Search Documents

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By William T. Jr. Renfroe, Donald C. Gipe

INTRODUCTION Historically, pollution control in the metal-ore mining industry has been very limited. Unless mine water contained large quantities of solids, it was generally discharged without any treatment. If treatment was used to control solids, it was principally the provision of a settling basin in the form of a tailings impoundment used in conjunction with an associated metal ore dressing facility. Recently, however, a growing awareness of the adverse environmental impacts of mine drainage, coupled with strict environmental laws, has prompted the mining industry to look at new technologies and to refine the existing methods to further treat the wastes generated. This industry is unique in that waste loadings are extremely variable, and a "typical facility with typical waste loads" does not exist. Consequently, one waste- water treatment system cannot be utilized on an industry wide basis; rather, each treatment system must be designed specifically for the pollutants in each individual discharge. Public Law 92-500, the Federal Water Pollution Control Act (FWPCA) Amendments of 1972, became effective on Oct. 18, 1972. This law completely restructured Federal laws and philosophies underlying the Federal approach to water pollution control. Prior to the 1972 amendments, the principal Federal regulatory tool had been water-quality standards based on a designated use for a particular body of water. The concept was that waste disposal into water bodies is a desirable and acceptable use of the water body if it does not interfere with other beneficial uses. This had the effect of requiring various degrees of treatment and, consequently, various economic hardships on industries de- pendent upon their location. In many waterways. it is very difficult to quantitatively relate discharges to water quality. The 1972 amendments changed the basic philosophy, as stated in the Senate Committee report on the bill, to ". . . no one has the right to pollute . . . that pollution continues because of technological limits, not because of any inherent right to use the nation's waterways for the purpose of disposing of wastes." Pursuant to Sections 301, 304(b), and 306 of the FWPCA Amendments of 1972, the US Environmental Protection Agency (EPA) was required to establish effluent standards applicable to all industrial discharges. These standards must be based upon the application of the "best practicable control technology currently avail- able" (BPT) and the application of the "best available technology economically achievable" (BAT). The BPT and BAT levels must be achieved industry-wide by July 1, 1977, and July 1, 1983, respectively. WASTE SOURCES The waste-water situation in the mining segment of the ore mining and dressing industry is unlike that encountered in most other industries. Most industries (e.g., the milling segment of this industry) utilize water in the specific processes they employ. This water frequently becomes contaminated during the process and must be treated prior to discharge. However, in the mining segment, process water normally is not utilized in the actual mining of ores (exceptions are hydraulic mining operations and dust control), but it is a natural occurrence that interferes with mining activities and must be removed before mining can commence. Water enters mines by ground-water infiltration and surface runoff, and it comes into contact with materials in the host rock, ore, and overburden. The underground mine must pump large quantities of ground water to prevent flooding of the mine. Water from surface mining operations generally occurs as a result of surface runoff of rainwater. Generally, mining operations control surface runoff through the use of diversion ditching and grading to prevent, as much as possible, excess water from entering the working area. Nevertheless, some surface runoff does come into contact with the working area and may become contaminated. The quantity of water from an .ore mine is unrelated, or only indirectly related, to production quantities. De- pending upon its quality, the mine water may require treatment before it can be discharged into the surface drainage network. The variability of water quality from mines can best be demonstrated by looking at Table 1. This table shows the range of pollutant concentrations in untreated discharges from three different categories of mines (as categorized by EPA in the development of BPT and BAT effluent standards for the metal-mining industry). Data for this table were obtained during EPA's preparation of effluent standards for this industry. The parameters shown on the table are the pollutant parameters of primary interest in this industry; blanks in the table indicate that data were not available, and the parameter is not expected to be present in significant quantities. Other pollutant parameters are present in mining waste water, but they are either incidentally removed in the treatment process or are found only in trace amounts. The three categories comprise more than 90% of the metal production value in the United States and approximately 95% of the total mine discharges. It is important to note that not all parameters are found in significant concentrations at all locations. IMPACT ON WATER QUALITY One of the most troublesome mine-drainage problems is acidity. Although generally associated with coal mining, acid mine drainage frequently occurs from other types of mines. Although the exact mechanism of acid mine drainage is not fully understood, it generally is believed that pyrite (iron sulfide, FeS,) is oxidized by oxygen (Eq. 1) or ferric iron (Eq. 2) to produce ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) . The mining of ores associated with pyritic material exposes the pyrites to water and oxygen and grossly accelerates the natural oxidation processes, resulting in the significant production of acid mine drainage.

Jan 1, 1982

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By Harrison R. Cooper

INTRODUCTION AND SUMMARY Phosphate matrix beneficiation is the process of providing a mineral product suitable for downstream chemical processing to yield high analysis chemical fertil- zers. Extraneous contaminants, clays and gangue solids, are separated by screening and flotation. Reject materials always carry with them some phosphate mineral values, however. A continuing objective is minimizing phosphate losses discarded with tailings as a principle factor in maintaining beneficiation efficiency. The quest for efficiency, and improved productivity, during beneficiation is hampered by disturbances arising from among the following: o Natural variance of phosphate deposit compositions, o Minimal control over managing ore matrix supply to the plants, o Screening and flotation mechanical upsets and inefficiencies. Production personnel, in recognizing these factors, attempt corrections for changed process conditions. This response usually has limited effect. Efforts of product- ion personnel to correct for upsets of the process may often diminish efficiencies rather than improve them. Lack of prompt data for analysis of process streams is an important contributing cause of inefficient operation. Discussion in this paper examines methods for improved process control in Florida phosphate beneficiation with particular emphasis on use of on-stream analysis to aid gaining productivity. The Florida Institute of Phosphate Research has supported demonstration of on-stream analysis applicable to improved process control. Concurrently, work is proceeding world-wide in the phosphate industry toward practical on-line analysis technology. Table 1 summarizes viable methods for real-time analysis data as result of work by individual companies and research organizations. A recently completed investigation (sponsored by the Florida Institute of Phosphate Research) of beneficiation efficiency was carried out in two Florida beneficiation plants using a newly developed on-stream analyzer for phosphorus (1). BPL measurements were taken at frequent intervals over two to three weeks of routine operation. Grades are expressed in "BPL", with one BPL, or bone phosphate of lime unit, equal to 0.46 P^Y2^YO^Y5^Y. The time series of feed and tailing BPL data were evaluated by statistical procedures. Results show avoidable losses can be five per cent or greater of mineral values in feed. Use of modern process control methods in Florida phosphate mining began several years ago (2, 3). Benefits of stabilizing control used in one of the two plants where data were collected for the investigation, in comparison to manual control in the other, are outlined. Process control technology developments reported from European and South African phosphate mining operations are also noted (4, 5). It is now well accepted that advanced control techniques can increase beneficiation productivity by better management of losses. However, to make advanced control effective, real-time measurements are needed of feed and tailings BPL as well as mass flow rates.

