Search Documents

By Alfred F. Savage

The Oglebay Norton Company has traditionally been a supplier of metallurgical grade fluorspar gravel to the American steel industry and, in the early sixties, fluorspar pellets were entered into the market. The gravel has been imported from Mexico, the pellets were produced by the Minerva Company in southern Illinois. While the acceptance of the pellets by the industry was satisfactory, overall marketing considerations caused the Minerva Company to discontinue the pelletizing operations. Thus it was that Oglebay Norton came to the decision to revive earlier plans to produce fluorspar agglomerates. A survey of the market and related factors led into two basic conclusions: 1) Because of steel plant safety considerations, flat, pillow- shaped briquets were preferable to easily rolling, marble-like pellets. 2) Briquets competitive with gravel could be produced by cutting imported, low-duty, acid grade spar to metallurgical grade by limestone and binders. A plant was built in Brownsville, Texas, and started operations in early 1970.

Jan 1, 1975

By Jacques B. Wertz

It is well known that the major fractures and lineaments presently recorded in Western North America are preferentially oriented along a general northwest direction (Figure 1). There are other features, however, more subtle, more elusive as a rule and which can only be inferred, occurring at right angle to this broad NW direction. It is intended a) to examine some of these NE or transverse trends, b) to compare these regional NE breaks to similar ones that transversally cut through the eastern part of the European Tethys, more specifically in Iran and Turkey, and c) to study their potential relationship to mineralization in both areas.

Jan 1, 1973

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By M. K. Mohanty

Over the years, screen bowl centrifuges have been widely used for dewatering fine coal in coal preparation plants in the United States and elsewhere. Its popularity is attributed to its relatively low cost, its high capacity of providing low moisture content product and its relative ease of operation and maintenance. It is generally recognized in the engineering and scientific communities that screen bowl centrifuges provide some degree of particle size separation while dewatering fine coal in a common application. However, the extent of differential partitioning of coarse and fine particles achievable by a screen bowl centrifuge has not been systematically studied in the past. The present investigation was aimed at conducting a parametric study using a statistically designed experimental program to better understand and optimize the size classification performance of a screen bowl centrifuge. A continuously operating screen bowl centrifuge having a bowl diameter of 0.5 m was used for this study at the Illinois Coal Development Park. Three key operating parameters, i.e., feed flow rate, feed solid content and pool depth, were varied to conduct a total of 17 experiments using a three-level factorial test matrix. Some of the best size separation performances achieved in this study may be described as having an imperfection value of 0.13 at an effective separation size (d50c) of 38 µm and an imperfection value of 0.27 at an effective separation size (d50c) of 2.8 µm. Due to an effective separation of ultrafine high ash materials, the ash content of the screen bowl feed was reduced from 22.3% to a minimum of 8.84% with a combustible recovery of 84.1% and an ash rejection of 71.6%. A higher combustible recovery of 92.1% was achieved at a product ash content of 12.5% with a d50c of 2.8 µm and imperfection of 0.27.

Jan 1, 2008

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation's peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986

By H. Colin

The basic industry, such as mining, ferrous and non-ferrous, cement and aggregates, stores and handles millions of tons of raw materials, re- quiring often different types of storage, blending and reclaiming systems.

Jan 1, 1980

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

By Lisa Morrison

The 11th Annual Mineral Economics and Management Society (MEMS) conference was held April10-12, 2002, in Montreal, Quebec. It consisted of a series of technical sessions. Each paper addressed the economic issues that are related to the changes that many people believe are now required in the mining industry. Some of the papers were directed at how the mining industry will handle the changes that will be required in its philosophy and operations management. Of equal importance was whether the industry possesses the toolkit necessary to effect these changes and emerge stronger from its challenges.

Jan 1, 2002

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.