Search Documents

By G. P. Richards

RIP is the process of recovering uranium from an unclarified slime pulp which comes in contact with a moving bed of ion exchange resin, T e sand-slime separation of the acid-leach slurry is accomplished through the use of cyclones and spiral, akins type classifiers. Course sands are discarded to tailings and the combined slimes and leach liquor become the IX feed. Uranium in the IX feed is absorbed on the resin and after exhaustion the barren pulp is directed to tails, Following the uranium exhaustion cycle an eluant solution passes through the resin bed stripping the uranium from the beads, The uranium is precipitated from the clarified pregnant eluant, filtered, dried and packaged for shipment to the AEC, Normally, the ore received at the Mines Development plant is a loosely cemented sandstone containing small quantities of clay and bentonite, The ore is easily crushed and requires only a 1/3 load of rods in the rod mill to reduce the ore to grain size, Very little of the ore is recirculated by the 42" spiral classifier.

Jan 1, 1958

By L. Barry Phelps

Coal mine drainage, which occurs predominantly as acid mine drainage in the East, is a serious contaminant of surface and groundwater systems (Appalachian Regional Commission, 1969). Treatment of this pollutant can be very costly and is often difficult to achieve (Appalachian Regional Commission, 1969). A major source of coal mine drainage in surface waters is polluted ground- water discharge, therefore treatment of surface water does little to combat groundwater contamination. Prevention of the formation of coal mine drainage and restricting its entrance into the groundwater protects both surface and groundwater systems. The formation of acid mine drainage may be inhibited by preventing contact between toxic spoil, air, and water (Grim and Hill, 1974). This may be accomplished by surrounding toxic spoil with a relatively impermeable barrier, thus restricting groundwater and oxygen flow through the toxic zone. Toxic spoil packages constructed in this manner would minimize the entrance of acid mine drainage into the groundwater system, allowing dilution by uncontaminated water to occur. If successful, concentrations of coal mine drainage would be reduced below toxic levels.

Jan 1, 1981

By Robert C. Salak

The era of low-seam mining with continuous haulage has been here for quite some time. Typical tonnages in companies such as Terry Glenn Coal are currently averaging 405 tonnes per shift in .8m coal. JoAnn Coal has averaged 453.6 tonnes per shift in .775m to .825m coal for the past four years. John Chaney of Chaney Coal has averaged 297 tonnes per shift in .6m to .65m coal. There are many other mines that are experiencing similar success and with maintenance costs that are averaging $.10 to $.40 per tonne. These figures have been documented and can be verified by the operators.

Jan 1, 1981

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

By Charles J. Kucera

Today's highly publicized issues of resource development and environmental protection are not new. But recently these issues have been played one against the other, and some would have us believe they are mutually exclusive. Why? Because modern man has realized that the shortest route to achieving economic progress is to subdue nature. He extracts mineral resources from the earth to provide the raw materials upon which other processes and services are based. But often in his search for economic progress he finds that other highly- held values (e.g., an unspoiled environment) have been violated. The natural response is a counter action - to attempt to protect nature. But this response is basically unsatisfactory because it is reactive.

Jan 1, 1979

By A. Arik

1his paper presents a modified ordinary kriging technique referred to as the "Nearest Neighbor Kriging" (NNK). The method is a simple and practical tool to use when the ordinary kriging (OK) results are unreasonably smooth, especially when estimating recoverable ore reserves for deposits with skewed grade distributions. NNK is robust and globally unbiased like OK. However, it is more advantageous over OK because it can control some of the smoothing and conditional bias which have been the major pitfalls of OK in many grade estimation cases. The paper details the methodology of NNK and its application to a gold deposit.

Jan 1, 1998

By D. R. McGregor, B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters of a column cell installation that replaced a conventional two-stage copper flotation cleaning circuit at Magma Copper Co., San Manuel, AZ, using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey are also discussed.

