Search Documents

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By Walter P. Hansen

Belt conveyors offer a reliable means and often do the most economical job for providing continuous bulk material transport, whenever the terrain permits their installation. The ore processing, construction and mining industries use belt conveyors to carry all types of material, from small to large tonnages. Most of the conveyors Fluor Mining & Metals, Inc. designs for metallurgical plants are in the in-plant category, of limited length and medium tonnages, and use fabric carcass conveyor belting. Belt widths can range from 24 to 60 inches Generally, the layout and design of these belt conveyors present no unusual problems. However, calculations for belt tension and horsepower, design of materials transfers, and the sizings and layouts of belt pulley stations and their drives are time consuming.

Jan 1, 1979

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By Andrew McGrath, Geraldine Lyons, Sarah Barcelona

In the dynamic and challenging modern industry landscape, understanding and unleashing the true role and contribution of technical teams is crucial to business success. The cyclical nature of industries has led to shifts in the technical professional’s place within the organization and the technical skills that are desired most. This paper reframes the pivotal role that technical professionals play within complex operating assets to maximize value and realize full potential. This investigation focuses on the Rio Tinto Kennecott Technical group’s cultural journey, which is underpinned by an investment in its people. The conflict between legacy industry beliefs and the necessity for cultural change emerges. This is illustrated by a deep dive into the evolving case study of Kennecott’s Bingham Canyon Open Pit Mine Technical team. Here, a multi-faceted approach to cultural change is helping to unlock the team’s contribution to the life extension of an aging asset. Guided by a vision and strategic roadmap, this approach is part way through a 5-year implementation period and is yielding encouraging business outcomes.

Feb 1, 2024

By J. C. Cawley, G. T. Homce

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Jan 1, 2013

By Meredith Scaggs, Emily Sarver, Lucas Rojas Mendoza

"Early on Jan. 9, 2014, approximately 37,800 L (10,000 gal) of crude 4-methylcyclohexanemethanol (MCHM) leaked from a storage tank sitting on the bank of the Elk River near Charleston, WV (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal and is considered nonhazardous in terms of transportation, storage regulations and also toxicity (CDC, 2014a). Freedom Industries Inc., a producer and vendor of specialty chemical products, had acquired the storage facility from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein and McWhirter, 2014).The spill site was located a little more than 1.6 km (1 mile) upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a "Do Not Use" order was issued for all customers (WVAW, 2014a).With little information readily available regarding the potential human health effects of MCHM, the U.S. Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the "Do Not Use" order remained in effect for a total of eight days, until Jan. 17, when the WVAW distribution water was confirmed to have MCHM concentrations below the approved level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at sub-ppb concentrations, a fact that undoubtedly added to growing public concern (Rosen et al., 2014; Gallagher et al., 2014). In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until Feb. 25 when MCHM levels were measured below 2 ppb (WVAW, 2014b), and eventually replaced the affected filter media (WVAW, 2014c)."

Jan 1, 2014

By Richard C. Holmquist

Some of you may be old enough to remember -- as I do -- the early days of World War II. A highly prepared, well-equipped Japanese striking force had moved like lightning across the South Pacific islands and Southeastern Asia. As the invasion force pushed its way down the Malaysian Peninsula, Singapore stood serene and beautiful, protected by its natural moat of water, busy as ever with its commercial pursuits. One can see its captains of trade and industry now, sitting com¬fortably on the veranda of the "Singapore Country Club", sipping scotch between cricket games, convinced that the weary, logistically extended Japanese force couldn't possibly cross over to their island which had been so secure for a hundred' years or more. No need to remind you what happened. The brave men in their ships at sea and in the gun emplacements ashore were hopelessly out-gunned and out-maneuvered.

Jan 1, 1979

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By T. T. Toomver

The evolution of Inco's Selective Reduction Smelting Process as practised today is described, beginning with the initial laboratory experiments on small samples to the processing of large bulk samples through pilot plant equipment. For both the Guatemalan and Indonesian (Soroako) ores, the initial screening tests using hydro-, vapo-, and pyro-metallurgical processes showed that the latter was the most promising both metallurgically and economically. Later, larger scale tests confirmed the earlier testwork.

Jan 1, 1979

By T. B. Szwilski, R. D. Begley

Status of ISO 14000 standards. The ISO 14000 are voluntary international standards providing a frame-work that allows a company to integrate an effective environmental-management system (EMS) into its operations. The purpose of an EMS is to provide a systematic procedure to identify the environmental aspects of a company's activities, evaluate any significant impacts and use the information to set objectives and targets toward continuous improvement of the company's environmental compliance and performance. In addition to the specifications for certification, ISO 14000 can be used as a guide to develop an effective environmental-management system or for self-declaration. The International Organization for Standardization (ISO) is a worldwide federation founded in 1947 to promote the development of international manufacturing, trade and communication standards. The organization is now represented in 118 countries, with the American National Standards Institute (ANSI) representing the United States. The principal goals of the ISO is "to promote the development of standardization and related ac¬tivities in the world with a view toward facilitating the international exchange of goods and services and to develop cooperation in the sphere of intellectual, scientific, technological and economic activity." ISO develops standards with input from government and industry. Because the standards are voluntary, there are no legal requirements to pressure countries to adopt them. However, many governments, industries and US agencies are adopting the ISO standards as a requirement for business trans¬actions, thereby, compelling suppliers to adopt ISO standards. These business and market forces, which are likely to be strategic business issues in the 21st century global marketplace, are imposing the need to develop a systematic approach to environmental management. The ISO 14000 series evolved from a United Nations Conference on the Human Environment in 1972. It includes a broad range of elements: the basic environmental management system, environmental auditing criteria for internal and external auditors, criteria for environmental performance evaluation (EPE), environmental labeling criteria and life-cycle assessment methodologies. The standards comprise two categories: organization evaluation standards and product oriented standards (Table 1). The ISO 14001 specifications contain the requirements for developing an environmental-management system that may be objectively audited for certification. The ISO 14004 standard provides guidance on interpreting the ISO 14000 specifications for the development and implementation of the EMS and for coordination with the management system of the company. On Sept. 1, 1996, the American National Standards Institute (ANSI) and the Registrar Accreditation Board (RAB) signed a formal agreement to create a new entity called the National Accreditation Program (NAP). To obtain certification, a company must fulfill the requirements outlined in ISO 14001. It is required that "a third party give written assurance that a company's EMS meets all the requirements of ISO 14001." Preparing for ISO 14000 can include subscribing to voluntary environmental initiatives; learning from ISO 9000 quality-management experiences; and utilizing information from recognized training courses, publications and numerous Internet resources. Once committed to an EMS, the management should provide sufficient resources to achieve continuous environmental-performance improvement, as outlined in an environmental policy. A thorny issue now being debated concerns the potential liabilities of documenting the environmental performance of a company. General impact of the ISO 14000 EMS standards. With increasing stakeholder awareness, costly end-of-pipe pollution-control approaches and the success of ISO 9000 quality-management standards, the ISO 14000 EMS standards are being adopted by companies and governments worldwide. The United States and Canada have well-established programs. In Europe, countries differ but are firmly committed toward environmental-management standards (BS 7750, EMAS and ISO 14000). The Department of Environmental Protec¬tion of the State of Pennsylvania is using ISO 14000 as a vehicle to develop a closer working relationship with industry, and it is anticipated that this policy will eventually lead to fewer environmental site inspections for those companies with ISO 14001 certification. The Depart-

Jan 1, 1999

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997