Search Documents

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By C. Allen Born

There is a saying, the greater the gratitude, the shorter the speech. That puts me in a quandary, because while I am grateful for the honor you do me today, I also want to talk about a subject very important to all of us. A few months ago, when I was asked to submit a title for my talk, I chose "Quality where it counts." I did so because perhaps the most important thing we at Amax did in our restructuring was to commit to quality in all our businesses - quality people, assets, and operations. Together, they create quality performance, which produces quality growth and increased shareholder value - our prime corporate mission. We are dedicated to quality. At Amax, quality means everything. Today, I want to discuss quality in another context - the need for it in American education and what we have to do to achieve it. If we ignore this need, we will all suffer the consequences. And they will be upon us far sooner than the next century, barely a decade away. I think almost everyone in this room works for an organization that had to restructure in the 1980s. Mining companies that did not, just didn&apos;t make it. Well, we did. As an industry, we are seeing improved profits, positive cash flow, and a more competitive position in the world marketplace. But all the restructuring we have done, all the hard work, and all the pain that was part of it, will be in vain if, down the road, we do not have the educated people we need as workers. We need them to design, manufacture, and market the products that use the basic materials produced by the mining industry. Simply put, we are at a crisis point in education today. That is no new revelation. Nearly six years ago, the National Committee on Excellence in Education published its report, "A Nation At Risk." Since then, things have not gotten better. The Wall Street Journal, Business Week, US News & World Report, and Fortune have all recently published stories about the sorry state of education in the United States. The subject has become the topic of TV talk shows as well as national commissions, and for good reason. The pool of young people entering the US labor force is dwindling. In the next decade, 10 million fewer will enter the job market compared to the 1970s. But fewer of them will be qualified to do the jobs available to them. Here&apos;s why: • 20% of today&apos;s high school students drop out before they are 18 and another 20% graduate functionally illiterate; 40% of today&apos;s fourth graders think the world is flat; • 20% of today&apos;s sixth graders cannot locate the United States on a world map; • one of every three ninth graders cannot figure the change for a two-item meal - and I&apos;m talking about a Big Mac and fries. These are not just problems of minority kids in big city ghettos. Fully 40% of all young working Americans cannot add up their lunch bill. Three out of every five college freshmen need some kind of remedial work. These statistics are frightening. Particularly so because, while the work force is becoming less qualified and our public education system is getting worse, our products and technologies are becoming more complex. We are approaching a time when we will have machines that recognize handwriting but people who cannot write. We will have technology to take voice commands, but people who do not know what they are talking about. The accelerating pace of technology is changing the nature of the job market. The fastest growing jobs now, and in the years ahead, are in professional, technical, and sales positions requiring the highest education and skill levels. Most of these jobs will require the use of a computer. Yet, 95% of today&apos;s graduating high school students have never laid a finger on a computer keyboard. While our education system is failing the students it is supposed to serve, other countries are doing far better. In a

Jan 1, 1990

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By M. Leduc, M. Backens, M. E. Smith

An emerging technology for sustainable development in mineral development, tailings co-disposal™ is a means to dispose of conventional mill tailings within the void space of a waste rock dump. This method, while not applicable to all tailings systems, can offer a significant reduction in short-term and long-term environmental liability, land disturbance, closure costs, and negative public image. The concept is to dispose of the tailings simultaneously with the waste rock or leach ore, controlling the ratio of tailings to coarse material such that the resulting dump is stable both physically and chemically. The resulting co-disposal dump can be as safe as a conventional waste dump. In the case of alkaline tailings in a potentially acidic waste dump, the acid production can be buffered or slowed.

Jan 1, 2004

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat, A. J. S. (Sam) Spearing

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. Initially, ASTM A615 grade 60 steel roof bolts, which are the most commonly used bolt material in the United States, were tested with and without stresses in a simulated underground coal-mining environment for approximately six months. This paper mainly discusses the test system, protocol and system shortcomings, and makes recommendations based on the observations and results.

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Gabriel de Almeida

INTRODUCTION The widespread use of desktop computers by an ever increasing number of people, both for personal and for business and government uses, has brought public attention to surprising stories about computer abuse. Before the advent of microcomputers in the information processing environment, hundreds of amazing misdeeds involving large computers had already been reported, most of them perpetrated by highly skilled professionals. The undreamed enlarging of microcomputer potential has steadily posed a major threat to complex mainframe computing systems, as joyful teenagers become familiar with the habit of hacking around someone else&apos;s large processing system, by means of makeshift phone communication networks, based on their intended homework for personal computers -- for the sheer fun of it. Now, the never ending capacity and speed improvement of commercially available micros has given rise to a brand new concern for society: the hazards of processing sensitive information in the powerful, but still unsafe microcomputer itself, whether or not linked to other micros or mainframe networks. This paper deals with some aspects of the problems and presents some practical hints as to enhance protection and minimize risks to sensitive and secretive information when processed on microcomputers. The physical considerations of computer security and pertinent safety precautions will not be discussed, because while essentially relevant to information protection, recommendations are well defined by processing resources suppliers and their importance is more widely recognized by users in general. Definitions and Classifications. The following definitions and classifications will be considered in this report: Information Assets: Any knowledge or information processing, storing or conveying device displayed in one&apos;s environment. It consists of two main categories: INFORMATION RESOURCES: End user&apos;s application data wherever recorded. PROCESSING RESOURCES: EDP skilled user&apos;s hardware, software, peripherals, magnetic media, communication devices, auxiliary equipment, supplies and related operational procedures. Information Protection: In a broad sense this is the set of necessary procedures to assure to the legitimate user the effective control of the operation and allow modifications of information assets, so that their physical or cognitive integrity be preserved or any unexpected loss minimized inspite of accidental occurrences or intentional actions. Classification Processes: Commonly two classification processes are used to define key terms in information protection: SENSITIVE CLASSIFICATION: Pre-defined standards for assessing the vulnerability to losses due to lack of proper processing continuity if information is destroyed, disclosed, secluded, or misused. SECRECY CLASSIFICATION: A spectrum of degrees as to the expectancy of holding exclusiveness of unique information whose destruction, disclosure, seclusion or misuse will cause a negative impact on the legitimate holder environment. Sensitive Information: Any knowledge whose destruction. disclosure. seclusion or misuse - - - implies losses to its legitimate holder. It may be classified as: VITAL INFORMATION: An essential knowledge whose lack of proper availability implies total loss or termination of p

Jan 1, 1987

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year&apos;s Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson&apos;s equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.