Search Documents

By J. H. Mackey

"Where can I obtain a reclamation bond today?" "Who is writing your bonds?" These questions are common and heard frequently. The fact that the Society of Mining Engineers has determined that two of the five environmental topics reviewed at the 1989 Annual Meeting relate to reclamation bonding indicates to me that those who are involved in the coal industry, no matter what capacity, remain very cognizant of the reclamation bonding dilemma.

Jan 1, 1989

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By S. Kenzap, V. Kazakidis

Risk assessment is an essential component of mine feasibility studies. However, it is often challenging to identify the appropriate analysis and derive the required input data. The uniqueness of a mining project and the associated technical issues require customization of the risk assessment approach to meet both requirements and characteristics. The uncertainty driving the operating risk in mine feasibility studies and its assessment through Monte Carlo simulation as a component of a cash flow analysis are discussed in this paper. The paper introduces the use of the analytic hierarchy process for derivation of qualitative input and conducts quantification of the three main sources of operating performance delays, equipment, ground and schedule problems, in a cash flow simulation. A methodology for the assessment of operating risk in mine feasibility studies is presented.

Jan 1, 2011

By Andrew H. Stearn, Robert O. Agbede, Edward F. Divers

The ability to compete profitably in a competitive, demanding and specialized market, requires all components of productivity to be optimized toward the same manufacturing goal. This ever present requisite is seldom more apparent than with the quality control (PC) considerations that confront the super-refined metallurgical production necessary for today's exacting technical applications. In a work-place that already exceeds all environmental standards for cleanliness, this paper describes the development of specific environmental mechanisms and controls implemented at a titanium processing facility to impact both the minimal air-borne particulate contaminants and excessive process heat generation which are believed to degrade product purity. Based on the analysis of a carefully structured and instrumented field survey, two alternative solutions were proposed to modify the present facility utilizing a forced air (blowing) system. The first scenario requires ambient air to be drawn from a louvered rooftop installation and ducted to specific zones within the plant with appropriate weighted louvers and wall and roof exhausters designed into the system for air control. The second scenario incorporates a properly sized baghouse to be used in conjunction with the first system.

Jan 1, 1991

By A. Yadav, B. Behera, G. S. P. Singh

The size of chain pillars in the Indian geo-mining conditions is primarily decided in accordance with the regulatory provisions. These provisions are of little help for deep longwall workings, exceeding the cover depth of 360 m. Furthermore, these provisions are primarily meant to support pillars in bord and pillar workings. They may not be suitable for the chain pillars owing to a significant difference in layouts and functional requirements. Hence, it is imperative to develop a method to evaluate the stability of the chain pillar considering the complex loading and geo-mining conditions. To this end, a machine learning-based model was developed in this study to assess the stability of the chain pillars under high depth of cover considering the field-representative conditions. The data for this work was generated by conducting a parametric study using a field-validated numerical model. The strength and deformability parameters of the caved, fractured, and continuous deformation zones were established by calibrating the numerical model outcomes against the site-specific field observations. The developed ML model was used to evaluate the influence of pillar width, pillar height, cover depth, abutment angle, face length, coal strength, moduli ratio of the roof and floor strata to the coal seam, and the elastic modulus and unit weight of the overburden on the chain pillar stability. An interesting finding of this study showed that the factor of safety of the chain pillar increased with the increasing abutment angle, which may be indicative of the confining effect of the abutment angle on the pillar. Eventually, the ML model was verified by comparing its outcomes with the calibrated numerical model for a typical longwall working from Indian geo-mining conditions.

Oct 18, 2023

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

By W. G. Pariseau

Recent advances in rock mass mechanics and computational technology now allow for stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time-dependent. All the usual dry mine parameters including the premining stress state and rock mass properties are taken into account, in addition to water pressure and flow in jointed, possibly porous, rock masses. Finite element analyses of shafts and tunnels as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor, or equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and that the minimum safety factor at the wall in the wet case is always less than the dry case regardless of drainage time allowed.

Jan 1, 1995

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

By R. M. Balderrama

Bench-scale laboratory flotation and gravity separation tests were conducted on tailings samples to remove the sulfidic material, mainly pyrite, the source of acid generation. A combination of xanthate collectors, promoters, and frothers were used during flotation. Pyrite recoveries were in the range of 42 to 97%, depending on the tailings being treated. Sulfide sulfur contents of 12.8 to 0.37% in the feeds were reduced to 8.68 to 0.01% in the treated tails. Flotation tests were conducted to evaluate the ARD potential as a function of percent pyrite remaining in the tails. Standard ARD predictive tests were used to evaluate the success of the treatment. In some cases, removal of only 50 to 55% of the pyritic fraction was required, thereby demonstrating the conversion of the waste material from acidic to non-acidic. A laboratory vanning table was used to evaluate the amenability of sulfide-bearing tailings samples to gravity separation. The pyrite recoveries varied from 38 to 86%. The sulfide sulfur content of 12.8 to 0.37% in the feeds was reduced to 6.0 to 0.14% in the treated tails. Predictive ARD tests performed on tailings before and after the gravity removal of pyrite showed that most samples changed from "probably" acid producing to the "uncertain" range. Data reported and analyzed in this paper demonstrate source control for ARD prevention through the removal of metal sulfides from sulfide-bearing wastes using conventional flotation and gravity separation techniques.