Jan 1, 1993

By D. Spindler

Pursuant to the Federal Surface Mining Act of 1977 and the Illinois Surface Mining Act of 1980, Illinois has adopted revegetation success standard regulations that include the Agricultural Land Productivity Formula. The Formula establishes yield goals and standards to measure the success of meeting yield goals for reclaimed prime farmlands. The formula compares the quality of the pre-mining soils in the permit area and the county, to the crop production achieved on the reclaimed permit area and the county crop yield in a given crop year. The regulations also specify acceptable crops, erosion control requirements and time frames for demonstrating success.

Jan 1, 1986

By X. Xie

The dissolution behavior of palladium powder in thiourea solutions has been studied. The variables studied included temperature, stirring speed, and concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was found to be chemical reaction controlled with an apparent activation energy of about 2S.3 kJ/mol.

Jan 1, 1995

By Steven F. Hoerger

Newmont Gold Company is the largest producer of gold in North America. Accurate resource estimates are critical to planning the mining in a year of over 90,000,000 t (100,000,000 tons) of mill, leach and waste grade material, from which over 47 t (1,500,000 oz) of gold are recovered. Resource estimates are updated frequently to take advantage of new drilling, improved geologic understanding and additional production reconciliations. At Newmont Gold, indicator kriging is the primary method being used to create resource estimates. Indicator kriging (IK) is a well accepted method of resource estimation; however, many details of the IK process which are critical to producing a useful resource estimate have not been well documented. An IK model must have several characteristics in order to be a useful resource estimate: the model must take into account geologic features of the mineralization; model creation cannot require too .much time; the model must accurately reflect the effects of selective mining; the model must be stored in an easily accessible format; and the model must be useable with a variety of cutoff grades. This paper will show how Newmont Gold implements the IK process in order to achieve these goals.

Jan 1, 1992

By W. G. Pariseau

A study of coal pillar strength at the Beehive Mine in central Utah was done in the 1970s. This study was a cooperative effort by the University of Utah, RE/SPEC, Inc., and the American Coal Company and was funded by the U.S. Bureau of Mines. Mine measurements of closure at 117 points and pillar stress using 119 vibrating wire stress gauges were made during retreat mining in this room-and-pillar operation. Laboratory testing for the strength and modulus of 372 coal cylinders up 0.3 m (1 ft) in diameter and 0.6 m (2 ft) in length was also done. Two-dimensional finite element model analyses complemented the study. However, the real world of mining is three-dimensional and in consideration of the significant advances in computing power since the time of the original study, a revisit of the data seemed warranted. In this regard, a novel finite element method was used that allows for the whole-mine analysis of tabular excavations on the kilometer scale and yet enables details to be obtained at pillar walls on the meter scale. The effects of material properties variability in situ and of joints can also be taken into account. Results that compare computed two- and three-dimensional seam-level closures with mine measurements show noticeable differences; three-dimensional results are reasonable, while two-dimensional results overestimate closure by nearly a factor of two.

Jan 1, 2014

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60's increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By W. J. Bronkala

Dense-medium circuits have been installed in many mineral treatment plants since its, original development about thirty years ago. In the intervening, period the process has been thoroughly evaluated and many innovations have been introduced. The Heavy Density. Cyclone is one of the newer systems which has extended the operating range of this process to 65 mesh size. Several different finely divided materials have been used to produce the separating bath but nearly all new plants use a ferro-magnetic medium. The, advantages of magnetic medium include: 1. Smaller recovery plant 2. Lower cost recovery plant both in initial and operating cost 3. Excellent medium stability 4. Dependable medium supply at reasonable and stable cost. Magnetic separators are used to recover this magnetic medium and the smaller plants and lower operating costs are directly related to their use.

Jan 1, 1964

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

By E. Sirolli

In recent times, with rare exceptions, most economically viable ore discoveries have been large, low-grade and located in remote parts of the world. Mining companies have often shown to be incapable of mitigating their social and economic impact on local communities. Sustainable development and relations can be achieved by implementing bottom-up methodologies to the top-down tools already in use by mining companies. In order to magnify the importance of enterprise facilitation as a primary method for community development, data from 25 years of community based work around the world was used. Results highlight the need for a grassroots approach to local economic and community development, which focuses on the creation of a parallel economy in communities. Using solely top-down methodologies for developing community relations is shown to be a limited resource for mining companies. There are fundamentally two dangers for mining companies: alienating the local population, resulting in militancy and lengthy legal battles to obtain a license to operate; and, being accountable for building social and economic infrastructure that are not the company?s responsibility.

Jan 1, 2012

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987