Search Documents

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

Continued market pressure on the US coal industry was the overriding factor affecting developments in underground mining in 1986. An oversupply of coal in the spot market kept prices low throughout the year and caused a number of operations to close their doors. Operators stepped up their efforts to improve productivity at existing operations. They made technology advances and improved their relations with employees. A continuing market-related development during 1986 was the divesting of coal properties and operations by major oil companies, which were faced with economic pressures in both the oil and coal industries. Further increases in contract mining production resulted as some larger operators were unable to compete in a tough economic environment. Longwall mining is still seen by many as the technology that will provide the necessary productivity to remain cost-effective. But the number of active faces in the US declined in 1986, as reserves were depleted and economics forced some closures. At the first Longwall USA meeting in June, much attention was placed on improved technology, as electro-hydraulic controls for roof supports gained acceptance. Other recent developments include shearer initiation of roof supports, automatic horizon control for shearer drums, and collection and storage of machine data for predicting maintenance requirements. The government and academic communities continued their research on dust control at longwall faces. Jankowski, Kissel, and Daniel, (October 1986, Mining Engineering), gave an overview of progress in longwall dust control. And Mukherjee, Singh and Jayarman (November 1986, Mining Engineering), recommended design guidelines for improving water spray systems for dust control. Surface subsidence Increasing attention is being given to surface subsidence. This is primarily because of longwall mining and the Surface Mining Control and Reclamation Act. Improved methods of prediction of surface subsidence, especially computerized methods, are being continually developed. Mining engineering faculty at major universities such as Virginia are helping develop public policy and regulations concerning subsidence. As part of this effort, Unrug and Johnson identified major subsidence areas of Western Kentucky. Peng and Chen (February 1986, Mining Engineering), gave an overview of history and research of surface subsidence. And Elifrits and Aughenbaugh, (February 1986, Mining Engineering), discussed effects of moisture variations and overburden on subsidence. This research culminated in a Symposium on Surface Subsi¬dence at the SME 1986 Fall Meeting in St. Louis and the 2nd Workshop on Surface Subsidence at West Virginia University. Ground control in coal mining continued to be an item of major research interest. Some 30 papers were presented at the 5th International Conference on Ground Control in Mining at West Virginia University. And six sessions were related to coal mining at the 27th US Symposium on Rock Mechanics at the University of Alabama. At the 4th Annual Workshop, Generic Mineral Technology Center, Mine Systems Design and Ground Control emphasized efforts of the participating universities to improve ground control. Peng and Chiang summarized results of studying support capacity and roof behavior with longwall shield supports. And Unrug, Johnson, and Nandy analyzed the process of deterioration of shale roof in a case study of a room-and-pillar coal mine. The importance of geologic conditions in determining mining productivity is receiving increased attention in coal mine design in the US. Mullenex related, through case studies, the benefits to be derived through analyzing the depositional system of coalbeds as an integral part of mine design. Improved technology in this area was related by Lloyd, Semborski, and Stolarczyk. They discussed a case study of using radio imaging to indicate coal-seam discontinuities in advance of mining. Improved coal mining technology in general is being researched more heavily, to help improve US coal competitiveness. However, much of this research and development process has yet to be widely implemented. Equipment manufacturers are devoting more resources to development of continuous-haulage systems, mobile roof-supports, mine-monitoring systems, and predictive-maintenance systems using computers to extract machine data.

Jan 5, 1987

By H. B. Oblad

The WEMCO® SmartCell™ flotation machine is a continuously-stirred tank reactor in which solids are suspended in water and are contacted with air. The reaction is particle flotation resulting in the separation of valuable material from gangue. The effects of several operating variables on the flows of water and air and on motor power were measured. A miniature magnetic flowmeter was installed in the draft tube that allowed measurement of the water flows into the rotor. This work has led to a better understanding of machine function which will lead to improved performance and better operation. General equations for optimization, design, and scale-up were inferred.

Jan 1, 2002

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Craig M. Sams

Phosphate mines in Florida are continuing to encounter higher dolomitic content host rock with the phosphate pebbles(1) necessitating a change in grinding conditions and/or circuits, One of these changes is to install hydrocyclones and close circuit the mill as opposed to the traditional open circuit grinding plant. Close circuiting of the grinding mill with hydrocyclones allows one to take advantage of reduced process mill power requirements by circulating the coarse mill discharge back into the mill for multiple chances of particle breakage. Additionally, as in this case, the hydrocyclones de-slime the pebbles, allowing for more efficient use of grinding power by reducing the amount of dolomitic material recycled to the mill.