Jan 1, 1988

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Francis S. Kendorski

INTRODUCTION Caving offers the lowest cost per ton of any large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently taken on new importance as deeper lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface min¬ing methods, and too low grade to support any type of underground mining except a bulk method such as caving. Announced discoveries or indications that may be amenable to caving include: Climax's Mt. Emmons molybdenum discovery in Colorado; Molycorp's Goat Hill molybdenum prospect in New Mexico; the Phelps Dodge molybdenum deposit in Beaver County, UT; Arizona copper occurrences such as Asarco's Sacaton, Hanna's Casa Grande, Noranda's Lakeshore, and Ken¬necott's Safford; Anaconda's suspected deep copper de¬posit in Butte, MT; Anaconda's Carr Fork, UT, deposit; and perhaps others. CAVABILITY'S ROLE IN FEASIBILITY STUDIES Caving is a system of underground mining which removes support from underneath an ore body. As a result, the rock mass fractures, fails, and flows vertically downward by gravity to be collected in previously ex¬cavated funnels. Types of ore that have been mined by caving include molybdenum, copper, iron, nickel, as¬bestos, and diamonds (Julin and Tobie, 1973). It is primarily a large-scale method, with production rates of more than 45 300 t/d (50,000 stpd) having been achieved. However, the initial capital investment before return is very high, often in the hundreds of millions of dollars. The cavability of an ore body or mineral occurrence is a critical item in the feasibility study of a proposed mine, not only from the point of overall minability, but from the point of impact on other costs such as blasting, loading, hauling, crushing, and grade recovered. Aside from the often-asked question of, "Will it or will it not cave?" the real questions are, "Can we afford to make it cave, carry the rock away, and extract the mineral?" The last is not a topic of this chapter, but the first two are. The cavability of an ore deposit or mineral occur¬rence is based on many things, but clearly, if a large enough area is undermined, any rock mass will cave. The result could be a violent collapse as occurred at Urad, CO (Kendrick, 1970), or perhaps the rock mass will cave beyond the ore boundary. Another unfavor¬able result could be ore blocks that are too large for the equipment and orepasses to handle without considerable secondary blasting. Weak rock with numerous fractures may produce a very fine ore when it caves, resulting in dilution and ground control problems. DETERMINING STRUCTURAL DOMAINS It has long been recognized that the geologic nature of an ore body is important to cavability (King, 1946). Such items as weak rock material, intensity of fractur¬ing, and severity of faulting all contribute to the success of a caving operation, and information regarding these is required as a minimum for the cavability determination. In practice, the rock mass-defined as the blocks of intact rock together with the intervening fractures, joints, faults, bedding planes, and other discontinuities-that contains the ore body, as well as the surrounding and overlying rock, must be examined in a systematic and detailed fashion. Surficial geology maps must be pre¬pared, exploration holes drilled, and core logged for en¬gineering information. The fracturing of the rock mass must be studied to ascertain the three-dimensional dis¬tribution of fractures and their characteristics, and faults must be located and described. The strength and other mechanical properties of the rock material, the fracture surfaces, and the fault filling materials must be tested and reported for later use by designers and planners. With this basic information and an understanding of the geologic setting, the rock mass can be divided into one or more structural domains which tend to behave similarly in response to engineering activities (Robertson and Piteau, 1970). One must keep in mind that the determination of the structural domains goes beyond the geologic units present. Several lithologic units may be lumped together, while a single lithologic unit can be divided into multiple domains. Major faults often form their own domain, and the direction of engineering ac¬tivity-for example, cave advance to the north rather than the south-may alter rock mass behavior, resulting in different domains. As an example of the detailed rock fracture map¬ping required for such studies, the structural domain determinations at the Climax mine (Kendorski, 1973) are shown in Fig. 1. The circles are Schmidt equal area projections of the three-dimensional attitudes of frac¬tures (Ramsay, 1967) mapped in detail at various rock exposures. The attitude of fractures is important to the cavability determination since it dictates the directional behavior of the rock mass as it fails, and determines the effectiveness of arching, keying, and rock block inter¬locking. Low-angle fractures must be present to allow movement of the rock in the vertical direction during undermining (Mahtab and Dixon, 1976); if low-angle planes of weakness are absent, the rock mass may arch with a keystone effect, rather than moving vertically downward.

