelly F. Bailey

Introduction On June 20, 1986, the Occupational Safety and Health Administration (OSHA) published revised asbestos exposure standards for general industry and construction. The standards reflect OSHA's attempt to adequately control workplace exposures to minerals it considers carcinogenic - minerals capable of causing or contributing to cancer. These standards specifically identify asbestos as: chrysotile, an asbestiform serpentine mineral; and the amphibole minerals amosite, crocidolite, tremolite asbestos, actinolite asbestos, and anthophyllite asbestos. Each of these has a more common nonasbestos mineral analog that exists in nature in a crystalline, blocky shape rather than the hair-like or fibrous shape of asbestos. The mineralogical names for three of these nonasbestos minerals are unique: antigorite for chrysotile, cummingtonite-grunerite for amosite, and riebeckite for crocidolite. The other three nonasbestos analogs do not have unique mineralogical names. They are simply designated as actinolite, tremolite, and anthophyllite without the word asbestos following their names. The 1986 OSHA standards not only cover exposure to the six asbestos minerals, they also cover specifically the nonasbestos forms of actinolite, tremolite, and anthophyllite (AT&A). The new standards regulate these minerals exactly like asbestos (OSHA, 1986). The construction aggregate industry views this as a major problem because these nonasbestos minerals are common amphibole rock-forming minerals in the earth's crust. They exist in small quantities over large areas of the United States (Kuryvial et al., 1974). These minerals, unlike asbestos, are not mined for a specific commercial purpose. They are unavoidable components in much of the aggregate used for construction throughout the US. They are also common in the gangue material of metallic ores. There are areas of the US where amphibole-bearing bed¬rock is common. Not every rock mass in these areas contain amphiboles, however. It does mean, though, that amphiboles are physically compatible with many of the rocks in those areas. And given the correct geochemical conditions, they will be present primarily in the nonasbestiform variety. In addition, these amphiboles will probably exist in the natural drainage system, sand and gravel deposits, stream sediments, lake shores, valley basins, or ordinary beach sand within these areas. There has been little quantification of nonasbestiform AT&A in dusts and soils in the US. This is not surprising since these nonasbestiform minerals are not commercially valuable. However, an example of the pervasive nature of these minerals can be found in a 1981 Geological Society of America publication where about 0.7% tremolite-actinolite was found in the desert dust in and around Tempe, AZ (Pewe, 1981). Since OSHA standards treat these common nonasbestos minerals as carcinogens in the same way as asbestos, large natural areas in the US are implicitly being labeled as hazardous by OSHA. When a substance is identified as a carcinogen, another OSHA standard comes into play, the Hazard Communication standard. There are also right-to-know laws in 9 states that essentially duplicate this federal standard. These standards require that a product containing 0.1% or more of an OSHA-designated carcinogen be labeled as such (OSHA, 1983). This means that much of the stone and sand gravel products occurring naturally and mined in the US could be labeled a carcinogen when, in fact, they are not. The National Stone Association (NSA) and the domestic construction and mining industries believe that OSHA has seriously erred. The NSA has studied the health, mineralogical, technical, economic, and legal basis for OSHA's action. These studies concluded that there is no justification for the agency regulating nonasbestos minerals as if they were asbestos. Health issues The preamble to OSHA's 1986 asbestos standard states that evidence for asbestos-like health effects from exposure to nonasbestiform varieties of AT&A is inconclusive (OSHA, 1986). The fact is, not only are the data inconclusive, they are nonexistent. During 1986-1987, NSA's occupational health and epidemiology consultant, Environmental Health Associates (EHA), reviewed all available health studies related to AT&A. EHA found evidence that malignancies in both experimental animals and humans are associated with the asbestos forms of these minerals. No experimental or epidemiological evidence was found that indicated such pathogenic effects occur from exposure to nonasbestiform varieties of these minerals. There are relatively few scientific studies of the health effects of exposure to nonasbestiform varieties of AT&A. In three different animal studies, exposure to either nonasbestiform tremolite or actinolite did not result in pulmonary fibrosis on in excess tu-

Jan 11, 1988

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

By E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality over time. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By Carrie Smith

Mining has historically been one of the most male-dominated industries in the world. From underground operations to executive boardrooms, the presence of women has often been slim. Women had often been excluded from operational, leadership and decision-making roles, both by cultural norms and systemic barriers. According to PwC’s Global Mine Report (2023), women represent around 14 percent of the global mining workforce. Leadership representation, however, remains sparse, with S&P Global’s 2023 report showing women holding approximately 12 percent of C-suite positions and only 3 percent of senior leadership roles globally. These figures reflect persistent gaps, but they also highlight the progress driven by a new generation of women transforming the industry. Despite the gender imbalance among mining workers, women have continuously made grand strides within the industry, resulting in pivotal changes. At the forefront of this transformation is Kimberly Morrison, one of several women who have played pivotal roles in shaping the mining sector.

Aug 1, 2025

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

Through-the-Earth (TTE) communication systems were developed to provide post-accident communication in underground mines. Unlike primary tracking systems, they do not require any major infrastructure installations underground. Instead, they use the Earth’s overburden as the medium or channel for the transmission of electromagnetic waves between surface and underground. Under ideal conditions, TTE communication systems should be able to provide full-duplex, two-way voice, text and data communication. However, this will depend on the design and optimization of the different types of TTE communication systems (that is, antenna and electrodes), and understanding of the rock properties and their influence on the transmission of signals. This can help simulate and model the transmission efficiencies and predict the possible range and data rates. Being able to optimize the performances of these systems can enhance rescue missions, improving the chances of saving trapped miners, and ultimately reduce fatality rates across the mining industry.

Feb 1, 2025