Jan 1, 1995

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By Patzen Wu

The Hai-Shan No. 1 Coal Mine, located in northern Taiwan, is one of the typical coal mines on the island which, limited by natural condition, are mostly small in scale. With the advancing longwall method, the mine is now winning a seam, 80 cm thick, at a 32° dip, with a working depth of 824 m below surface. The annual output is about 50,000 mt of clean coal. At the working gallery, the virgin rock temperature may go up to 46°C, difficult to be brought dam to n acceptable level: because .of the tropical climate with high intake temperature and high humidity. Besides, at this depth, the intake air that goes down the long inclined shaft generates considerable heat due to autocompression. The mine is ventilated by a set of axial-flow fan with 38 m3/S of intake air at 2.2 KPA WG. With this volume of air, the temperature at the working-face is usually above 30°C WB. Appreciable lowering of the temperature is not expected even with an increased volume of ventilated air. For this reason, decision has. been made to try the installation of a pilot underground refrigeration unit near. the lowest gate road to cool the intake. air. from 32°C WB to 28°C WB which seems acceptable to on-the-spot workers exerting heavy physical labor. The experimental unit is designed for carrying away a total heat load of 90 Kw. The capacity of the unit is 200 Kw. The unit consists of a compressor, an evaporator, a condensor and a motor. The heat rejection is done in a cooling tower. Chilled water is circulated from the evaporator to the cooler by insulated pipes. The cooler consists of 90 Kw-coils with two fans and forces air by flexible ducting onto the working face. This paper examines mainly the effect of this additional reduction of working temperature, on working efficiency of the workers. Another aspect of this experiment is to evaluate the overall economy of underground refrigeration in small-sized coal mines under tropical condition. The success of such an experiment may lead to wider application of refrigeration to render many of the deeper mines economically workable.

Jan 1, 1980

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By Michael H. Vallez

On September 13, 1973 MAPCO Inc. leased from Pocahontas Land Corporation an 18,000 acre tract of coal lands in Eastern Kentucky's Martin County (See Figure 1.). In July, 1974 initial run of mine coal shipments commenced and in April, 1976 shipments of a 12,500 BTU, less than 1% sulphur, washed coal was being shipped. Results of exploration demonstrated that large quantities of overburden would have to be moved. MAPCO decided to invest in large surface mining equipment to tackle the job.

Jan 1, 1981

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By Biswajit Samanta, Pranjal Pathak

This article presents a customized genetic algorithms (GA) with new crossover and mutation operators to solve the short-term production scheduling problem of multi-mine mineral value chains (MVC). The preceding problem consists of determining the extraction sequence and destination allocation of blocks from all the mines collaboratively while closely meeting the quality and quantity requirements of the processing units subject to relevant technical and operational constraints. The short-term production scheduling is carried out at shorter scales wherein the operations are modeled in a great detail with large number of constraints. This makes the industry-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. Thus, a GA-based heuristic approach is developed to obtain nearoptimal solutions to the large-scale instances of the problem in a reasonable amount of computational time. Computational experiments show that the developed GA-based method is a promising way to handle industry-scale instances of the problem. Moreover, the sensitivity analysis on various parameter combinations of crossover and mutation operators indicates that the customized global mutation operator, when used in combination with the customized crossover operators, took on average 12.5% less time than the customized local mutation operator to converge to a solution.

May 21, 2022

By Nelson Alonso Portal Ravichaua, Melissa Esther Mendoza Tirado, Raúl Arévalo Saavedra

This study analyzes the implementation of an integrated strategy for environmental education and community awareness in Cajamarca, Peru—an Andean region affected by climate variability and the public perception of miningrelated water shortages. In collaboration with the Interactive Water and Earth Museum and the Newmont ALAC Foundation, three-month campaigns were conducted in schools and local communities. Key topics included the water cycle, climate change, and water availability, linked to urban infrastructure projects that improved flow rates through strategically located tubular wells tapping underground aquifers. The initiative addressed the challenge of communication in a context where mining is often blamed for scarcity, fostering scientific understanding of contributing factors. The study highlights how science-based outreach and institutional collaboration can strengthen resilience and promote sustainable water stewardship in mining-influenced regions.

Feb 22, 2026