Jan 1, 1982

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

The most complete mining show ever held in the United States and the largest exposition of its kind to be held anywhere in the world in 1988. That's how the American Mining Congress is billing its "MINExpo International '88," to be held April 24-28 at Chicago's McCormick Place, the largest exposition facility in the country. MINExpo International '88 will combine for the first time two previously separate AMC-sponsored shows - the International Coal Show and the International Mining Show. Starting with the 1988 show, MINExpo International will be held every four years. The next show, in 1992, will be held in Las Vegas. The MINExpo in Chicago will feature more than 500 mining equipment and services exhibits covering 3 hm2 (320,000 sq ft) of exhibit space. Exhibitors will display products ranging from small safety devices to large earth-moving equipment. MINExpo is one of the few trade shows selected by the US Department of Commerce for its Foreign Buyer Program. Commerce is working with US embassies around the world to publicize MINExpo and to form delegations of visitors from many countries. Overseas visitors to the show will be assisted at an on-site International Business Center. It will provide currency exchange, translation, and other services to foreign buyers. Registrants at MINExpo will also be able to attend their choice of 27 morning-only program sessions. At these sessions, international mining experts from industry, government, and academe will analyze technical, strategic, and policy matters and discuss the outlook for the industry. "Toward the 21st Century" is the theme of this year's program. The technical workshops and managerial seminars are designed to assist mining executives, engineers, and geologists as well as mine superintendents, managers, and foremen in handling their responsibilities. Based on previous attendance at AMC international mining shows, the association says that more than 25,000 persons are expected to attend the Chicago show. It is expected that approximately 15% of the attendees will be from foreign countries. The Soviet Union will be among those exhibiting at MINExpo. The Russians have leased more than 2.8 dame (3000 sq ft) of space to display their mining machinery and equipment. It is the first time that the Russians have joined in an exhibition of mining equipment in the US. The two largest manufacturers of mining equipment in the Soviet Union, Setmash and Avtoexport, will put on display in Chicago a variety of Russian-made equipment. It will range from 100 t (110 st) heavy-duty dump trucks and diesel engines to drilling, hoisting, and conveying equipment. In addition to some 400 US exhibitors of mining equipment and services at MINExpo, nearly 100 companies will be present from other major mining nations such as Australia, Canada, Great Britain, Japan, the Netherlands, and West Germany. And, for the first time, a Chinese manufacturer will take part in the AMC show, participating with its US marketing partner.

Jan 3, 1988

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By E. A. Domínguez

Kaolin deposits of Patagonia (Argentina) were formed by ?in situ? alteration of volcaniclastic rocks or by erosion, transportation, and deposition of residual clays in small basins. The mineralogy, geochemistry, grain size distribution, and specific surface area of natural and washed kaolins were studied in order to point out the relationships with the ceramic process. Primary kaolins are coarse-grained, kaolinite+quartz±halloysite, with a very low specific surface area. Sedimentary clays are either kaolinitic?smectitic and very fine-grained or kaolinitic with a coarser particle size distribution. An interdependence between mineralogy, chemistry, particle size distribution, texture, surface activity and ceramic behavior was found. Plasticity is strictly dependent on surface activity and expandable clay minerals. Slip rheology is affected by soluble salts, smectite, and tubular halloysite. Kaolinite-halloysite play an opposite role versus smectite-I/S in slip casting and tile pressing. Kaolinite and quartz are beneficial for drying behavior while expandable clay minerals increase drying sensitivity. Firing behaviour is mainly affected by minor components supplying fluxing oxides.

Jan 1, 2010

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By Elham Najafi, Sina Ghassa, Ata Akcil, Hadi Abdollahi, Sandeep Panda, Zohreh Boroumand

Bioleaching is an environmental friendly process that has gained much interest for the production of metals from metal-bearing wastes or materials. The process decreases carbon footprint by reducing consumption of fossil fuels. Iron is a key factor in acidophilic iron-oxidizing bacteria’s activity, which is used extensively in the bioleaching of sulfide minerals. In the present study, the effect of different iron sources is investigated on sphalerite (ZnS) bioleaching. For this purpose, the effects of FeSO4  .7H2O, Fe2(SO4  )3 and FeS2 (pyrite) were studied on bacterial activity, and zinc (Zn), lead (Pb), cadmium (Cd) and arsenic (As) dissolutions were monitored from a ZnS concentrate. Under optimum conditions, the dissolutions of Zn, Pb, Cd and As were found to be 39.8, 0.1. 0.03 and 10 percent, respectively, in 25 days.