Jan 1, 1986

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. The US Bureau of Land Management, American Assay Laboratories, and the Minnesota Department of Natural Resources cooperated in a intralaboratory and interlaboratory testing of the protocol. Intralaboratory testing was conducted on duplicate samples of gabbro (8) and siltite-argillite (5) rocks for periods of 20 to 125 weeks. The difference between replica& intralaboratory pH readings on drainage from the gabbro for the drip-trickle leach alternative typically did not exceed 0.1 units, although differences as high as 0.4 units were observed. The difference from the mean for rates of sulfate, calcium and magnesium release was typically within 10%. Intralaboratory results for the siltite-argillite samples were generally similar, although a one unit pH difference was observed for one sample. Three different laboratories tested a gabbro sample for 125 weeks, with a maximum difference from the mean pH of 0.5 units. The percent difference from the mean for sulfate and calcium release rates was typically within lo%, although values as high as 30% were observed. Data on intralaboratory and interlaboratory agreement on the flood rinse alternative of the method were limited. Replication on the sample tested was comparable to of better than that observed for the drip-trickle method testing of the same sample.

Jan 1, 2000

By N. I. Aziz, B. Srinivasa Rao, R. N. Singh

The control of respirable dust and its subsequent exposure to miners is essential for improved safety in longwall mining. The extensive variation in face conditions and operations of longwall make numerical modelling an attractive approach in both the development and evaluation of dust control devices. Three dimensional finite element computational fluid dynamics code FIDAP was used to model air velocities and the effect of dust control techniques on dust concentrations at a typical longwall face. The effect of shearer body on airflow characteristics in a longwall face was analysed with both antitropal and homotropal ventilation systems. Path traces of particles introduced near the shearer drums was also simulated. Initial modelling results were validated using field trial results at three operating longwall faces. Results of simulations tallied very well with the field results.

Jan 1, 1993

By Christophe Bragard

The Los Angeles Metro Eastside Extension light rail project included a 1.5 mile underground segment, which consisted of twin 18'?10" ID tunnels, bored with two EPB-TBMs. One of the major project challenges after the completion of the bored tunnels was the excavation of six cross passages within alluvial geology below the water table and with low ground cover. Sequential excavation methods were employed and this paper details the design, ground treatment, support measures, and construction methods used to mine these cross passages beneath the congested urban streets of the City of Los Angeles.

Jan 1, 2008

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By Robert J. M. Miller

Thank you Mr. Chairman. For more than 15 years a debate has been taking place among students of massive sulphide deposits as to the origin of these deposits. Prior that time it was widely accepted that the deposits were of hydrothermal, epigenetic and even replacement origin (Wilson, 14). Kinkel, Knight, Stanton and others advanced hypotheses which would explain the, formation of the deposits by different, largely syngenetic, volcanogeric processes. I was fortunate in having become involved in exploration for these deposits at about the time the debate was beginning and thus had an opportunity to apply with some success, some of the new and old ideas for formation of massive sulphide deposits. The deposits which I will discuss today are all located n northwestern Quebec, in the Abitibi orogenic belt. Mattagami Lake Mines is about 100 miles due south and Noranda's Horne Mine about 200 miles south of James Bay. In 1959 I prepared a talk which was presented to the 1960 CIM Convention calling attention to the spatial and possible genetic relationship between the ore sulphides of the Mattagami Area, Quebec and the tuffite, as well as the structures which controlled the ore. In this present paper I would like to cover the following points: (1) The general criteria used by the epigeneticists to support their contention that the deposits were formed after the enclosing rocks.

Jan 1, 1973

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By W. W. Wen

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an mine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electrokinetic behavior of coals of different rank and degree of oxidation were studied by an electrophoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite was depressed. Comparing the flotation results with the electrokinetic results verified that in the presence of ferrous sulfate, the maximum hydrophobicity of oxidized coal with dodecylamine and frother is near its IEP which is around pH 6.5 to 7.0.

Jan 1, 1976

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By Ed Ramsay

The Hill is a cyanidation plant with flotation and roasting. The grinding and treatment have at the present time a capacity of 1400 tons of ore per day and the precipitation has a capacity of 6000 tons per day. The ore is delivered by a 36" conveyor belt and tripper to 8 mill bins having a capacity of 6000 tons. The ore from these bins is discharged onto 20" gathering conveyor belts which are regulated with p.i.v. speed changers to control the belt weight. A weightometer determines the tonnage milled. The feed enters the 8' x 12' rod mill through a rubber lined chute and the product is discharged through a launder to a 7' rake classifier in closed circuit with 10' by 6' hardinge ball mill. Lime slurry is added at the rake classifier to give a strength of .30#/ton. The classifier sand is fed into the ball mill with a scoop feeder and the mill discharge flows in a launder back to the classifier. The classifier overflow is pumped to a 24' by 12' bowl classifier in closed circuit with a 8' by 15' regrind mill. The bowl classifier sands are fed to this mill and the mill discharge is pumped back to the bowl. The bowl overflow at 8% - 200 mesh is the final product from the grinding circuit.

Jan 1, 1975

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999