Search Documents

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By Todd Wanless, Daryl Poduska, Prakash Donde, Mahmood Khwaja

"The proposed Minne Lusa Stormwater Conveyance Sewer is part of the Phase 3 Major Combined Sewer Overflow projects to be scheduled as part of the City of Omaha’s Long Term Control Plan (LTCP). The system features a 6,100 foot long, 14-foot inside diameter tunnel to provide for conveyance of separated stormwater from previously completed and future LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The tunnel will operate as a pressurized system and convey flows of up to 2,500 ft3/s resulting from a 10-year, 24 hour storm event. This paper provides a synopsis of the project with a focus on the overall design aspects related to siting the tunnel alignment in an urban environment, the hydraulic analyses performed to choose a pressurized system rather than an open channel system, and expected geologic conditions. Tunnel alignment and profile and geological profile are presented, as well as an overview of the construction related impacts considered during design. PROJECT BACKGROUND The proposed Minne Lusa Stormwater (MLSW) Conveyance System will provide for conveyance of separated stormwater from previously completed, and future, LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The project location is representatively shown on Figure 1; the overall conveyance system is represented in Figure 2. The MLSW Conveyance System consists of three separate construction contracts under Contract Numbers: OPW-52004 – The Storz West Detention Basin to 31st & Paxton Tunnel; OPW-52454 – The Storz West/Pershing Detention Basin Grading and Improvements; and, OPW-52752 – The Pershing Detention Basin to ML Outfall Channel. This paper focuses on the project covered under Contract OPW-52004: design and construction of an approximately 6,110 feet 14-foot inside diameter (ID) tunnel, constructed using a Tunnel Boring Machine (TBM). The tunnel will receive flows from the Paxton Boulevard (PB) and the John Creighton Boulevard (JCB) Stormwater Conveyance Sewers and convey the flows to the Storz West Detention Basin, resulting in CSO volume and flow rate reductions to the Minne Lusa Outfall Channel and the North Interceptor."

Jan 1, 2016

By M. Z. Dogan, M. S. Celik, G. Onal, O. Ozcan, I. Yildirim

A fluorite ore (51.85 % CaF2) containing high contents of calcite, quartz and iron oxides was upgraded by flotation using a new reagent, oleoyl sarcosine (OS). In addition, quebracho and sodium silicate were used as depressants for calcite and quartz, respectively. The effect of pH, collector and depressants concentrations on grade and recovery was determined with the aim of optimizing the flotation conditions. Application of the two-stage cleaning achieved a concentrate assaying 92.17 % CaF2 with 80.1 % recovery. The Si02 content (0.76 %) was below the required level of 1 % SiO2. The mechanism of interaction between OS and fluorite, as compared to oleic acid, is also elucidated based on the zeta potential measurements.

Jan 1, 1993

By X. P. Zheng

Barium fluorphlogopites were synthesized in the laboratory in order to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between layer structure and the Ba-O bond length. The higher barium content, the larger the cell volume and distance between the layer structure and the longer the Ba-O bond, the more negatively charged the surface is and hence the more easily adsorbed to cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1993

By T. Altman

Using theory of network planning together with graph theory, an algorithm is presented that creates canonical diagrams for mine ventilation networks (M VN). The data generated by the algorithm is used in the construction and plotting phases of a program that automatically plots the canonical diagrams, which can then be used for further studies of a given MVN.

Jan 1, 1988

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By Jerry W. Owens

Current steel consumption for grinding media, mill liners and rods in North America runs in excess of 400,000 tpy in the mineral processing industries. Steel consumption ranks as one of the major consumables along with energy in most operations with total annual industry expenditures in excess of $275 million. It is generally agreed that there are 3 main categories of wear responsible for this metal loss. These three main types can be loosely defined as follows; 1) Abrasion. The cutting, rubbing, scrapping and gouging of the metal surface by the ore with which it is in contact; 2) Impact. Spalling on both micro and macro scale, breakage, and deformation due to metal to metal contact; 3) Corrosion. The oxidation losses of the metal due to electrochemical interaction between the grinding media and the slurry

Jan 1, 1984

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By F. Grajales Munoz

The Cienega project, now under construction by Penoles group, is located in the mountains of the State of Durango, Mexico. The gold and silver deposits are found in the 4-km long system of veins, which will be extracted by underground methods. The planned 1000 tpd process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994.

Jan 1, 1994

By Pradip

The development of highly selective mineral processing reagents, which are not merely metal-ion specific, but specific to the particular mineral surface structure, is essential for the exploitation of relatively more difficult-to-process ore deposits, in particular for the separation amongst minerals having the same constituent ion. Both the choice of the functional group as well as the molecular architecture of the reagent determine its selectivity. Several examples are presented in this paper to illustrate the concepts of structure specificity and molecular recognition at mineral surfaces - the concepts crucial to the advancement of the emerging science of reagents design. Recent advances made in the understanding of molecular interactions involved in the synthesis of biomineralized materials are discussed so as to delineate the utility of this approach in the design of selective reagents for mineral separation.

Jan 1, 1994

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By Russell H. W. Chadwick

Reviewing events in the minerals industry, in economic geology, and in my own exploration work, I find that the most compelling subject for comment is the increasing ferment in ore deposits theory. New discoveries and continued investigations of bedded deposits of lead and zinc, copper, iron, uranium, etc., coupled with the availability of much new and significant data from sedimentary and metamorphic petrology, geochemistry, and oceanography, has led many economic geologists like myself to become disenchanted with former simplistic notions. Now disenchantment among serious people should presuppose both valid objections to the old, and valid new substitutes. I can sum up my own position and, I believe, what most of the recent writers on ore deposits theory are trying to tell us, by saying that a physico-chemical (bench science) approach to a natural science is neither correct nor useful, and that the obvious cure is a return to the study of the geology of ore deposits. More specifically, ore should be viewed merely as an unusual concentration produced, in stages, by the natural processes inherent in the geochemical cycle. In criticizing the conceptual basis of a science, one is involved simultaneously in the inherent character of the science, its subject matter, and the old and new concepts. I have found it impossible to make a clean separation along those lines. As a result, and as the title suggests, these are not-quite-random reflections on genesis, a matter near and dear to all true treasure hunters since Agricola.

Jan 1, 1967

By E. M. Van Eeckhout

The National Uranium Resource Evaluation Program (NURE) has produced a mass of geochemical data in the form of data files on tapes. This paper presents a methodology for utilizing those tapes in a simple, practical manner. An example is given of an analysis of the Butte quadrangle, Montana, tape obtained from the Los Alamos National Laboratory (LANL). The example details the sequence of splitting the data file, plotting histograms, cumulative frequency curves, concentration plots, and methods for evaluation. All programs are written in FORTRAN. The case study was performed using a mini- computer (DEC PDP 11/70) and standard plotting subroutines.

Jan 1, 1982